* G28 - X0 Y0 Z0 Home all Axis. G28 M for bed manual setting with LCD.
* G28 - X0 Y0 Z0 Home all Axis. G28 M for bed manual setting with LCD.
* G29 - Detailed Z-Probe, probes the bed at 3 points or grid. You must be at the home position for this to work correctly.
* G29 - Detailed Z-Probe, probes the bed at 3 points or grid. You must be at the home position for this to work correctly.
G29 Fyyy Lxxx Rxxx Byyy for customer grid.
G29 Fyyy Lxxx Rxxx Byyy for customer grid.
* G30 - Single Z Probe, probes bed at current XY location.
* G30 - Single Z Probe, probes bed at current XY location. Bed Probe and Delta geometry Autocalibration G30 A
Bed Probe and Delta geometry Autocalibration G30 A
* G31 - Dock Z Probe sled (if enabled)
* G31 - Dock Z Probe sled (if enabled)
* G32 - Undock Z Probe sled (if enabled)
* G32 - Undock Z Probe sled (if enabled)
* G60 - Save current position coordinates (all axes, for active extruder). S<SLOT> - specifies memory slot # (0-based) to save into (default 0).
* G60 - Save current position coordinates (all axes, for active extruder). S<SLOT> - specifies memory slot # (0-based) to save into (default 0).
...
@@ -60,7 +59,7 @@
...
@@ -60,7 +59,7 @@
* M109 - S[xxx] Wait for extruder current temp to reach target temp. Waits only when heating - R[xxx] Wait for extruder current temp to reach target temp. Waits when heating and cooling
* M109 - S[xxx] Wait for extruder current temp to reach target temp. Waits only when heating - R[xxx] Wait for extruder current temp to reach target temp. Waits when heating and cooling
* M111 - Debug Dryrun Repetier
* M111 - Debug Dryrun Repetier
* M112 - Emergency stop
* M112 - Emergency stop
* M114 - Output current position to serial port, (V)erbose for user
*M114 - Output current position to serial port, (V)erbose for user
* M115 - Capabilities string
* M115 - Capabilities string
* M117 - display message
* M117 - display message
* M119 - Output Endstop status to serial port
* M119 - Output Endstop status to serial port
...
@@ -100,8 +99,8 @@
...
@@ -100,8 +99,8 @@
* M405 - Turn on Filament Sensor extrusion control. Optional D[delay in cm] to set delay in centimeters between sensor and extruder
* M405 - Turn on Filament Sensor extrusion control. Optional D[delay in cm] to set delay in centimeters between sensor and extruder
* M406 - Turn off Filament Sensor extrusion control
* M406 - Turn off Filament Sensor extrusion control
* M407 - Displays measured filament diameter
* M407 - Displays measured filament diameter
* M410 - Quickstop. Abort all the planned moves
*M410 - Quickstop. Abort all the planned moves
* M428 - Set the home_offset logically based on the current_position
*M428 - Set the home_offset logically based on the current_position
* M500 - stores paramters in EEPROM
* M500 - stores paramters in EEPROM
* M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
* M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
* M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
* M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
