Fix

MarlinKimbra/Configuration.h

@@ -528,6 +528,15 @@
 //=============================Additional Features===========================
 //===========================================================================
 
+// Custom M code points
+#define CUSTOM_M_CODES
+#ifdef CUSTOM_M_CODES
+#define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
+#define Z_PROBE_OFFSET_RANGE_MIN -15
+#define Z_PROBE_OFFSET_RANGE_MAX -5
+#endif
+
+
 // EEPROM
 // The microcontroller can store settings in the EEPROM, e.g. max velocity...
 // M500 - stores parameters in EEPROM
@@ -594,6 +603,28 @@
 // define laser beam support
 //#define LASERBEAM
 
+
+/*********************************************************************\
+ * R/C SERVO support
+ * Sponsored by TrinityLabs, Reworked by codexmas
+ **********************************************************************/
+
+// Number of servos
+//
+// If you select a configuration below, this will receive a default value and does not need to be set manually
+// set it manually if you have more servos than extruders and wish to manually control some
+// leaving it defining as 0 will disable the servo subsystem
+#define NUM_SERVOS 0     // Servo index starts with 0 for M280 command
+
+// Servo Endstops
+//
+// This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes.
+// Use M206 command to correct for switch height offset to actual nozzle height. Store that setting with M500.
+//
+#define SERVO_ENDSTOPS {-1,-1,0}     // Servo index for X, Y, Z. Disable with -1
+#define SERVO_ENDSTOP_ANGLES {0,0,0,0,90,0}     // X,Y,Z Axis Extend and Retract angles
+
+
 /**********************************************************************\
  * Support for a filament diameter sensor
  * Also allows adjustment of diameter at print time (vs  at slicing)

MarlinKimbra/Configuration_Cartesian.h

@@ -214,36 +214,4 @@ const bool Z_MAX_ENDSTOP_INVERTING = false;      // set to true to invert the lo
 // The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously)
 #define DEFAULT_XYJERK 10.0    // (mm/sec)
 #define DEFAULT_ZJERK 0.4      // (mm/sec)
-#define DEFAULT_EJERK 5.0      // (mm/sec)
-
-//===========================================================================
-//=============================Additional Features===========================
-//===========================================================================
-
-// Custom M code points
-#define CUSTOM_M_CODES
-#ifdef CUSTOM_M_CODES
-#define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
-#define Z_PROBE_OFFSET_RANGE_MIN -15
-#define Z_PROBE_OFFSET_RANGE_MAX -5
-#endif
-
-/*********************************************************************\
- * R/C SERVO support
- * Sponsored by TrinityLabs, Reworked by codexmas
- **********************************************************************/
-
-// Number of servos
-//
-// If you select a configuration below, this will receive a default value and does not need to be set manually
-// set it manually if you have more servos than extruders and wish to manually control some
-// leaving it defining as 0 will disable the servo subsystem
-#define NUM_SERVOS 0     // Servo index starts with 0 for M280 command
-
-// Servo Endstops
-//
-// This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes.
-// Use M206 command to correct for switch height offset to actual nozzle height. Store that setting with M500.
-//
-#define SERVO_ENDSTOPS {-1, -1, 0}     // Servo index for X, Y, Z. Disable with -1
-#define SERVO_ENDSTOP_ANGLES {0,0, 0,0, 90,0}     // X,Y,Z Axis Extend and Retract angles
\ No newline at end of file
+#define DEFAULT_EJERK 5.0      // (mm/sec)
\ No newline at end of file

MarlinKimbra/Configuration_Corexy.h

@@ -214,39 +214,4 @@ const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 // The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously)
 #define DEFAULT_XYJERK                10.0    // (mm/sec)
 #define DEFAULT_ZJERK                 0.4     // (mm/sec)
-#define DEFAULT_EJERK                 5.0    // (mm/sec)
-
-//===========================================================================
-//=============================Additional Features===========================
-//===========================================================================
-
-// Custom M code points
-#define CUSTOM_M_CODES
-#ifdef CUSTOM_M_CODES
-#define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
-#define Z_PROBE_OFFSET_RANGE_MIN -15
-#define Z_PROBE_OFFSET_RANGE_MAX -5
-#endif
-
-/*********************************************************************\
- * R/C SERVO support
- * Sponsored by TrinityLabs, Reworked by codexmas
- **********************************************************************/
-
-// Number of servos
-//
-// If you select a configuration below, this will receive a default value and does not need to be set manually
-// set it manually if you have more servos than extruders and wish to manually control some
-// leaving it undefined or defining as 0 will disable the servo subsystem
-// If unsure, leave commented / disabled
-//
-//#define NUM_SERVOS 1 // Servo index starts with 0 for M280 command
-
-// Servo Endstops
-//
-// This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes.
-// Use M206 command to correct for switch height offset to actual nozzle height. Store that setting with M500.
-//
-//#define SERVO_ENDSTOPS {-1, -1, 0} // Servo index for X, Y, Z. Disable with -1
-//#define SERVO_ENDSTOP_ANGLES {0,0, 0,0, 70,0} // X,Y,Z Axis Extend and Retract angles
-
+#define DEFAULT_EJERK                 5.0    // (mm/sec)
\ No newline at end of file

MarlinKimbra/Configuration_Scara.h

@@ -237,38 +237,4 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 // The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously)
 #define DEFAULT_XYJERK                5    // (mm/sec)
 #define DEFAULT_ZJERK                 0.4    // (mm/sec)
-#define DEFAULT_EJERK                 3    // (mm/sec)
-
-//===========================================================================
-//=============================Additional Features===========================
-//===========================================================================
-
-// Custom M code points
-//#define CUSTOM_M_CODES
-#ifdef CUSTOM_M_CODES
-#define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
-#define Z_PROBE_OFFSET_RANGE_MIN -15
-#define Z_PROBE_OFFSET_RANGE_MAX -5
-#endif
-
-/*********************************************************************\
- * R/C SERVO support
- * Sponsored by TrinityLabs, Reworked by codexmas
- **********************************************************************/
-
-// Number of servos
-//
-// If you select a configuration below, this will receive a default value and does not need to be set manually
-// set it manually if you have more servos than extruders and wish to manually control some
-// leaving it undefined or defining as 0 will disable the servo subsystem
-// If unsure, leave commented / disabled
-//
-//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
-
-// Servo Endstops
-//
-// This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes.
-// Use M206 command to correct for switch height offset to actual nozzle height. Store that setting with M500.
-//
-//#define SERVO_ENDSTOPS {-1, -1, 0} // Servo index for X, Y, Z. Disable with -1
-//#define SERVO_ENDSTOP_ANGLES {0,0, 0,0, 70,0} // X,Y,Z Axis Extend and Retract angles
+#define DEFAULT_EJERK                 3    // (mm/sec)
\ No newline at end of file