Clear text in temperature.cpp

MarlinKimbra/language.h

@@ -149,6 +149,42 @@
 
 #define MSG_ERR_EEPROM_WRITE                "Error writing to EEPROM!"
 
+#define MSG_PID_AUTOTUNE                    "PID Autotune"
+#define MSG_PID_AUTOTUNE_START              MSG_PID_AUTOTUNE " start"
+#define MSG_PID_AUTOTUNE_FAILED             MSG_PID_AUTOTUNE " failed!"
+#define MSG_PID_BAD_EXTRUDER_NUM            MSG_PID_AUTOTUNE_FAILED " Bad extruder number"
+#define MSG_PID_TEMP_TOO_HIGH               MSG_PID_AUTOTUNE_FAILED " Temperature too high"
+#define MSG_PID_TIMEOUT                     MSG_PID_AUTOTUNE_FAILED " timeout"
+#define MSG_BIAS                            " bias: "
+#define MSG_D                               " d: "
+#define MSG_MIN                             " min: "
+#define MSG_MAX                             " max: "
+#define MSG_KU                              " Ku: "
+#define MSG_TU                              " Tu: "
+#define MSG_CLASSIC_PID                     " Classic PID "
+#define MSG_KP                              " Kp: "
+#define MSG_KI                              " Ki: "
+#define MSG_KD                              " Kd: "
+#define MSG_OK_B                            "ok B:"
+#define MSG_OK_T                            "ok T:"
+#define MSG_AT                              " @:"
+#define MSG_PID_AUTOTUNE_FINISHED           MSG_PID_AUTOTUNE " finished! Put the last Kp, Ki and Kd constants from above into Configuration.h"
+#define MSG_PID_DEBUG                       " PID_DEBUG "
+#define MSG_PID_DEBUG_INPUT                 ": Input "
+#define MSG_PID_DEBUG_OUTPUT                " Output "
+#define MSG_PID_DEBUG_PTERM                 " pTerm "
+#define MSG_PID_DEBUG_ITERM                 " iTerm "
+#define MSG_PID_DEBUG_DTERM                 " dTerm "
+#define MSG_HEATING_FAILED                  "Heating failed"
+#define MSG_EXTRUDER_SWITCHED_OFF           "Extruder switched off. Temperature difference between temp sensors is too high !"
+
+#define MSG_INVALID_EXTRUDER_NUM            " - Invalid extruder number !"
+#define MSG_THERMAL_RUNAWAY_STOP            "Thermal Runaway, system stopped! Heater_ID: "
+#define MSG_SWITCHED_OFF_MAX                " switched off. MAXTEMP triggered !!"
+#define MSG_MINTEMP_EXTRUDER_OFF            ": Extruder switched off. MINTEMP triggered !"
+#define MSG_MAXTEMP_EXTRUDER_OFF            ": Extruder" MSG_SWITCHED_OFF_MAX
+#define MSG_MAXTEMP_BED_OFF                 "Heated bed" MSG_SWITCHED_OFF_MAX
+
 // Add your own character. Reference: https://www.sparkfun.com/datasheets/LCD/HD44780.pdf page 17-18
 #ifdef DOGLCD
   #define STR_Ae "\304"               // 'Ä' U8glib

MarlinKimbra/language_an.h

@@ -122,6 +122,13 @@
 #define MSG_BABYSTEP_Z                      "Babystep Z"
 #define MSG_ENDSTOP_ABORT                   "Endstop abort"
 
+#define MSG_HEATING_FAILED_LCD              "Heating failed"
+#define MSG_ERR_REDUNDANT_TEMP              "Err: REDUNDANT TEMP ERROR"
+#define MSG_THERMAL_RUNAWAY                 "THERMAL RUNAWAY"
+#define MSG_ERR_MAXTEMP                     "Err: MAXTEMP"
+#define MSG_ERR_MINTEMP                     "Err: MINTEMP"
+#define MSG_ERR_MAXTEMP_BED                 "Err: MAXTEMP BED"
+
 #ifdef DELTA
   #define MSG_DELTA_CALIBRATE               "Delta Calibration"
   #define MSG_DELTA_CALIBRATE_X             "Calibrate X"
@@ -139,20 +146,20 @@
 #define MSG_RETRACT_XMM                     "Retract " STRINGIFY(LCD_RETRACT_LENGTH) "mm"
 
 #ifdef FIRMWARE_TEST
-  #define MSG_FWTEST_YES                      "Put the Y command to go next"
-  #define MSG_FWTEST_NO                       "Put the N command to go next"
-  #define MSG_FWTEST_YES_NO                   "Put the Y or N command to go next"
-  #define MSG_FWTEST_ENDSTOP_ERR              "ENDSTOP ERROR! Check wire and connection"
-  #define MSG_FWTEST_PRESS                    "Press and hold the endstop "
-  #define MSG_FWTEST_INVERT                   "Reverse value in "
-  #define MSG_FWTEST_XAXIS                    "Has the nozzle moved to the right?"
-  #define MSG_FWTEST_YAXIS                    "Has the nozzle moved forward?"
-  #define MSG_FWTEST_ZAXIS                    "Has the nozzle moved up?"
-  #define MSG_FWTEST_01                       "Manually move the axes X, Y and Z away from the endstop"
-  #define MSG_FWTEST_02                       "Do you want check ENDSTOP?"
-  #define MSG_FWTEST_03                       "Start check ENDSTOP"
-  #define MSG_FWTEST_04                       "Start check MOTOR"
-  #define MSG_FWTEST_ATTENTION                "ATTENTION! Check that the three axes are more than 5 mm from the endstop!"
+  #define MSG_FWTEST_YES                    "Put the Y command to go next"
+  #define MSG_FWTEST_NO                     "Put the N command to go next"
+  #define MSG_FWTEST_YES_NO                 "Put the Y or N command to go next"
+  #define MSG_FWTEST_ENDSTOP_ERR            "ENDSTOP ERROR! Check wire and connection"
+  #define MSG_FWTEST_PRESS                  "Press and hold the endstop "
+  #define MSG_FWTEST_INVERT                 "Reverse value in "
+  #define MSG_FWTEST_XAXIS                  "Has the nozzle moved to the right?"
+  #define MSG_FWTEST_YAXIS                  "Has the nozzle moved forward?"
+  #define MSG_FWTEST_ZAXIS                  "Has the nozzle moved up?"
+  #define MSG_FWTEST_01                     "Manually move the axes X, Y and Z away from the endstop"
+  #define MSG_FWTEST_02                     "Do you want check ENDSTOP?"
+  #define MSG_FWTEST_03                     "Start check ENDSTOP"
+  #define MSG_FWTEST_04                     "Start check MOTOR"
+  #define MSG_FWTEST_ATTENTION              "ATTENTION! Check that the three axes are more than 5 mm from the endstop!"
 #endif // FIRMWARE_TEST
 
 #endif // LANGUAGE_AN_H

MarlinKimbra/language_ca.h

@@ -122,6 +122,13 @@
 #define MSG_BABYSTEP_Z                      "Babystep Z"
 #define MSG_ENDSTOP_ABORT                   "Endstop abort"
 
+#define MSG_HEATING_FAILED_LCD              "Heating failed"
+#define MSG_ERR_REDUNDANT_TEMP              "Err: REDUNDANT TEMP ERROR"
+#define MSG_THERMAL_RUNAWAY                 "THERMAL RUNAWAY"
+#define MSG_ERR_MAXTEMP                     "Err: MAXTEMP"
+#define MSG_ERR_MINTEMP                     "Err: MINTEMP"
+#define MSG_ERR_MAXTEMP_BED                 "Err: MAXTEMP BED"
+
 #ifdef DELTA
   #define MSG_DELTA_CALIBRATE               "Delta Calibration"
   #define MSG_DELTA_CALIBRATE_X             "Calibrate X"
@@ -139,20 +146,20 @@
 #define MSG_RETRACT_XMM                     "Retract " STRINGIFY(LCD_RETRACT_LENGTH) "mm"
 
 #ifdef FIRMWARE_TEST
-  #define MSG_FWTEST_YES                      "Put the Y command to go next"
-  #define MSG_FWTEST_NO                       "Put the N command to go next"
-  #define MSG_FWTEST_YES_NO                   "Put the Y or N command to go next"
-  #define MSG_FWTEST_ENDSTOP_ERR              "ENDSTOP ERROR! Check wire and connection"
-  #define MSG_FWTEST_PRESS                    "Press and hold the endstop "
-  #define MSG_FWTEST_INVERT                   "Reverse value in "
-  #define MSG_FWTEST_XAXIS                    "Has the nozzle moved to the right?"
-  #define MSG_FWTEST_YAXIS                    "Has the nozzle moved forward?"
-  #define MSG_FWTEST_ZAXIS                    "Has the nozzle moved up?"
-  #define MSG_FWTEST_01                       "Manually move the axes X, Y and Z away from the endstop"
-  #define MSG_FWTEST_02                       "Do you want check ENDSTOP?"
-  #define MSG_FWTEST_03                       "Start check ENDSTOP"
-  #define MSG_FWTEST_04                       "Start check MOTOR"
-  #define MSG_FWTEST_ATTENTION                "ATTENTION! Check that the three axes are more than 5 mm from the endstop!"
+  #define MSG_FWTEST_YES                    "Put the Y command to go next"
+  #define MSG_FWTEST_NO                     "Put the N command to go next"
+  #define MSG_FWTEST_YES_NO                 "Put the Y or N command to go next"
+  #define MSG_FWTEST_ENDSTOP_ERR            "ENDSTOP ERROR! Check wire and connection"
+  #define MSG_FWTEST_PRESS                  "Press and hold the endstop "
+  #define MSG_FWTEST_INVERT                 "Reverse value in "
+  #define MSG_FWTEST_XAXIS                  "Has the nozzle moved to the right?"
+  #define MSG_FWTEST_YAXIS                  "Has the nozzle moved forward?"
+  #define MSG_FWTEST_ZAXIS                  "Has the nozzle moved up?"
+  #define MSG_FWTEST_01                     "Manually move the axes X, Y and Z away from the endstop"
+  #define MSG_FWTEST_02                     "Do you want check ENDSTOP?"
+  #define MSG_FWTEST_03                     "Start check ENDSTOP"
+  #define MSG_FWTEST_04                     "Start check MOTOR"
+  #define MSG_FWTEST_ATTENTION              "ATTENTION! Check that the three axes are more than 5 mm from the endstop!"
 #endif // FIRMWARE_TEST
 
 #endif // LANGUAGE_EN_H

MarlinKimbra/language_de.h

@@ -122,6 +122,13 @@
 #define MSG_BABYSTEP_Z                      "Babystep Z"
 #define MSG_ENDSTOP_ABORT                   "Endstop abort"
 
+#define MSG_HEATING_FAILED_LCD              "Heating failed"
+#define MSG_ERR_REDUNDANT_TEMP              "Err: REDUNDANT TEMP ERROR"
+#define MSG_THERMAL_RUNAWAY                 "THERMAL RUNAWAY"
+#define MSG_ERR_MAXTEMP                     "Err: MAXTEMP"
+#define MSG_ERR_MINTEMP                     "Err: MINTEMP"
+#define MSG_ERR_MAXTEMP_BED                 "Err: MAXTEMP BED"
+
 #ifdef DELTA
   #define MSG_DELTA_CALIBRATE               "Delta Calibration"
   #define MSG_DELTA_CALIBRATE_X             "Calibrate X"

MarlinKimbra/language_en.h

@@ -122,6 +122,13 @@
 #define MSG_BABYSTEP_Z                      "Babystep Z"
 #define MSG_ENDSTOP_ABORT                   "Endstop abort"
 
+#define MSG_HEATING_FAILED_LCD              "Heating failed"
+#define MSG_ERR_REDUNDANT_TEMP              "Err: REDUNDANT TEMP ERROR"
+#define MSG_THERMAL_RUNAWAY                 "THERMAL RUNAWAY"
+#define MSG_ERR_MAXTEMP                     "Err: MAXTEMP"
+#define MSG_ERR_MINTEMP                     "Err: MINTEMP"
+#define MSG_ERR_MAXTEMP_BED                 "Err: MAXTEMP BED"
+
 #ifdef DELTA
   #define MSG_DELTA_CALIBRATE               "Delta Calibration"
   #define MSG_DELTA_CALIBRATE_X             "Calibrate X"

MarlinKimbra/language_es.h

@@ -122,6 +122,13 @@
 #define MSG_BABYSTEP_Z                      "Babystep Z"
 #define MSG_ENDSTOP_ABORT                   "Endstop abort"
 
+#define MSG_HEATING_FAILED_LCD              "Heating failed"
+#define MSG_ERR_REDUNDANT_TEMP              "Err: REDUNDANT TEMP ERROR"
+#define MSG_THERMAL_RUNAWAY                 "THERMAL RUNAWAY"
+#define MSG_ERR_MAXTEMP                     "Err: MAXTEMP"
+#define MSG_ERR_MINTEMP                     "Err: MINTEMP"
+#define MSG_ERR_MAXTEMP_BED                 "Err: MAXTEMP BED"
+
 #ifdef DELTA
   #define MSG_DELTA_CALIBRATE               "Delta Calibration"
   #define MSG_DELTA_CALIBRATE_X             "Calibrate X"

MarlinKimbra/language_eu.h

@@ -122,6 +122,13 @@
 #define MSG_BABYSTEP_Z                      "Babystep Z"
 #define MSG_ENDSTOP_ABORT                   "Endstop deuseztat"
 
+#define MSG_HEATING_FAILED_LCD              "Heating failed"
+#define MSG_ERR_REDUNDANT_TEMP              "Err: REDUNDANT TEMP ERROR"
+#define MSG_THERMAL_RUNAWAY                 "THERMAL RUNAWAY"
+#define MSG_ERR_MAXTEMP                     "Err: MAXTEMP"
+#define MSG_ERR_MINTEMP                     "Err: MINTEMP"
+#define MSG_ERR_MAXTEMP_BED                 "Err: MAXTEMP BED"
+
 #ifdef DELTA
   #define MSG_DELTA_CALIBRATE               "Delta Calibration"
   #define MSG_DELTA_CALIBRATE_X             "Calibrate X"

MarlinKimbra/language_fi.h

@@ -122,6 +122,13 @@
 #define MSG_BABYSTEP_Z                      "Babystep Z"
 #define MSG_ENDSTOP_ABORT                   "Endstop abort"
 
+#define MSG_HEATING_FAILED_LCD              "Heating failed"
+#define MSG_ERR_REDUNDANT_TEMP              "Err: REDUNDANT TEMP ERROR"
+#define MSG_THERMAL_RUNAWAY                 "THERMAL RUNAWAY"
+#define MSG_ERR_MAXTEMP                     "Err: MAXTEMP"
+#define MSG_ERR_MINTEMP                     "Err: MINTEMP"
+#define MSG_ERR_MAXTEMP_BED                 "Err: MAXTEMP BED"
+
 #ifdef DELTA
   #define MSG_DELTA_CALIBRATE               "Delta Kalibrointi"
   #define MSG_DELTA_CALIBRATE_X             "Kalibroi X"

MarlinKimbra/language_fr.h

@@ -122,6 +122,13 @@
 #define MSG_BABYSTEP_Z                      "Babystep Z"
 #define MSG_ENDSTOP_ABORT                   "Butee abandon"
 
+#define MSG_HEATING_FAILED_LCD              "Heating failed"
+#define MSG_ERR_REDUNDANT_TEMP              "Err: REDUNDANT TEMP ERROR"
+#define MSG_THERMAL_RUNAWAY                 "THERMAL RUNAWAY"
+#define MSG_ERR_MAXTEMP                     "Err: MAXTEMP"
+#define MSG_ERR_MINTEMP                     "Err: MINTEMP"
+#define MSG_ERR_MAXTEMP_BED                 "Err: MAXTEMP BED"
+
 #ifdef DELTA
   #define MSG_DELTA_CALIBRATE               "Delta Calibration"
   #define MSG_DELTA_CALIBRATE_X             "Calibrate X"

MarlinKimbra/language_it.h

@@ -122,6 +122,13 @@
 #define MSG_BABYSTEP_Z                      "Babystep Z"
 #define MSG_ENDSTOP_ABORT                   "Finecorsa abort"
 
+#define MSG_HEATING_FAILED_LCD              "Heating failed"
+#define MSG_ERR_REDUNDANT_TEMP              "Err: REDUNDANT TEMP ERROR"
+#define MSG_THERMAL_RUNAWAY                 "THERMAL RUNAWAY"
+#define MSG_ERR_MAXTEMP                     "Err: MAXTEMP"
+#define MSG_ERR_MINTEMP                     "Err: MINTEMP"
+#define MSG_ERR_MAXTEMP_BED                 "Err: MAXTEMP BED"
+
 #ifdef DELTA
   #define MSG_DELTA_CALIBRATE               "Calibraz. Delta"
   #define MSG_DELTA_CALIBRATE_X             "Calibra X"

MarlinKimbra/language_nl.h

@@ -122,6 +122,13 @@
 #define MSG_BABYSTEP_Z                      "Babystap Z"
 #define MSG_ENDSTOP_ABORT                   "Endstop afbr."
 
+#define MSG_HEATING_FAILED_LCD              "Heating failed"
+#define MSG_ERR_REDUNDANT_TEMP              "Err: REDUNDANT TEMP ERROR"
+#define MSG_THERMAL_RUNAWAY                 "THERMAL RUNAWAY"
+#define MSG_ERR_MAXTEMP                     "Err: MAXTEMP"
+#define MSG_ERR_MINTEMP                     "Err: MINTEMP"
+#define MSG_ERR_MAXTEMP_BED                 "Err: MAXTEMP BED"
+
 #ifdef DELTA
   #define MSG_DELTA_CALIBRATE               "Delta Calibration"
   #define MSG_DELTA_CALIBRATE_X             "Calibrate X"

MarlinKimbra/language_pl.h

@@ -122,6 +122,13 @@
 #define MSG_BABYSTEP_Z                      "Babystep Z"
 #define MSG_ENDSTOP_ABORT                   "Blad wyl. kranc."
 
+#define MSG_HEATING_FAILED_LCD              "Heating failed"
+#define MSG_ERR_REDUNDANT_TEMP              "Err: REDUNDANT TEMP ERROR"
+#define MSG_THERMAL_RUNAWAY                 "THERMAL RUNAWAY"
+#define MSG_ERR_MAXTEMP                     "Err: MAXTEMP"
+#define MSG_ERR_MINTEMP                     "Err: MINTEMP"
+#define MSG_ERR_MAXTEMP_BED                 "Err: MAXTEMP BED"
+
 #ifdef DELTA
   #define MSG_DELTA_CALIBRATE               "Delta Calibration"
   #define MSG_DELTA_CALIBRATE_X             "Calibrate X"

MarlinKimbra/language_pt-br.h

@@ -122,6 +122,13 @@
 #define MSG_BABYSTEP_Z                      "Babystep Z"
 #define MSG_ENDSTOP_ABORT                   "Endstop abort"
 
+#define MSG_HEATING_FAILED_LCD              "Heating failed"
+#define MSG_ERR_REDUNDANT_TEMP              "Err: REDUNDANT TEMP ERROR"
+#define MSG_THERMAL_RUNAWAY                 "THERMAL RUNAWAY"
+#define MSG_ERR_MAXTEMP                     "Err: MAXTEMP"
+#define MSG_ERR_MINTEMP                     "Err: MINTEMP"
+#define MSG_ERR_MAXTEMP_BED                 "Err: MAXTEMP BED"
+
 #ifdef DELTA
   #define MSG_DELTA_CALIBRATE               "Delta Calibration"
   #define MSG_DELTA_CALIBRATE_X             "Calibrate X"

MarlinKimbra/language_pt.h

@@ -122,6 +122,13 @@
 #define MSG_BABYSTEP_Z                      "Babystep Z"
 #define MSG_ENDSTOP_ABORT                   "Endstop abort"
 
+#define MSG_HEATING_FAILED_LCD              "Heating failed"
+#define MSG_ERR_REDUNDANT_TEMP              "Err: REDUNDANT TEMP ERROR"
+#define MSG_THERMAL_RUNAWAY                 "THERMAL RUNAWAY"
+#define MSG_ERR_MAXTEMP                     "Err: MAXTEMP"
+#define MSG_ERR_MINTEMP                     "Err: MINTEMP"
+#define MSG_ERR_MAXTEMP_BED                 "Err: MAXTEMP BED"
+
 #ifdef DELTA
   #define MSG_DELTA_CALIBRATE               "Delta Calibration"
   #define MSG_DELTA_CALIBRATE_X             "Calibrate X"

MarlinKimbra/language_ru.h

@@ -122,6 +122,13 @@
 #define MSG_BABYSTEP_Z                      "Babystep Z"
 #define MSG_ENDSTOP_ABORT                   "Endstop abort"
 
+#define MSG_HEATING_FAILED_LCD              "Heating failed"
+#define MSG_ERR_REDUNDANT_TEMP              "Err: REDUNDANT TEMP ERROR"
+#define MSG_THERMAL_RUNAWAY                 "THERMAL RUNAWAY"
+#define MSG_ERR_MAXTEMP                     "Err: MAXTEMP"
+#define MSG_ERR_MINTEMP                     "Err: MINTEMP"
+#define MSG_ERR_MAXTEMP_BED                 "Err: MAXTEMP BED"
+
 #ifdef DELTA
   #define MSG_DELTA_CALIBRATE               "Delta Calibration"
   #define MSG_DELTA_CALIBRATE_X             "Calibrate X"