Skip to content

M
MarlinKimbra
Commit e5722514 authored by MagoKimbra's avatar MagoKimbra
Browse files
Options

Merge remote-tracking branch 'refs/remotes/origin/dev'

parents 01e3b720 2797e1bc
Expand all Hide whitespace changes
Inline Side-by-side
Showing with 1662 additions and 218 deletions
MK/Configuration_Feature.h
View file @ e5722514
...@@ -284,7 +284,7 @@ ...@@ -284,7 +284,7 @@
/** /**
* Thermal Protection parameters for the bed are just as above for hotends. * Thermal Protection parameters for the bed are just as above for hotends.
*/ */
//#define THERMAL_PROTECTION_BED //#define THERMAL_PROTECTION_BED
#define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
...@@ -608,18 +608,35 @@ ...@@ -608,18 +608,35 @@
* * * *
* Add support for filament exchange support M600 * * Add support for filament exchange support M600 *
* * * *
* Uncomment FILAMENTCHANGEENABLE to enable this feature * * Uncomment FILAMENT CHANGE FEATURE to enable this feature *
* Requires display * * Requires display *
* * * *
**************************************************************************/ **************************************************************************/
//#define FILAMENTCHANGEENABLE //#define FILAMENT_CHANGE_FEATURE
#define FILAMENTCHANGE_XPOS 3 #define FILAMENT_CHANGE_X_POS 3 // X position of hotend
#define FILAMENTCHANGE_YPOS 3 #define FILAMENT_CHANGE_Y_POS 3 // Y position of hotend
#define FILAMENTCHANGE_ZADD 10 #define FILAMENT_CHANGE_Z_ADD 10 // Z addition of hotend (lift)
#define FILAMENTCHANGE_FIRSTRETRACT -2 #define FILAMENT_CHANGE_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
#define FILAMENTCHANGE_FINALRETRACT -100 #define FILAMENT_CHANGE_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers)
#define FILAMENTCHANGE_PRINTEROFF 5 // Minutes #define FILAMENT_CHANGE_RETRACT_LENGTH 2 // Initial retract in mm
// It is a short retract used immediately after print interrupt before move to filament exchange position
#define FILAMENT_CHANGE_RETRACT_FEEDRATE 50 // Initial retract feedrate in mm/s
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
// Longer length for bowden printers to unload filament from whole bowden tube,
// shorter lenght for printers without bowden to unload filament from extruder only,
// 0 to disable unloading for manual unloading
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 100 // Unload filament feedrate in mm/s - filament unloading can be fast
#define FILAMENT_CHANGE_LOAD_LENGTH 100 // Load filament length over hotend in mm
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
// Short or zero length for printers without bowden where loading is not used
#define FILAMENT_CHANGE_LOAD_FEEDRATE 100 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
#define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend,
// 0 to disable for manual extrusion
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
// or until outcoming filament color is not clear for filament color change
#define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 5 // Extrude filament feedrate in mm/s - must be slower than load feedrate
#define FILAMENT_CHANGE_PRINTER_OFF 5 // Minutes
/**************************************************************************/ /**************************************************************************/
......
MK/module/MK_Main.cpp
View file @ e5722514
This diff is collapsed.
MK/module/MK_Main.h
View file @ e5722514
...@@ -29,7 +29,7 @@ ...@@ -29,7 +29,7 @@
void get_command(); void get_command();
void idle( void idle(
#if ENABLED(FILAMENTCHANGEENABLE) #if ENABLED(FILAMENT_CHANGE_FEATURE)
bool no_stepper_sleep=false // pass true to keep steppers from disabling on timeout bool no_stepper_sleep=false // pass true to keep steppers from disabling on timeout
#endif #endif
); );
...@@ -196,6 +196,15 @@ extern int fanSpeed; ...@@ -196,6 +196,15 @@ extern int fanSpeed;
extern int meas_delay_cm; //delay distance extern int meas_delay_cm; //delay distance
#endif #endif
#if ENABLED(FILAMENT_CHANGE_FEATURE)
enum FilamentChangeMenuResponse {
FILAMENT_CHANGE_RESPONSE_WAIT_FOR,
FILAMENT_CHANGE_RESPONSE_EXTRUDE_MORE,
FILAMENT_CHANGE_RESPONSE_RESUME_PRINT
};
extern FilamentChangeMenuResponse filament_change_menu_response;
#endif
#if HAS(POWER_CONSUMPTION_SENSOR) #if HAS(POWER_CONSUMPTION_SENSOR)
extern float power_consumption_meas; //holds the power consumption as accurately measured extern float power_consumption_meas; //holds the power consumption as accurately measured
extern unsigned long power_consumption_hour; //holds the power consumption per hour as accurately measured extern unsigned long power_consumption_hour; //holds the power consumption per hour as accurately measured
......
MK/module/language/language.h
View file @ e5722514
...@@ -12,11 +12,11 @@ ...@@ -12,11 +12,11 @@
* *
* This program is distributed in the hope that it will be useful, * This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of * but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details. * GNU General Public License for more details.
* *
* You should have received a copy of the GNU General Public License * You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>. * along with this program. If not, see <http://www.gnu.org/licenses/>.
* *
*/ */
......
MK/module/language/language_an.h
View file @ e5722514
/**
* MK & MK4due 3D Printer Firmware
*
* Based on Marlin, Sprinter and grbl
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
* Copyright (C) 2013 - 2016 Alberto Cotronei @MagoKimbra
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/** /**
* Aragonese * Aragonese
* *
...@@ -13,7 +35,7 @@ ...@@ -13,7 +35,7 @@
#define WELCOME_MSG MACHINE_NAME " parada." #define WELCOME_MSG MACHINE_NAME " parada."
#define MSG_SD "SD" #define MSG_SD "Tarcheta"
#define MSG_SD_INSERTED MSG_SD " colocada" #define MSG_SD_INSERTED MSG_SD " colocada"
#define MSG_SD_REMOVED MSG_SD " retirada" #define MSG_SD_REMOVED MSG_SD " retirada"
#define MSG_MAIN "Menu prencipal" #define MSG_MAIN "Menu prencipal"
...@@ -34,20 +56,19 @@ ...@@ -34,20 +56,19 @@
#define MSG_ONFOR "On x:" #define MSG_ONFOR "On x:"
#define MSG_PWRCONSUMED "P.er:" #define MSG_PWRCONSUMED "P.er:"
#define MSG_FILCONSUMED "F:" #define MSG_FILCONSUMED "F:"
#define MSG_PREHEAT "Prec." #define MSG_PREHEAT "Precalentar"
#define MSG_CONGIG "conf." #define MSG_PREHEAT_PLA "Precalentar PLA"
#define MSG_PREHEAT_PLA MSG_PREHEAT " PLA" #define MSG_PREHEAT_PLA_ALL "Precalentar PLA a"
#define MSG_PREHEAT_PLA_ALL MSG_PREHEAT_PLA " All" #define MSG_PREHEAT_PLA_BEDONLY "Prec. PLA Base"
#define MSG_PREHEAT_PLA_BEDONLY MSG_PREHEAT_PLA " Bed" #define MSG_PREHEAT_PLA_SETTINGS "Achustar tem. PLA"
#define MSG_PREHEAT_PLA_SETTINGS MSG_CONGIG " PLA" #define MSG_PREHEAT_ABS "Precalentar ABS"
#define MSG_PREHEAT_ABS MSG_PREHEAT " ABS" #define MSG_PREHEAT_ABS_ALL "Precalentar ABS a"
#define MSG_PREHEAT_ABS_ALL MSG_PREHEAT_ABS " All" #define MSG_PREHEAT_ABS_BEDONLY "Prec. ABS Base"
#define MSG_PREHEAT_ABS_BEDONLY MSG_PREHEAT_ABS " Bed" #define MSG_PREHEAT_ABS_SETTINGS "Achustar tem. ABS"
#define MSG_PREHEAT_ABS_SETTINGS MSG_CONGIG " ABS" #define MSG_PREHEAT_GUM "Precalentar GUM"
#define MSG_PREHEAT_GUM MSG_PREHEAT " GUM" #define MSG_PREHEAT_GUM_ALL "Precalentar GUM a"
#define MSG_PREHEAT_GUM_ALL MSG_PREHEAT_GUM " All" #define MSG_PREHEAT_GUM_BEDONLY "Achustar tem. "
#define MSG_PREHEAT_GUM_BEDONLY MSG_PREHEAT_GUM " Bed" #define MSG_PREHEAT_GUM_SETTINGS "Achustar tem. GUM"
#define MSG_PREHEAT_GUM_SETTINGS MSG_CONGIG " GUM"
#define MSG_TOO_COLD_FOR_FILAMENTCHANGE "Hotend too cold to change filament" #define MSG_TOO_COLD_FOR_FILAMENTCHANGE "Hotend too cold to change filament"
#define MSG_COOLDOWN "Enfriar" #define MSG_COOLDOWN "Enfriar"
#define MSG_SWITCH_PS_ON "Enchegar Fuent" #define MSG_SWITCH_PS_ON "Enchegar Fuent"
...@@ -69,8 +90,8 @@ ...@@ -69,8 +90,8 @@
#define MSG_FACTOR LCD_STR_THERMOMETER " Fact" #define MSG_FACTOR LCD_STR_THERMOMETER " Fact"
#define MSG_IDLEOOZING "Anti oozing" #define MSG_IDLEOOZING "Anti oozing"
#define MSG_AUTOTEMP "Autotemp" #define MSG_AUTOTEMP "Autotemp"
#define MSG_ON "ON " #define MSG_ON "On"
#define MSG_OFF "OFF" #define MSG_OFF "Off"
#define MSG_PID_P "PID-P" #define MSG_PID_P "PID-P"
#define MSG_PID_I "PID-I" #define MSG_PID_I "PID-I"
#define MSG_PID_D "PID-D" #define MSG_PID_D "PID-D"
...@@ -82,13 +103,13 @@ ...@@ -82,13 +103,13 @@
#define MSG_VXY_JERK "Vxy-jerk" #define MSG_VXY_JERK "Vxy-jerk"
#define MSG_VZ_JERK "Vz-jerk" #define MSG_VZ_JERK "Vz-jerk"
#define MSG_VE_JERK "Ves-jerk" #define MSG_VE_JERK "Ves-jerk"
#define MSG_VMAX "Vmax " #define MSG_VMAX "Vmax"
#define MSG_X "X" #define MSG_X "X"
#define MSG_Y "Y" #define MSG_Y "Y"
#define MSG_Z "Z" #define MSG_Z "Z"
#define MSG_E "E" #define MSG_E "E"
#define MSG_MOVE "Move" #define MSG_MOVE "Mover"
#define MSG_MOVE_AXIS MSG_MOVE " axis" #define MSG_MOVE_AXIS MSG_MOVE " Eixes"
#define MSG_MOVE_X MSG_MOVE " " MSG_X #define MSG_MOVE_X MSG_MOVE " " MSG_X
#define MSG_MOVE_Y MSG_MOVE " " MSG_Y #define MSG_MOVE_Y MSG_MOVE " " MSG_Y
#define MSG_MOVE_Z MSG_MOVE " " MSG_Z #define MSG_MOVE_Z MSG_MOVE " " MSG_Z
...@@ -98,7 +119,7 @@ ...@@ -98,7 +119,7 @@
#define MSG_MOVE_E "Extruder" #define MSG_MOVE_E "Extruder"
#define MSG_VMIN "Vmin" #define MSG_VMIN "Vmin"
#define MSG_VTRAV_MIN "VTrav min" #define MSG_VTRAV_MIN "VTrav min"
#define MSG_AMAX "Amax " #define MSG_AMAX "Amax"
#define MSG_A_RETRACT "A-retrac." #define MSG_A_RETRACT "A-retrac."
#define MSG_A_TRAVEL "A-travel" #define MSG_A_TRAVEL "A-travel"
#define MSG_XSTEPS MSG_X " trangos/mm" #define MSG_XSTEPS MSG_X " trangos/mm"
...@@ -124,8 +145,8 @@ ...@@ -124,8 +145,8 @@
#define MSG_PAUSE_PRINT "Pausar impresion" #define MSG_PAUSE_PRINT "Pausar impresion"
#define MSG_RESUME_PRINT "Contin. impresion" #define MSG_RESUME_PRINT "Contin. impresion"
#define MSG_STOP_PRINT "Detener Impresion" #define MSG_STOP_PRINT "Detener Impresion"
#define MSG_CARD_MENU "Menu de " MSG_SD #define MSG_CARD_MENU "Menu de SD"
#define MSG_NO_CARD "No i hai " MSG_SD #define MSG_NO_CARD "No i hai tarcheta"
#define MSG_DWELL "Reposo..." #define MSG_DWELL "Reposo..."
#define MSG_USERWAIT "Asperan. ordines" #define MSG_USERWAIT "Asperan. ordines"
#define MSG_RESUMING "Contin. impresion" #define MSG_RESUMING "Contin. impresion"
...@@ -134,7 +155,7 @@ ...@@ -134,7 +155,7 @@
#define MSG_KILLED "ATURADA D'EMERCH." #define MSG_KILLED "ATURADA D'EMERCH."
#define MSG_STOPPED "ATURADA." #define MSG_STOPPED "ATURADA."
#define MSG_CONTROL_RETRACT "Retraer mm" #define MSG_CONTROL_RETRACT "Retraer mm"
#define MSG_CONTROL_RETRACT_SWAP "Swap Re. mm" #define MSG_CONTROL_RETRACT_SWAP "Swap Retraer mm"
#define MSG_CONTROL_RETRACTF "Retraer F" #define MSG_CONTROL_RETRACTF "Retraer F"
#define MSG_CONTROL_RETRACT_ZLIFT "Devantar mm" #define MSG_CONTROL_RETRACT_ZLIFT "Devantar mm"
#define MSG_CONTROL_RETRACT_RECOVER "DesRet +mm" #define MSG_CONTROL_RETRACT_RECOVER "DesRet +mm"
...@@ -142,8 +163,8 @@ ...@@ -142,8 +163,8 @@
#define MSG_CONTROL_RETRACT_RECOVERF "DesRet F" #define MSG_CONTROL_RETRACT_RECOVERF "DesRet F"
#define MSG_AUTORETRACT "AutoRetr." #define MSG_AUTORETRACT "AutoRetr."
#define MSG_FILAMENTCHANGE "Cambear" #define MSG_FILAMENTCHANGE "Cambear"
#define MSG_INIT_SDCARD "Encetan. " MSG_SD #define MSG_INIT_SDCARD "Encetan. tarcheta"
#define MSG_CNG_SDCARD "Cambiar " MSG_SD #define MSG_CNG_SDCARD "Cambiar tarcheta"
#define MSG_ZPROBE_OUT "Z probe out. bed" #define MSG_ZPROBE_OUT "Z probe out. bed"
#define MSG_POSITION_UNKNOWN "Home X/Y before Z" #define MSG_POSITION_UNKNOWN "Home X/Y before Z"
#define MSG_ZPROBE_ZOFFSET "Z Offset" #define MSG_ZPROBE_ZOFFSET "Z Offset"
...@@ -155,7 +176,7 @@ ...@@ -155,7 +176,7 @@
#define MSG_HEATING_FAILED_LCD "Heating failed" #define MSG_HEATING_FAILED_LCD "Heating failed"
#define MSG_ERR_REDUNDANT_TEMP "REDUNDANT TEMP ERROR" #define MSG_ERR_REDUNDANT_TEMP "REDUNDANT TEMP ERROR"
#define MSG_THERMAL_RUNAWAY "THERMAL RUNAWAY" #define MSG_THERMAL_RUNAWAY "THERMAL RUNAWAY"
#define MSG_HOTEND_AD595 "HOTEND AD595 Offset & Gain" #define MSG_AD595 "AD595 Offset & Gain"
#define MSG_ERR_MAXTEMP "MAXTEMP ERROR" #define MSG_ERR_MAXTEMP "MAXTEMP ERROR"
#define MSG_ERR_MINTEMP "MINTEMP ERROR" #define MSG_ERR_MINTEMP "MINTEMP ERROR"
#define MSG_ERR_MAXTEMP_BED "MAXTEMP BED ERROR" #define MSG_ERR_MAXTEMP_BED "MAXTEMP BED ERROR"
...@@ -212,9 +233,13 @@ ...@@ -212,9 +233,13 @@
#if ENABLED(RFID_MODULE) #if ENABLED(RFID_MODULE)
#define MSG_RFID_SPOOL "Spool on E" #define MSG_RFID_SPOOL "Spool on E"
#define MSG_RFID_BRAND "Brand: " #define MSG_RFID_BRAND "Brand: "
#define MSG_RFID_TYPE "Type: "
#define MSG_RFID_COLOR "Color: " #define MSG_RFID_COLOR "Color: "
#define MSG_RFID_SIZE "Size: " #define MSG_RFID_SIZE "Size: "
#define MSG_RFID_TEMPERATURE "Temperature: " #define MSG_RFID_TEMP_HOTEND "Temperature Hotend: "
#define MSG_RFID_TEMP_BED "Temperature Bed: "
#define MSG_RFID_TEMP_USER_HOTEND "User temperature Hotend: "
#define MSG_RFID_TEMP_USER_BED "User temperatura Bed: "
#define MSG_RFID_DENSITY "Density: " #define MSG_RFID_DENSITY "Density: "
#define MSG_RFID_SPOOL_LENGHT "Spool Lenght: " #define MSG_RFID_SPOOL_LENGHT "Spool Lenght: "
#endif #endif
......
MK/module/language/language_bg.h
View file @ e5722514
/** /**
* MK & MK4due 3D Printer Firmware
*
* Based on Marlin, Sprinter and grbl
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
* Copyright (C) 2013 - 2016 Alberto Cotronei @MagoKimbra
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* Bulgarian * Bulgarian
* *
* LCD Menu Messages * LCD Menu Messages
...@@ -13,9 +35,8 @@ ...@@ -13,9 +35,8 @@
#define WELCOME_MSG MACHINE_NAME " Готов." #define WELCOME_MSG MACHINE_NAME " Готов."
#define MSG_SD "SD" #define MSG_SD_INSERTED "Картата е поставена"
#define MSG_SD_INSERTED MSG_SD " поставена" #define MSG_SD_REMOVED "Картата е извадена"
#define MSG_SD_REMOVED MSG_SD " извадена"
#define MSG_MAIN "Меню" #define MSG_MAIN "Меню"
#define MSG_AUTOSTART "Автостарт" #define MSG_AUTOSTART "Автостарт"
#define MSG_DISABLE_STEPPERS "Изкл. двигатели" #define MSG_DISABLE_STEPPERS "Изкл. двигатели"
...@@ -155,7 +176,7 @@ ...@@ -155,7 +176,7 @@
#define MSG_HEATING_FAILED_LCD "Heating failed" #define MSG_HEATING_FAILED_LCD "Heating failed"
#define MSG_ERR_REDUNDANT_TEMP "REDUNDANT TEMP ERROR" #define MSG_ERR_REDUNDANT_TEMP "REDUNDANT TEMP ERROR"
#define MSG_THERMAL_RUNAWAY "THERMAL RUNAWAY" #define MSG_THERMAL_RUNAWAY "THERMAL RUNAWAY"
#define MSG_HOTEND_AD595 "HOTEND AD595 Offset & Gain" #define MSG_AD595 "AD595 Offset & Gain"
#define MSG_ERR_MAXTEMP "MAXTEMP ERROR" #define MSG_ERR_MAXTEMP "MAXTEMP ERROR"
#define MSG_ERR_MINTEMP "MINTEMP ERROR" #define MSG_ERR_MINTEMP "MINTEMP ERROR"
#define MSG_ERR_MAXTEMP_BED "MAXTEMP BED ERROR" #define MSG_ERR_MAXTEMP_BED "MAXTEMP BED ERROR"
...@@ -212,9 +233,13 @@ ...@@ -212,9 +233,13 @@
#if ENABLED(RFID_MODULE) #if ENABLED(RFID_MODULE)
#define MSG_RFID_SPOOL "Spool on E" #define MSG_RFID_SPOOL "Spool on E"
#define MSG_RFID_BRAND "Brand: " #define MSG_RFID_BRAND "Brand: "
#define MSG_RFID_TYPE "Type: "
#define MSG_RFID_COLOR "Color: " #define MSG_RFID_COLOR "Color: "
#define MSG_RFID_SIZE "Size: " #define MSG_RFID_SIZE "Size: "
#define MSG_RFID_TEMPERATURE "Temperature: " #define MSG_RFID_TEMP_HOTEND "Temperature Hotend: "
#define MSG_RFID_TEMP_BED "Temperature Bed: "
#define MSG_RFID_TEMP_USER_HOTEND "User temperature Hotend: "
#define MSG_RFID_TEMP_USER_BED "User temperatura Bed: "
#define MSG_RFID_DENSITY "Density: " #define MSG_RFID_DENSITY "Density: "
#define MSG_RFID_SPOOL_LENGHT "Spool Lenght: " #define MSG_RFID_SPOOL_LENGHT "Spool Lenght: "
#endif #endif
......
MK/module/language/language_ca.h
View file @ e5722514
/**
* MK & MK4due 3D Printer Firmware
*
* Based on Marlin, Sprinter and grbl
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
* Copyright (C) 2013 - 2016 Alberto Cotronei @MagoKimbra
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/** /**
* Catalan * Catalan
* *
...@@ -154,7 +176,7 @@ ...@@ -154,7 +176,7 @@
#define MSG_HEATING_FAILED_LCD "Heating failed" #define MSG_HEATING_FAILED_LCD "Heating failed"
#define MSG_ERR_REDUNDANT_TEMP "REDUNDANT TEMP ERROR" #define MSG_ERR_REDUNDANT_TEMP "REDUNDANT TEMP ERROR"
#define MSG_THERMAL_RUNAWAY "THERMAL RUNAWAY" #define MSG_THERMAL_RUNAWAY "THERMAL RUNAWAY"
#define MSG_HOTEND_AD595 "HOTEND AD595 Offset & Gain" #define MSG_AD595 "AD595 Offset & Gain"
#define MSG_ERR_MAXTEMP "MAXTEMP ERROR" #define MSG_ERR_MAXTEMP "MAXTEMP ERROR"
#define MSG_ERR_MINTEMP "MINTEMP ERROR" #define MSG_ERR_MINTEMP "MINTEMP ERROR"
#define MSG_ERR_MAXTEMP_BED "MAXTEMP BED ERROR" #define MSG_ERR_MAXTEMP_BED "MAXTEMP BED ERROR"
...@@ -211,9 +233,13 @@ ...@@ -211,9 +233,13 @@
#if ENABLED(RFID_MODULE) #if ENABLED(RFID_MODULE)
#define MSG_RFID_SPOOL "Spool on E" #define MSG_RFID_SPOOL "Spool on E"
#define MSG_RFID_BRAND "Brand: " #define MSG_RFID_BRAND "Brand: "
#define MSG_RFID_TYPE "Type: "
#define MSG_RFID_COLOR "Color: " #define MSG_RFID_COLOR "Color: "
#define MSG_RFID_SIZE "Size: " #define MSG_RFID_SIZE "Size: "
#define MSG_RFID_TEMPERATURE "Temperature: " #define MSG_RFID_TEMP_HOTEND "Temperature Hotend: "
#define MSG_RFID_TEMP_BED "Temperature Bed: "
#define MSG_RFID_TEMP_USER_HOTEND "User temperature Hotend: "
#define MSG_RFID_TEMP_USER_BED "User temperatura Bed: "
#define MSG_RFID_DENSITY "Density: " #define MSG_RFID_DENSITY "Density: "
#define MSG_RFID_SPOOL_LENGHT "Spool Lenght: " #define MSG_RFID_SPOOL_LENGHT "Spool Lenght: "
#endif #endif
......
MK/module/language/language_cn.h
View file @ e5722514
/**
* MK & MK4due 3D Printer Firmware
*
* Based on Marlin, Sprinter and grbl
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
* Copyright (C) 2013 - 2016 Alberto Cotronei @MagoKimbra
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/** /**
* Chinese * Chinese
* *
...@@ -154,7 +176,7 @@ ...@@ -154,7 +176,7 @@
#define MSG_HEATING_FAILED_LCD "Heating failed" #define MSG_HEATING_FAILED_LCD "Heating failed"
#define MSG_ERR_REDUNDANT_TEMP "REDUNDANT TEMP ERROR" #define MSG_ERR_REDUNDANT_TEMP "REDUNDANT TEMP ERROR"
#define MSG_THERMAL_RUNAWAY "THERMAL RUNAWAY" #define MSG_THERMAL_RUNAWAY "THERMAL RUNAWAY"
#define MSG_HOTEND_AD595 "HOTEND AD595 Offset & Gain" #define MSG_AD595 "AD595 Offset & Gain"
#define MSG_ERR_MAXTEMP "MAXTEMP ERROR" #define MSG_ERR_MAXTEMP "MAXTEMP ERROR"
#define MSG_ERR_MINTEMP "MINTEMP ERROR" #define MSG_ERR_MINTEMP "MINTEMP ERROR"
#define MSG_ERR_MAXTEMP_BED "MAXTEMP BED ERROR" #define MSG_ERR_MAXTEMP_BED "MAXTEMP BED ERROR"
...@@ -211,9 +233,13 @@ ...@@ -211,9 +233,13 @@
#if ENABLED(RFID_MODULE) #if ENABLED(RFID_MODULE)
#define MSG_RFID_SPOOL "Spool on E" #define MSG_RFID_SPOOL "Spool on E"
#define MSG_RFID_BRAND "Brand: " #define MSG_RFID_BRAND "Brand: "
#define MSG_RFID_TYPE "Type: "
#define MSG_RFID_COLOR "Color: " #define MSG_RFID_COLOR "Color: "
#define MSG_RFID_SIZE "Size: " #define MSG_RFID_SIZE "Size: "
#define MSG_RFID_TEMPERATURE "Temperature: " #define MSG_RFID_TEMP_HOTEND "Temperature Hotend: "
#define MSG_RFID_TEMP_BED "Temperature Bed: "
#define MSG_RFID_TEMP_USER_HOTEND "User temperature Hotend: "
#define MSG_RFID_TEMP_USER_BED "User temperatura Bed: "
#define MSG_RFID_DENSITY "Density: " #define MSG_RFID_DENSITY "Density: "
#define MSG_RFID_SPOOL_LENGHT "Spool Lenght: " #define MSG_RFID_SPOOL_LENGHT "Spool Lenght: "
#endif #endif
......
MK/module/language/language_cz.h 0 → 100644
View file @ e5722514
This diff is collapsed.
MK/module/language/language_da.h
View file @ e5722514
/**
* MK & MK4due 3D Printer Firmware
*
* Based on Marlin, Sprinter and grbl
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
* Copyright (C) 2013 - 2016 Alberto Cotronei @MagoKimbra
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/** /**
* Danish * Danish
* *
...@@ -154,7 +176,7 @@ ...@@ -154,7 +176,7 @@
#define MSG_HEATING_FAILED_LCD "Heating failed" #define MSG_HEATING_FAILED_LCD "Heating failed"
#define MSG_ERR_REDUNDANT_TEMP "REDUNDANT TEMP ERROR" #define MSG_ERR_REDUNDANT_TEMP "REDUNDANT TEMP ERROR"
#define MSG_THERMAL_RUNAWAY "THERMAL RUNAWAY" #define MSG_THERMAL_RUNAWAY "THERMAL RUNAWAY"
#define MSG_HOTEND_AD595 "HOTEND AD595 Offset & Gain" #define MSG_AD595 "AD595 Offset & Gain"
#define MSG_ERR_MAXTEMP "MAXTEMP ERROR" #define MSG_ERR_MAXTEMP "MAXTEMP ERROR"
#define MSG_ERR_MINTEMP "MINTEMP ERROR" #define MSG_ERR_MINTEMP "MINTEMP ERROR"
#define MSG_ERR_MAXTEMP_BED "MAXTEMP BED ERROR" #define MSG_ERR_MAXTEMP_BED "MAXTEMP BED ERROR"
...@@ -211,9 +233,13 @@ ...@@ -211,9 +233,13 @@
#if ENABLED(RFID_MODULE) #if ENABLED(RFID_MODULE)
#define MSG_RFID_SPOOL "Spool on E" #define MSG_RFID_SPOOL "Spool on E"
#define MSG_RFID_BRAND "Brand: " #define MSG_RFID_BRAND "Brand: "
#define MSG_RFID_TYPE "Type: "
#define MSG_RFID_COLOR "Color: " #define MSG_RFID_COLOR "Color: "
#define MSG_RFID_SIZE "Size: " #define MSG_RFID_SIZE "Size: "
#define MSG_RFID_TEMPERATURE "Temperature: " #define MSG_RFID_TEMP_HOTEND "Temperature Hotend: "
#define MSG_RFID_TEMP_BED "Temperature Bed: "
#define MSG_RFID_TEMP_USER_HOTEND "User temperature Hotend: "
#define MSG_RFID_TEMP_USER_BED "User temperatura Bed: "
#define MSG_RFID_DENSITY "Density: " #define MSG_RFID_DENSITY "Density: "
#define MSG_RFID_SPOOL_LENGHT "Spool Lenght: " #define MSG_RFID_SPOOL_LENGHT "Spool Lenght: "
#endif #endif
......
MK/module/language/language_de.h
View file @ e5722514
/**
* MK & MK4due 3D Printer Firmware
*
* Based on Marlin, Sprinter and grbl
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
* Copyright (C) 2013 - 2016 Alberto Cotronei @MagoKimbra
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/** /**
* German * German
* *
...@@ -154,7 +176,7 @@ ...@@ -154,7 +176,7 @@
#define MSG_HEATING_FAILED_LCD "Heating failed" #define MSG_HEATING_FAILED_LCD "Heating failed"
#define MSG_ERR_REDUNDANT_TEMP "Err: REDUNDANT TEMP ERROR" #define MSG_ERR_REDUNDANT_TEMP "Err: REDUNDANT TEMP ERROR"
#define MSG_THERMAL_RUNAWAY "THERMAL RUNAWAY" #define MSG_THERMAL_RUNAWAY "THERMAL RUNAWAY"
#define MSG_HOTEND_AD595 "HOTEND AD595 Offset & Gain" #define MSG_AD595 "AD595 Offset & Gain"
#define MSG_ERR_MAXTEMP "MAXTEMP ERROR" #define MSG_ERR_MAXTEMP "MAXTEMP ERROR"
#define MSG_ERR_MINTEMP "MINTEMP ERROR" #define MSG_ERR_MINTEMP "MINTEMP ERROR"
#define MSG_ERR_MAXTEMP_BED "MAXTEMP BED ERROR" #define MSG_ERR_MAXTEMP_BED "MAXTEMP BED ERROR"
...@@ -211,9 +233,13 @@ ...@@ -211,9 +233,13 @@
#if ENABLED(RFID_MODULE) #if ENABLED(RFID_MODULE)
#define MSG_RFID_SPOOL "Spool on E" #define MSG_RFID_SPOOL "Spool on E"
#define MSG_RFID_BRAND "Brand: " #define MSG_RFID_BRAND "Brand: "
#define MSG_RFID_TYPE "Type: "
#define MSG_RFID_COLOR "Color: " #define MSG_RFID_COLOR "Color: "
#define MSG_RFID_SIZE "Size: " #define MSG_RFID_SIZE "Size: "
#define MSG_RFID_TEMPERATURE "Temperature: " #define MSG_RFID_TEMP_HOTEND "Temperature Hotend: "
#define MSG_RFID_TEMP_BED "Temperature Bed: "
#define MSG_RFID_TEMP_USER_HOTEND "User temperature Hotend: "
#define MSG_RFID_TEMP_USER_BED "User temperatura Bed: "
#define MSG_RFID_DENSITY "Density: " #define MSG_RFID_DENSITY "Density: "
#define MSG_RFID_SPOOL_LENGHT "Spool Lenght: " #define MSG_RFID_SPOOL_LENGHT "Spool Lenght: "
#endif #endif
......
MK/module/language/language_en.h
View file @ e5722514
/**
* MK & MK4due 3D Printer Firmware
*
* Based on Marlin, Sprinter and grbl
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
* Copyright (C) 2013 - 2016 Alberto Cotronei @MagoKimbra
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/** /**
* English * English
* *
...@@ -140,7 +162,7 @@ ...@@ -140,7 +162,7 @@
#define MSG_CONTROL_RETRACT_RECOVER_SWAP "Swap UnRet +mm" #define MSG_CONTROL_RETRACT_RECOVER_SWAP "Swap UnRet +mm"
#define MSG_CONTROL_RETRACT_RECOVERF "UnRet F" #define MSG_CONTROL_RETRACT_RECOVERF "UnRet F"
#define MSG_AUTORETRACT "AutoRetr." #define MSG_AUTORETRACT "AutoRetr."
#define MSG_FILAMENTCHANGE "Change filament" #define MSG_FILAMENT_CHANGE "Change filament"
#define MSG_INIT_SDCARD "Init. " MSG_SD #define MSG_INIT_SDCARD "Init. " MSG_SD
#define MSG_CNG_SDCARD "Change " MSG_SD #define MSG_CNG_SDCARD "Change " MSG_SD
#define MSG_ZPROBE_OUT "Z probe out. bed" #define MSG_ZPROBE_OUT "Z probe out. bed"
...@@ -184,6 +206,30 @@ ...@@ -184,6 +206,30 @@
#define MSG_DELTA_CALIBRATE_CENTER "Calibrate Center" #define MSG_DELTA_CALIBRATE_CENTER "Calibrate Center"
#endif // DELTA #endif // DELTA
// FILAMENT_CHANGE_FEATURE
#define MSG_FILAMENT_CHANGE_HEADER "CHANGE FILAMENT"
#define MSG_FILAMENT_CHANGE_INIT_1 "Wait for start"
#define MSG_FILAMENT_CHANGE_INIT_2 "of the filament"
#define MSG_FILAMENT_CHANGE_INIT_3 "change"
#define MSG_FILAMENT_CHANGE_UNLOAD_1 "Wait for"
#define MSG_FILAMENT_CHANGE_UNLOAD_2 "filament unload"
#define MSG_FILAMENT_CHANGE_UNLOAD_3 ""
#define MSG_FILAMENT_CHANGE_INSERT_1 "Insert filament"
#define MSG_FILAMENT_CHANGE_INSERT_2 "and press button"
#define MSG_FILAMENT_CHANGE_INSERT_3 "to continue..."
#define MSG_FILAMENT_CHANGE_LOAD_1 "Wait for"
#define MSG_FILAMENT_CHANGE_LOAD_2 "filament load"
#define MSG_FILAMENT_CHANGE_LOAD_3 ""
#define MSG_FILAMENT_CHANGE_EXTRUDE_1 "Wait for"
#define MSG_FILAMENT_CHANGE_EXTRUDE_2 "filament extrude"
#define MSG_FILAMENT_CHANGE_EXTRUDE_3 ""
#define MSG_FILAMENT_CHANGE_OPTION_HEADER "WHAT NEXT?"
#define MSG_FILAMENT_CHANGE_OPTION_EXTRUDE "Extrude more"
#define MSG_FILAMENT_CHANGE_OPTION_RESUME "Resume print"
#define MSG_FILAMENT_CHANGE_RESUME_1 "Wait for print"
#define MSG_FILAMENT_CHANGE_RESUME_2 "resume"
#define MSG_FILAMENT_CHANGE_RESUME_3 ""
// Scara // Scara
#if MECH(SCARA) #if MECH(SCARA)
#define MSG_SCALE "Scale" #define MSG_SCALE "Scale"
......
MK/module/language/language_es.h
View file @ e5722514
/**
* MK & MK4due 3D Printer Firmware
*
* Based on Marlin, Sprinter and grbl
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
* Copyright (C) 2013 - 2016 Alberto Cotronei @MagoKimbra
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/** /**
* Spanish * Spanish
* *
......
MK/module/language/language_eu.h
View file @ e5722514
/**
* MK & MK4due 3D Printer Firmware
*
* Based on Marlin, Sprinter and grbl
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
* Copyright (C) 2013 - 2016 Alberto Cotronei @MagoKimbra
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/** /**
* Basque-Euskera * Basque-Euskera
* *
......
MK/module/language/language_fi.h
View file @ e5722514
/**
* MK & MK4due 3D Printer Firmware
*
* Based on Marlin, Sprinter and grbl
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
* Copyright (C) 2013 - 2016 Alberto Cotronei @MagoKimbra
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/** /**
* Finnish * Finnish
* *
......
MK/module/language/language_fr.h
View file @ e5722514
/**
* MK & MK4due 3D Printer Firmware
*
* Based on Marlin, Sprinter and grbl
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
* Copyright (C) 2013 - 2016 Alberto Cotronei @MagoKimbra
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/** /**
* French * French
* *
......
MK/module/language/language_gl.h 0 → 100644
View file @ e5722514
/**
* MK & MK4due 3D Printer Firmware
*
* Based on Marlin, Sprinter and grbl
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
* Copyright (C) 2013 - 2016 Alberto Cotronei @MagoKimbra
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* Galician language (ISO "gl")
*
* LCD Menu Messages
* See also documentation/LCDLanguageFont.md
*
*/
#ifndef LANGUAGE_GL_H
#define LANGUAGE_GL_H
#define MAPPER_C2C3
// Define SIMULATE_ROMFONT to see what is seen on the character based display defined in Configuration.h
//#define SIMULATE_ROMFONT
#define DISPLAY_CHARSET_ISO10646_1
#define WELCOME_MSG MACHINE_NAME " lista."
#define MSG_SD_INSERTED "Tarxeta inserida"
#define MSG_SD_REMOVED "Tarxeta retirada"
#define MSG_MAIN "Menu principal"
#define MSG_AUTOSTART "Autoarranque"
#define MSG_DISABLE_STEPPERS "Apagar motores"
#define MSG_AUTO_HOME "Ir a orixe"
#define MSG_SET_ORIGIN "Fixar orixe"
#define MSG_PREHEAT_PLA "Prequentar PLA"
#define MSG_PREHEAT_PLA_N "Prequentar PLA "
#define MSG_PREHEAT_PLA_ALL "Preque. PLA Todo"
#define MSG_PREHEAT_PLA_BEDONLY "Preque. PLA Cama"
#define MSG_PREHEAT_PLA_SETTINGS "Preque. PLA conf"
#define MSG_PREHEAT_ABS "Prequentar ABS"
#define MSG_PREHEAT_ABS_N "Prequentar ABS "
#define MSG_PREHEAT_ABS_ALL "Preque. ABS Todo"
#define MSG_PREHEAT_ABS_BEDONLY "Preque. ABS Cama"
#define MSG_PREHEAT_ABS_SETTINGS "Preque. ABS conf"
#define MSG_COOLDOWN "Arrefriar"
#define MSG_SWITCH_PS_ON "Acender"
#define MSG_SWITCH_PS_OFF "Apagar"
#define MSG_EXTRUDE "Extrudir"
#define MSG_RETRACT "Retraer"
#define MSG_MOVE_AXIS "Mover eixe"
#define MSG_LEVEL_BED "Nivelar cama"
#define MSG_MOVE_X "Mover X"
#define MSG_MOVE_Y "Mover Y"
#define MSG_MOVE_Z "Mover Z"
#define MSG_MOVE_E "Extruir"
#define MSG_MOVE_01MM "Mover 0.1mm"
#define MSG_MOVE_1MM "Mover 1mm"
#define MSG_MOVE_10MM "Mover 10mm"
#define MSG_SPEED "Velocidade"
#define MSG_NOZZLE "Bico"
#define MSG_BED "Cama"
#define MSG_FAN_SPEED "Velocidade vent."
#define MSG_FLOW "Fluxo"
#define MSG_CONTROL "Control"
#define MSG_MIN " " LCD_STR_THERMOMETER " Min"
#define MSG_MAX " " LCD_STR_THERMOMETER " Max"
#define MSG_FACTOR " " LCD_STR_THERMOMETER " Fact"
#define MSG_AUTOTEMP "Autotemp"
#define MSG_ON "On "
#define MSG_OFF "Off"
#define MSG_PID_P "PID-P"
#define MSG_PID_I "PID-I"
#define MSG_PID_D "PID-D"
#define MSG_PID_C "PID-C"
#define MSG_E1 " E1"
#define MSG_E2 " E2"
#define MSG_E3 " E3"
#define MSG_E4 " E4"
#define MSG_ACC "Acel"
#define MSG_VXY_JERK "Vxy-jerk"
#define MSG_VZ_JERK "Vz-jerk"
#define MSG_VE_JERK "Ve-jerk"
#define MSG_VMAX "Vmax "
#define MSG_X "X"
#define MSG_Y "Y"
#define MSG_Z "Z"
#define MSG_E "E"
#define MSG_VMIN "Vmin"
#define MSG_VTRAV_MIN "VTrav min"
#define MSG_AMAX "Amax "
#define MSG_A_RETRACT "A-retract"
#define MSG_A_TRAVEL "A-travel"
#define MSG_XSTEPS "Xpasos/mm"
#define MSG_YSTEPS "Ypasos/mm"
#define MSG_ZSTEPS "Zpasos/mm"
#define MSG_ESTEPS "Epasos/mm"
#define MSG_TEMPERATURE "Temperatura"
#define MSG_MOTION "Movemento"
#define MSG_VOLUMETRIC "Filamento"
#define MSG_VOLUMETRIC_ENABLED "E en mm3"
#define MSG_FILAMENT_DIAM "Diametro filam."
#define MSG_CONTRAST "Constraste LCD"
#define MSG_STORE_EPROM "Gardar en memo."
#define MSG_LOAD_EPROM "Cargar de memo."
#define MSG_RESTORE_FAILSAFE "Cargar de firm."
#define MSG_REFRESH "Volver a cargar"
#define MSG_WATCH "Monitorizacion"
#define MSG_PREPARE "Preparar"
#define MSG_TUNE "Axustar"
#define MSG_PAUSE_PRINT "Pausar impres."
#define MSG_RESUME_PRINT "Seguir impres."
#define MSG_STOP_PRINT "Deter impres."
#define MSG_CARD_MENU "Tarxeta SD"
#define MSG_NO_CARD "Sen tarxeta SD"
#define MSG_DWELL "En repouso..."
#define MSG_USERWAIT "A espera..."
#define MSG_RESUMING "Imprimindo..."
#define MSG_PRINT_ABORTED "Impre. cancelada"
#define MSG_NO_MOVE "Sen movemento."
#define MSG_KILLED "PROGRAMA MORTO"
#define MSG_STOPPED "PROGRAMA PARADO"
#define MSG_CONTROL_RETRACT "Retraccion mm"
#define MSG_CONTROL_RETRACT_SWAP "Cambio retra. mm"
#define MSG_CONTROL_RETRACTF "Retraccion V"
#define MSG_CONTROL_RETRACT_ZLIFT "Alzar Z mm"
#define MSG_CONTROL_RETRACT_RECOVER "Recup. retra. mm"
#define MSG_CONTROL_RETRACT_RECOVER_SWAP "Cambio recup. mm"
#define MSG_CONTROL_RETRACT_RECOVERF "Recuperacion V"
#define MSG_AUTORETRACT "Retraccion auto."
#define MSG_FILAMENTCHANGE "Cambiar filamen."
#define MSG_INIT_SDCARD "Iniciando SD"
#define MSG_CNG_SDCARD "Cambiar SD"
#define MSG_ZPROBE_OUT "Sonda-Z sen cama"
#define MSG_YX_UNHOMED "X/Y antes que Z"
#define MSG_ZPROBE_ZOFFSET "Offset Z"
#define MSG_BABYSTEP_X "Micropaso X"
#define MSG_BABYSTEP_Y "Micropaso Y"
#define MSG_BABYSTEP_Z "Micropaso Z"
#define MSG_ENDSTOP_ABORT "Erro fin carro"
#define MSG_HEATING_FAILED_LCD "Fallo quentando"
#define MSG_ERR_REDUNDANT_TEMP "Erro temperatura"
#define MSG_THERMAL_RUNAWAY "Temp. excesiva"
#define MSG_ERR_MAXTEMP "Err: temp. max."
#define MSG_ERR_MINTEMP "Err: temp. min."
#define MSG_ERR_MAXTEMP_BED "Err: MAXTEMP BED"
#define MSG_ERR_MINTEMP_BED "Err: MINTEMP BED"
#define MSG_END_HOUR "horas"
#define MSG_END_MINUTE "minutos"
#define MSG_HEATING "Quentando..."
#define MSG_HEATING_COMPLETE "Xa esta quente"
#define MSG_BED_HEATING "Quentando cama"
#define MSG_BED_DONE "Cama esta quente"
#define MSG_DELTA_CALIBRATE "Calibracion Delta"
#define MSG_DELTA_CALIBRATE_X "Calibrar X"
#define MSG_DELTA_CALIBRATE_Y "Calibrar Y"
#define MSG_DELTA_CALIBRATE_Z "Calibrar Z"
#define MSG_DELTA_CALIBRATE_CENTER "Calibrar Centro"
#endif // LANGUAGE_GL_H
MK/module/language/language_it.h
View file @ e5722514
/**
* MK & MK4due 3D Printer Firmware
*
* Based on Marlin, Sprinter and grbl
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
* Copyright (C) 2013 - 2016 Alberto Cotronei @MagoKimbra
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/** /**
* Italian * Italian
* *
...@@ -140,7 +162,7 @@ ...@@ -140,7 +162,7 @@
#define MSG_CONTROL_RETRACT_RECOVER_SWAP "Scamb. UnRet +mm" #define MSG_CONTROL_RETRACT_RECOVER_SWAP "Scamb. UnRet +mm"
#define MSG_CONTROL_RETRACT_RECOVERF "UnRet V" #define MSG_CONTROL_RETRACT_RECOVERF "UnRet V"
#define MSG_AUTORETRACT "AutoArretramento" #define MSG_AUTORETRACT "AutoArretramento"
#define MSG_FILAMENTCHANGE "Cambia filamento" #define MSG_FILAMENT_CHANGE "Cambia filamento"
#define MSG_INIT_SDCARD "Iniz. SD-Card" #define MSG_INIT_SDCARD "Iniz. SD-Card"
#define MSG_CNG_SDCARD "Cambia SD-Card" #define MSG_CNG_SDCARD "Cambia SD-Card"
#define MSG_ZPROBE_OUT "Z probe out. bed" #define MSG_ZPROBE_OUT "Z probe out. bed"
...@@ -184,6 +206,30 @@ ...@@ -184,6 +206,30 @@
#define MSG_DELTA_CALIBRATE_CENTER "Calibra Centro" #define MSG_DELTA_CALIBRATE_CENTER "Calibra Centro"
#endif // DELTA #endif // DELTA
// FILAMENT_CHANGE_FEATURE
#define MSG_FILAMENT_CHANGE_HEADER "CAMBIO FILO"
#define MSG_FILAMENT_CHANGE_INIT_1 "Attendere"
#define MSG_FILAMENT_CHANGE_INIT_2 "per il cambio"
#define MSG_FILAMENT_CHANGE_INIT_3 "filamento"
#define MSG_FILAMENT_CHANGE_UNLOAD_1 "Attendere lo"
#define MSG_FILAMENT_CHANGE_UNLOAD_2 "scarico filamento"
#define MSG_FILAMENT_CHANGE_UNLOAD_3 ""
#define MSG_FILAMENT_CHANGE_INSERT_1 "Inserire filamento"
#define MSG_FILAMENT_CHANGE_INSERT_2 "premere il bottone"
#define MSG_FILAMENT_CHANGE_INSERT_3 "per continuare..."
#define MSG_FILAMENT_CHANGE_LOAD_1 "Attendere il"
#define MSG_FILAMENT_CHANGE_LOAD_2 "caricamento filo"
#define MSG_FILAMENT_CHANGE_LOAD_3 ""
#define MSG_FILAMENT_CHANGE_EXTRUDE_1 "Attendere"
#define MSG_FILAMENT_CHANGE_EXTRUDE_2 "estrusione filamento"
#define MSG_FILAMENT_CHANGE_EXTRUDE_3 ""
#define MSG_FILAMENT_CHANGE_OPTION_HEADER "Cosa faccio?"
#define MSG_FILAMENT_CHANGE_OPTION_EXTRUDE "Estrudere ancora"
#define MSG_FILAMENT_CHANGE_OPTION_RESUME "Riprendere la stampa"
#define MSG_FILAMENT_CHANGE_RESUME_1 "Attendere che la"
#define MSG_FILAMENT_CHANGE_RESUME_2 "stampa riprenda"
#define MSG_FILAMENT_CHANGE_RESUME_3 ""
// Scara // Scara
#if MECH(SCARA) #if MECH(SCARA)
#define MSG_SCALE "Scale" #define MSG_SCALE "Scale"
......
MK/module/language/language_kana.h
View file @ e5722514
/**
* MK & MK4due 3D Printer Firmware
*
* Based on Marlin, Sprinter and grbl
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
* Copyright (C) 2013 - 2016 Alberto Cotronei @MagoKimbra
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/** /**
* Japanese (Kana) * Japanese (Kana)
* *
......
MK/module/language/language_kana_utf8.h
View file @ e5722514
/**
* MK & MK4due 3D Printer Firmware
*
* Based on Marlin, Sprinter and grbl
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
* Copyright (C) 2013 - 2016 Alberto Cotronei @MagoKimbra
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/** /**
* Japanese (Kana UTF8 version) * Japanese (Kana UTF8 version)
* *
......
MK/module/language/language_nl.h
View file @ e5722514
/**
* MK & MK4due 3D Printer Firmware
*
* Based on Marlin, Sprinter and grbl
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
* Copyright (C) 2013 - 2016 Alberto Cotronei @MagoKimbra
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/** /**
* Dutch * Dutch
* *
......
MK/module/language/language_pl.h
View file @ e5722514
/**
* MK & MK4due 3D Printer Firmware
*
* Based on Marlin, Sprinter and grbl
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
* Copyright (C) 2013 - 2016 Alberto Cotronei @MagoKimbra
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/** /**
* Polish * Polish
* *
......
MK/module/language/language_pt-br.h
View file @ e5722514
/**
* MK & MK4due 3D Printer Firmware
*
* Based on Marlin, Sprinter and grbl
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
* Copyright (C) 2013 - 2016 Alberto Cotronei @MagoKimbra
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/** /**
* Portuguese (Brazil) * Portuguese (Brazil)
* *
......
MK/module/language/language_pt-br_utf8.h 0 → 100644
View file @ e5722514
/**
* MK & MK4due 3D Printer Firmware
*
* Based on Marlin, Sprinter and grbl
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
* Copyright (C) 2013 - 2016 Alberto Cotronei @MagoKimbra
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* Portuguese (Brazil)
*
* LCD Menu Messages
* See also documentation/LCDLanguageFont.md
*
*/
#ifndef LANGUAGE_PT_BR_UTF_H
#define LANGUAGE_PT_BR_UTF_H
#define MAPPER_NON
// Define SIMULATE_ROMFONT to see what is seen on the character based display defined in Configuration.h
//#define SIMULATE_ROMFONT
#define DISPLAY_CHARSET_ISO10646_1
#define WELCOME_MSG MACHINE_NAME " pronto."
#define MSG_SD_INSERTED "Cartão inserido"
#define MSG_SD_REMOVED "Cartão removido"
#define MSG_MAIN "Menu principal"
#define MSG_AUTOSTART "Autostart"
#define MSG_DISABLE_STEPPERS "Desabi. motores"
#define MSG_AUTO_HOME "Ir para origen"
#define MSG_LEVEL_BED_HOMING "Indo para origem"
#define MSG_LEVEL_BED_WAITING "Click to Begin"
#define MSG_LEVEL_BED_DONE "Leveling Done!"
#define MSG_LEVEL_BED_CANCEL "Cancel"
#define MSG_SET_HOME_OFFSETS "Ajustar Jogo"
#define MSG_HOME_OFFSETS_APPLIED "Offsets applied"
#define MSG_SET_ORIGIN "Ajustar orig."
#define MSG_PREHEAT_PLA "Pre-aquecer PLA"
#define MSG_PREHEAT_PLA_N "Pre-aquecer PLA"
#define MSG_PREHEAT_PLA_ALL "Pre-aq.Todo PLA"
#define MSG_PREHEAT_PLA_BEDONLY "Pre-aq. PLA " LCD_STR_THERMOMETER "Base"
#define MSG_PREHEAT_PLA_SETTINGS "Ajustar PLA"
#define MSG_PREHEAT_ABS "Pre-aquecer ABS"
#define MSG_PREHEAT_ABS_N "Pre-aquecer ABS"
#define MSG_PREHEAT_ABS_ALL "Pre-aq.Todo ABS"
#define MSG_PREHEAT_ABS_BEDONLY "Pre-aq. ABS " LCD_STR_THERMOMETER "Base"
#define MSG_PREHEAT_ABS_SETTINGS "Ajustar ABS"
#define MSG_COOLDOWN "Esfriar"
#define MSG_SWITCH_PS_ON "Ligar"
#define MSG_SWITCH_PS_OFF "Desligar"
#define MSG_EXTRUDE "Extrudar"
#define MSG_RETRACT "Retrair"
#define MSG_MOVE_AXIS "Mover eixo"
#define MSG_MOVE_X "Mover X"
#define MSG_MOVE_Y "Mover Y"
#define MSG_MOVE_Z "Mover Z"
#define MSG_MOVE_E "Mover Extrusor"
#define MSG_MOVE_01MM "Mover 0.1mm"
#define MSG_MOVE_1MM "Mover 1mm"
#define MSG_MOVE_10MM "Mover 10mm"
#define MSG_SPEED "Velocidade"
#define MSG_BED_Z "Base Z"
#define MSG_NOZZLE LCD_STR_THERMOMETER " Bocal"
#define MSG_BED LCD_STR_THERMOMETER " Base"
#define MSG_FAN_SPEED "Vel. Ventoinha"
#define MSG_FLOW "Fluxo"
#define MSG_CONTROL "Controle"
#define MSG_MIN LCD_STR_THERMOMETER " Min"
#define MSG_MAX LCD_STR_THERMOMETER " Max"
#define MSG_FACTOR LCD_STR_THERMOMETER " Fact"
#define MSG_AUTOTEMP "Temp. Automática"
#define MSG_ON "Ligado "
#define MSG_OFF "Desligado"
#define MSG_PID_P "PID-P"
#define MSG_PID_I "PID-I"
#define MSG_PID_D "PID-D"
#define MSG_PID_C "PID-C"
#define MSG_ACC "Acc"
#define MSG_VXY_JERK "jogo VXY"
#define MSG_VZ_JERK "jogo VZ"
#define MSG_VE_JERK "jogo VE"
#define MSG_VMAX " Vmax "
#define MSG_X "X"
#define MSG_Y "Y"
#define MSG_Z "Z"
#define MSG_E "E"
#define MSG_VMIN "Vmin"
#define MSG_VTRAV_MIN "VTrav min"
#define MSG_AMAX "Amax "
#define MSG_A_RETRACT "Retrair A"
#define MSG_A_TRAVEL "A-movimento"
#define MSG_XSTEPS "Passo X/mm"
#define MSG_YSTEPS "Passo Y/mm"
#define MSG_ZSTEPS "Passo Z/mm"
#define MSG_ESTEPS "E/mm"
#define MSG_TEMPERATURE "Temperatura"
#define MSG_MOTION "Movimento"
#define MSG_VOLUMETRIC "Filamento"
#define MSG_VOLUMETRIC_ENABLED "Extr. em mm3"
#define MSG_FILAMENT_DIAM "Diametro Fil."
#define MSG_CONTRAST "Contraste"
#define MSG_STORE_EPROM "Salvar"
#define MSG_LOAD_EPROM "Ler"
#define MSG_RESTORE_FAILSAFE "Rest. de emerg."
#define MSG_REFRESH LCD_STR_REFRESH " Restaurar"
#define MSG_WATCH "Monitorar"
#define MSG_PREPARE "Preparar"
#define MSG_TUNE "Afinar"
#define MSG_PAUSE_PRINT "Pausar impressão"
#define MSG_RESUME_PRINT "Resumir impressão"
#define MSG_STOP_PRINT "Parar impressão"
#define MSG_CARD_MENU "Imprimir do SD"
#define MSG_NO_CARD "Sem cartão SD"
#define MSG_DWELL "Repouso..."
#define MSG_USERWAIT "Esperando ordem"
#define MSG_RESUMING "Resumindo Impres."
#define MSG_PRINT_ABORTED "Impres. Abortada."
#define MSG_NO_MOVE "Sem movimento"
#define MSG_KILLED "PARADA DE EMERG."
#define MSG_STOPPED "PARADA. "
#define MSG_CONTROL_RETRACT "Retrair mm"
#define MSG_CONTROL_RETRACT_SWAP "Retrair Troca mm"
#define MSG_CONTROL_RETRACTF "Retrair V"
#define MSG_CONTROL_RETRACT_ZLIFT "Levantar mm"
#define MSG_CONTROL_RETRACT_RECOVER "Des Retrair +mm"
#define MSG_CONTROL_RETRACT_RECOVER_SWAP "Des RetTroca +mm"
#define MSG_CONTROL_RETRACT_RECOVERF "Des Retrair V"
#define MSG_AUTORETRACT "Retração Autom."
#define MSG_FILAMENTCHANGE "Trocar Filamento"
#define MSG_INIT_SDCARD "Iniciar SD"
#define MSG_CNG_SDCARD "Trocar SD"
#define MSG_ZPROBE_OUT "Son. fora da mesa"
#define MSG_YX_UNHOMED "Pos. Desconhecida"
#define MSG_ZPROBE_ZOFFSET "Deslocamento no Z"
#define MSG_BABYSTEP_X "Passinho X"
#define MSG_BABYSTEP_Y "Passinho Y"
#define MSG_BABYSTEP_Z "Passinho Z"
#define MSG_ENDSTOP_ABORT "Fim de Curso"
#define MSG_HEATING_FAILED_LCD "Aquecimento falhou"
#define MSG_ERR_REDUNDANT_TEMP "Err: REDUNDANT TEMP"
#define MSG_THERMAL_RUNAWAY "THERMAL RUNAWAY"
#define MSG_ERR_MAXTEMP "Err: T Máxima"
#define MSG_ERR_MINTEMP "Err: T Mínima"
#define MSG_ERR_MAXTEMP_BED "Err: T Base Máxima"
#define MSG_ERR_MINTEMP_BED "Err: T Base Mínima"
#define MSG_END_HOUR "Horas"
#define MSG_END_MINUTE "Minutos"
#define MSG_HEATING "Aquecendo..."
#define MSG_HEATING_COMPLETE "Aquecida."
#define MSG_BED_HEATING "Aquecendo base.."
#define MSG_BED_DONE "Base aquecida."
#define MSG_DELTA_CALIBRATE "Calibrar Delta"
#define MSG_DELTA_CALIBRATE_X "Calibrar X"
#define MSG_DELTA_CALIBRATE_Y "Calibrar Y"
#define MSG_DELTA_CALIBRATE_Z "Calibrar Z"
#define MSG_DELTA_CALIBRATE_CENTER "Calibrar Centro"
#endif // LANGUAGE_PT_BR_UTF_H
MK/module/language/language_pt.h
View file @ e5722514
/**
* MK & MK4due 3D Printer Firmware
*
* Based on Marlin, Sprinter and grbl
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
* Copyright (C) 2013 - 2016 Alberto Cotronei @MagoKimbra
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/** /**
* Portuguese * Portuguese
* *
......
MK/module/language/language_pt_utf8.h 0 → 100644
View file @ e5722514
/**
* MK & MK4due 3D Printer Firmware
*
* Based on Marlin, Sprinter and grbl
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
* Copyright (C) 2013 - 2016 Alberto Cotronei @MagoKimbra
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* Portuguese
*
* LCD Menu Messages
* See also documentation/LCDLanguageFont.md
*
*/
#ifndef LANGUAGE_PT_UTF_H
#define LANGUAGE_PT_UTF_H
#define MAPPER_NON
// Define SIMULATE_ROMFONT to see what is seen on the character based display defined in Configuration.h
//#define SIMULATE_ROMFONT
#define DISPLAY_CHARSET_ISO10646_1
#define WELCOME_MSG MACHINE_NAME " pronto."
#define MSG_SD_INSERTED "Cartão inserido"
#define MSG_SD_REMOVED "Cartão removido"
#define MSG_MAIN "Menu principal"
#define MSG_AUTOSTART "Autostart"
#define MSG_DISABLE_STEPPERS "Desactivar motores"
#define MSG_AUTO_HOME "Ir para origem"
#define MSG_LEVEL_BED_HOMING "Indo para origem"
#define MSG_LEVEL_BED_WAITING "Click to Begin"
#define MSG_LEVEL_BED_DONE "Leveling Done!"
#define MSG_LEVEL_BED_CANCEL "Cancel"
#define MSG_SET_HOME_OFFSETS "Definir desvio"
#define MSG_HOME_OFFSETS_APPLIED "Offsets applied"
#define MSG_SET_ORIGIN "Definir origem"
#define MSG_PREHEAT_PLA "Pre-aquecer PLA"
#define MSG_PREHEAT_PLA_N "Pre-aquecer PLA"
#define MSG_PREHEAT_PLA_ALL "Pre-aq. PLA Tudo"
#define MSG_PREHEAT_PLA_BEDONLY "Pre-aq. PLA " LCD_STR_THERMOMETER "Base"
#define MSG_PREHEAT_PLA_SETTINGS "Definições PLA"
#define MSG_PREHEAT_ABS "Pre-aquecer ABS"
#define MSG_PREHEAT_ABS_N "Pre-aquecer ABS "
#define MSG_PREHEAT_ABS_ALL "Pre-aq. ABS Tudo"
#define MSG_PREHEAT_ABS_BEDONLY "Pre-aq. ABS " LCD_STR_THERMOMETER "Base"
#define MSG_PREHEAT_ABS_SETTINGS "Definições ABS"
#define MSG_COOLDOWN "Arrefecer"
#define MSG_SWITCH_PS_ON "Ligar"
#define MSG_SWITCH_PS_OFF "Desligar"
#define MSG_EXTRUDE "Extrudir"
#define MSG_RETRACT "Retrair"
#define MSG_MOVE_AXIS "Mover eixo"
#define MSG_MOVE_X "Mover X"
#define MSG_MOVE_Y "Mover Y"
#define MSG_MOVE_Z "Mover Z"
#define MSG_MOVE_E "Mover Extrusor"
#define MSG_MOVE_01MM "Mover 0.1mm"
#define MSG_MOVE_1MM "Mover 1mm"
#define MSG_MOVE_10MM "Mover 10mm"
#define MSG_SPEED "Velocidade"
#define MSG_BED_Z "Base Z"
#define MSG_NOZZLE LCD_STR_THERMOMETER " Bico"
#define MSG_BED LCD_STR_THERMOMETER " Base"
#define MSG_FAN_SPEED "Vel. ventoinha"
#define MSG_FLOW "Fluxo"
#define MSG_CONTROL "Controlo"
#define MSG_MIN LCD_STR_THERMOMETER " Min"
#define MSG_MAX LCD_STR_THERMOMETER " Max"
#define MSG_FACTOR LCD_STR_THERMOMETER " Fact"
#define MSG_AUTOTEMP "Temp. Automática"
#define MSG_ON "On "
#define MSG_OFF "Off"
#define MSG_PID_P "PID-P"
#define MSG_PID_I "PID-I"
#define MSG_PID_D "PID-D"
#define MSG_PID_C "PID-C"
#define MSG_E1 "E1"
#define MSG_E2 "E2"
#define MSG_E3 "E3"
#define MSG_E4 "E4"
#define MSG_ACC "Acc"
#define MSG_VXY_JERK "Vxy-jerk"
#define MSG_VZ_JERK "Vz-jerk"
#define MSG_VE_JERK "Ve-jerk"
#define MSG_VMAX " Vmax "
#define MSG_X "X"
#define MSG_Y "Y"
#define MSG_Z "Z"
#define MSG_E "E"
#define MSG_VMIN "Vmin"
#define MSG_VTRAV_MIN "VTrav min"
#define MSG_AMAX "Amax "
#define MSG_A_RETRACT "A-retracção"
#define MSG_A_TRAVEL "A-movimento"
#define MSG_XSTEPS "X passo/mm"
#define MSG_YSTEPS "Y passo/mm"
#define MSG_ZSTEPS "Z passo/mm"
#define MSG_ESTEPS "E passo/mm"
#define MSG_TEMPERATURE "Temperatura"
#define MSG_MOTION "Movimento"
#define MSG_VOLUMETRIC "Filamento"
#define MSG_VOLUMETRIC_ENABLED "E em mm3"
#define MSG_FILAMENT_DIAM "Fil. Diam."
#define MSG_CONTRAST "Contraste"
#define MSG_STORE_EPROM "Guardar na memoria"
#define MSG_LOAD_EPROM "Carregar da memoria"
#define MSG_RESTORE_FAILSAFE "Rest. de emergen."
#define MSG_REFRESH LCD_STR_REFRESH " Recarregar"
#define MSG_WATCH "Monitorizar"
#define MSG_PREPARE "Preparar"
#define MSG_TUNE "Afinar"
#define MSG_PAUSE_PRINT "Pausar impressão"
#define MSG_RESUME_PRINT "Retomar impressão"
#define MSG_STOP_PRINT "Parar impressão"
#define MSG_CARD_MENU "Imprimir do SD"
#define MSG_NO_CARD "Sem cartão SD"
#define MSG_DWELL "Em espera..."
#define MSG_USERWAIT "Á espera de ordem"
#define MSG_RESUMING "Retomando impressão"
#define MSG_PRINT_ABORTED "Impressão cancelada"
#define MSG_NO_MOVE "Sem movimento"
#define MSG_KILLED "EMERGÊNCIA. "
#define MSG_STOPPED "PARADO. "
#define MSG_CONTROL_RETRACT " Retrair mm"
#define MSG_CONTROL_RETRACT_SWAP "Troca Retrair mm"
#define MSG_CONTROL_RETRACTF " Retrair V"
#define MSG_CONTROL_RETRACT_ZLIFT " Levantar mm"
#define MSG_CONTROL_RETRACT_RECOVER " DesRet +mm"
#define MSG_CONTROL_RETRACT_RECOVER_SWAP "Troca DesRet +mm"
#define MSG_CONTROL_RETRACT_RECOVERF " DesRet V"
#define MSG_AUTORETRACT " AutoRetr."
#define MSG_FILAMENTCHANGE "Trocar filamento"
#define MSG_INIT_SDCARD "Inici. cartão SD"
#define MSG_CNG_SDCARD "Trocar cartão SD"
#define MSG_ZPROBE_OUT "Sensor fora/base"
#define MSG_YX_UNHOMED "XY antes de Z"
#define MSG_ZPROBE_ZOFFSET "Desvio Z"
#define MSG_BABYSTEP_X "Babystep X"
#define MSG_BABYSTEP_Y "Babystep Y"
#define MSG_BABYSTEP_Z "Babystep Z"
#define MSG_ENDSTOP_ABORT "Fim de curso"
#define MSG_HEATING_FAILED_LCD "Aquecimento falhou"
#define MSG_ERR_REDUNDANT_TEMP "Err: REDUNDANT TEMP"
#define MSG_THERMAL_RUNAWAY "THERMAL RUNAWAY"
#define MSG_ERR_MAXTEMP "Err: T Máxima"
#define MSG_ERR_MINTEMP "Err: T Mínima"
#define MSG_ERR_MAXTEMP_BED "Err: T Base Máxima"
#define MSG_ERR_MINTEMP_BED "Err: T Base Mínima"
#define MSG_END_HOUR "horas"
#define MSG_END_MINUTE "minutos"
#define MSG_HEATING "Aquecendo..."
#define MSG_HEATING_COMPLETE "Aquecida."
#define MSG_BED_HEATING "Aquecendo base.."
#define MSG_BED_DONE "Base aquecida."
#define MSG_DELTA_CALIBRATE "Calibração Delta"
#define MSG_DELTA_CALIBRATE_X "Calibrar X"
#define MSG_DELTA_CALIBRATE_Y "Calibrar Y"
#define MSG_DELTA_CALIBRATE_Z "Calibrar Z"
#define MSG_DELTA_CALIBRATE_CENTER "Calibrar Centro"
#endif // LANGUAGE_PT_UTF_H
MK/module/language/language_ru.h
View file @ e5722514
/**
* MK & MK4due 3D Printer Firmware
*
* Based on Marlin, Sprinter and grbl
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
* Copyright (C) 2013 - 2016 Alberto Cotronei @MagoKimbra
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/** /**
* Russian * Russian
* *
......
MK/module/lcd/ultralcd.cpp
View file @ e5722514
...@@ -110,6 +110,16 @@ static void lcd_status_screen(); ...@@ -110,6 +110,16 @@ static void lcd_status_screen();
static void lcd_control_motion_menu(); static void lcd_control_motion_menu();
static void lcd_control_volumetric_menu(); static void lcd_control_volumetric_menu();
#if ENABLED(FILAMENT_CHANGE_FEATURE)
static void lcd_filament_change_option_menu();
static void lcd_filament_change_init_message();
static void lcd_filament_change_unload_message();
static void lcd_filament_change_insert_message();
static void lcd_filament_change_load_message();
static void lcd_filament_change_extrude_message();
static void lcd_filament_change_resume_message();
#endif
#if HAS(LCD_CONTRAST) #if HAS(LCD_CONTRAST)
static void lcd_set_contrast(); static void lcd_set_contrast();
#endif #endif
...@@ -786,8 +796,8 @@ static void lcd_tune_menu() { ...@@ -786,8 +796,8 @@ static void lcd_tune_menu() {
// //
// Change filament // Change filament
// //
#if ENABLED(FILAMENTCHANGEENABLE) #if ENABLED(FILAMENT_CHANGE_FEATURE)
MENU_ITEM(gcode, MSG_FILAMENTCHANGE, PSTR("M600")); MENU_ITEM(gcode, MSG_FILAMENT_CHANGE, PSTR("M600"));
#endif #endif
END_MENU(); END_MENU();
...@@ -1756,6 +1766,117 @@ static void lcd_control_volumetric_menu() { ...@@ -1756,6 +1766,117 @@ static void lcd_control_volumetric_menu() {
#endif // SDSUPPORT #endif // SDSUPPORT
#if ENABLED(FILAMENT_CHANGE_FEATURE)
static void lcd_filament_change_nothing() {
}
static void lcd_filament_change_resume_print() {
filament_change_menu_response = FILAMENT_CHANGE_RESPONSE_RESUME_PRINT;
lcdDrawUpdate = 2;
lcd_goto_menu(lcd_status_screen);
}
static void lcd_filament_change_extrude_more() {
filament_change_menu_response = FILAMENT_CHANGE_RESPONSE_EXTRUDE_MORE;
}
static void lcd_filament_change_option_menu() {
START_MENU();
MENU_ITEM(function, MSG_FILAMENT_CHANGE_OPTION_HEADER, lcd_filament_change_nothing);
MENU_ITEM(function, MSG_FILAMENT_CHANGE_OPTION_RESUME, lcd_filament_change_resume_print);
MENU_ITEM(function, MSG_FILAMENT_CHANGE_OPTION_EXTRUDE, lcd_filament_change_extrude_more);
END_MENU();
}
static void lcd_filament_change_init_message() {
START_MENU();
MENU_ITEM(function, MSG_FILAMENT_CHANGE_HEADER, lcd_filament_change_nothing);
MENU_ITEM(function, MSG_FILAMENT_CHANGE_INIT_1, lcd_filament_change_nothing);
MENU_ITEM(function, MSG_FILAMENT_CHANGE_INIT_2, lcd_filament_change_nothing);
MENU_ITEM(function, MSG_FILAMENT_CHANGE_INIT_3, lcd_filament_change_nothing);
END_MENU();
}
static void lcd_filament_change_unload_message() {
START_MENU();
MENU_ITEM(function, MSG_FILAMENT_CHANGE_HEADER, lcd_filament_change_nothing);
MENU_ITEM(function, MSG_FILAMENT_CHANGE_UNLOAD_1, lcd_filament_change_nothing);
MENU_ITEM(function, MSG_FILAMENT_CHANGE_UNLOAD_2, lcd_filament_change_nothing);
MENU_ITEM(function, MSG_FILAMENT_CHANGE_UNLOAD_3, lcd_filament_change_nothing);
END_MENU();
}
static void lcd_filament_change_insert_message() {
START_MENU();
MENU_ITEM(function, MSG_FILAMENT_CHANGE_HEADER, lcd_filament_change_nothing);
MENU_ITEM(function, MSG_FILAMENT_CHANGE_INSERT_1, lcd_filament_change_nothing);
MENU_ITEM(function, MSG_FILAMENT_CHANGE_INSERT_2, lcd_filament_change_nothing);
MENU_ITEM(function, MSG_FILAMENT_CHANGE_INSERT_3, lcd_filament_change_nothing);
END_MENU();
}
static void lcd_filament_change_load_message() {
START_MENU();
MENU_ITEM(function, MSG_FILAMENT_CHANGE_HEADER, lcd_filament_change_nothing);
MENU_ITEM(function, MSG_FILAMENT_CHANGE_LOAD_1, lcd_filament_change_nothing);
MENU_ITEM(function, MSG_FILAMENT_CHANGE_LOAD_2, lcd_filament_change_nothing);
MENU_ITEM(function, MSG_FILAMENT_CHANGE_LOAD_3, lcd_filament_change_nothing);
END_MENU();
}
static void lcd_filament_change_extrude_message() {
START_MENU();
MENU_ITEM(function, MSG_FILAMENT_CHANGE_HEADER, lcd_filament_change_nothing);
MENU_ITEM(function, MSG_FILAMENT_CHANGE_EXTRUDE_1, lcd_filament_change_nothing);
MENU_ITEM(function, MSG_FILAMENT_CHANGE_EXTRUDE_2, lcd_filament_change_nothing);
MENU_ITEM(function, MSG_FILAMENT_CHANGE_EXTRUDE_3, lcd_filament_change_nothing);
END_MENU();
}
static void lcd_filament_change_resume_message() {
START_MENU();
MENU_ITEM(function, MSG_FILAMENT_CHANGE_HEADER, lcd_filament_change_nothing);
MENU_ITEM(function, MSG_FILAMENT_CHANGE_RESUME_1, lcd_filament_change_nothing);
MENU_ITEM(function, MSG_FILAMENT_CHANGE_RESUME_2, lcd_filament_change_nothing);
MENU_ITEM(function, MSG_FILAMENT_CHANGE_RESUME_3, lcd_filament_change_nothing);
END_MENU();
}
void lcd_filament_change_show_message(FilamentChangeMessage message) {
switch (message) {
case FILAMENT_CHANGE_MESSAGE_INIT:
defer_return_to_status = true;
lcd_goto_menu(lcd_filament_change_init_message);
break;
case FILAMENT_CHANGE_MESSAGE_UNLOAD:
lcd_goto_menu(lcd_filament_change_unload_message);
break;
case FILAMENT_CHANGE_MESSAGE_INSERT:
lcd_goto_menu(lcd_filament_change_insert_message);
break;
case FILAMENT_CHANGE_MESSAGE_LOAD:
lcd_goto_menu(lcd_filament_change_load_message);
break;
case FILAMENT_CHANGE_MESSAGE_EXTRUDE:
lcd_goto_menu(lcd_filament_change_extrude_message);
break;
case FILAMENT_CHANGE_MESSAGE_OPTION:
while (lcd_clicked()) idle(true);
filament_change_menu_response = FILAMENT_CHANGE_RESPONSE_WAIT_FOR;
lcd_goto_menu(lcd_filament_change_option_menu);
break;
case FILAMENT_CHANGE_MESSAGE_RESUME:
lcd_goto_menu(lcd_filament_change_resume_message);
break;
case FILAMENT_CHANGE_MESSAGE_STATUS:
lcd_return_to_status();
break;
}
}
#endif // FILAMENT_CHANGE_FEATURE
/** /**
* *
* Functions for editing single values * Functions for editing single values
......
MK/module/lcd/ultralcd.h
View file @ e5722514
...@@ -68,6 +68,19 @@ ...@@ -68,6 +68,19 @@
#if ENABLED(ULTIPANEL) #if ENABLED(ULTIPANEL)
void lcd_buttons_update(); void lcd_buttons_update();
extern volatile uint8_t buttons; // the last checked buttons in a bit array. extern volatile uint8_t buttons; // the last checked buttons in a bit array.
#if ENABLED(FILAMENT_CHANGE_FEATURE)
enum FilamentChangeMessage {
FILAMENT_CHANGE_MESSAGE_INIT,
FILAMENT_CHANGE_MESSAGE_UNLOAD,
FILAMENT_CHANGE_MESSAGE_INSERT,
FILAMENT_CHANGE_MESSAGE_LOAD,
FILAMENT_CHANGE_MESSAGE_EXTRUDE,
FILAMENT_CHANGE_MESSAGE_OPTION,
FILAMENT_CHANGE_MESSAGE_RESUME,
FILAMENT_CHANGE_MESSAGE_STATUS
};
void lcd_filament_change_show_message(FilamentChangeMessage message);
#endif
#else #else
FORCE_INLINE void lcd_buttons_update() {} FORCE_INLINE void lcd_buttons_update() {}
#endif #endif
......
MK/module/motion/endstops.cpp
View file @ e5722514
...@@ -321,7 +321,7 @@ void Endstops::update() { ...@@ -321,7 +321,7 @@ void Endstops::update() {
#endif // !Z_DUAL_ENDSTOPS #endif // !Z_DUAL_ENDSTOPS
#endif // HAS_Z_MIN #endif // HAS_Z_MIN
#if ENABLED(Z_PROBE_ENDSTOP) #if HAS(Z_PROBE)
if (z_probe_enabled) { if (z_probe_enabled) {
UPDATE_ENDSTOP(Z, PROBE); UPDATE_ENDSTOP(Z, PROBE);
if (TEST_ENDSTOP(Z_PROBE)) SBI(endstop_hit_bits, Z_PROBE); if (TEST_ENDSTOP(Z_PROBE)) SBI(endstop_hit_bits, Z_PROBE);
......
MK/module/motion/endstops.h
View file @ e5722514
...@@ -68,7 +68,7 @@ class Endstops { ...@@ -68,7 +68,7 @@ class Endstops {
/** /**
* Print an error message reporting the position when the endstops were last hit. * Print an error message reporting the position when the endstops were last hit.
*/ */
void report_state(); //call from somewhere to create an serial error message with the locations the endstops where hit, in case they were triggered void report_state(); // call from somewhere to create an serial error message with the locations the endstops where hit, in case they were triggered
/** /**
* Report endstop positions in response to M119 * Report endstop positions in response to M119
......
MK/module/sanitycheck.h
View file @ e5722514
...@@ -406,24 +406,24 @@ ...@@ -406,24 +406,24 @@
#endif #endif
#endif #endif
#if ENABLED(FILAMENTCHANGEENABLE) #if ENABLED(FILAMENT_CHANGE_FEATURE)
#if DISABLED(FILAMENTCHANGE_XPOS) #if DISABLED(FILAMENT_CHANGE_X_POS)
#error DEPENDENCY ERROR: Missing setting FILAMENTCHANGE_XPOS #error DEPENDENCY ERROR: Missing setting FILAMENT_CHANGE_X_POS
#endif #endif
#if DISABLED(FILAMENTCHANGE_YPOS) #if DISABLED(FILAMENT_CHANGE_Y_POS)
#error DEPENDENCY ERROR: Missing setting FILAMENTCHANGE_YPOS #error DEPENDENCY ERROR: Missing setting FILAMENT_CHANGE_Y_POS
#endif #endif
#if DISABLED(FILAMENTCHANGE_ZADD) #if DISABLED(FILAMENT_CHANGE_Z_ADD)
#error DEPENDENCY ERROR: Missing setting FILAMENTCHANGE_ZADD #error DEPENDENCY ERROR: Missing setting FILAMENT_CHANGE_Z_ADD
#endif #endif
#if DISABLED(FILAMENTCHANGE_FIRSTRETRACT) #if DISABLED(FILAMENT_CHANGE_RETRACT_LENGTH)
#error DEPENDENCY ERROR: Missing setting FILAMENTCHANGE_FIRSTRETRACT #error DEPENDENCY ERROR: Missing setting FILAMENT_CHANGE_RETRACT_LENGTH
#endif #endif
#if DISABLED(FILAMENTCHANGE_FINALRETRACT) #if DISABLED(FILAMENT_CHANGE_UNLOAD_LENGTH)
#error DEPENDENCY ERROR: Missing setting FILAMENTCHANGE_FINALRETRACT #error DEPENDENCY ERROR: Missing setting FILAMENT_CHANGE_UNLOAD_LENGTH
#endif #endif
#if DISABLED(FILAMENTCHANGE_PRINTEROFF) #if DISABLED(FILAMENT_CHANGE_PRINTER_OFF)
#error DEPENDENCY ERROR: Missing setting FILAMENTCHANGE_PRINTEROFF #error DEPENDENCY ERROR: Missing setting FILAMENT_CHANGE_PRINTER_OFF
#endif #endif
#endif #endif
...@@ -1472,10 +1472,10 @@ ...@@ -1472,10 +1472,10 @@
#endif #endif
/** /**
* Required LCD for FILAMENTCHANGEENABLE * Required LCD for FILAMENT_CHANGE_FEATURE
*/ */
#if ENABLED(FILAMENTCHANGEENABLE) && DISABLED(ULTRA_LCD) #if ENABLED(FILAMENT_CHANGE_FEATURE) && DISABLED(ULTRA_LCD)
#error DEPENDENCY ERROR: You must have LCD in order to use FILAMENTCHANGEENABLE #error DEPENDENCY ERROR: You must have LCD in order to use FILAMENT_CHANGE_FEATURE
#endif #endif
/** /**
......
MK/module/temperature/temperature.cpp
View file @ e5722514
...@@ -97,14 +97,14 @@ unsigned char soft_pwm_bed; ...@@ -97,14 +97,14 @@ unsigned char soft_pwm_bed;
#endif #endif
#if ENABLED(THERMAL_PROTECTION_HOTENDS) || ENABLED(THERMAL_PROTECTION_BED) #if ENABLED(THERMAL_PROTECTION_HOTENDS) || ENABLED(THERMAL_PROTECTION_BED)
enum TRState { TRReset, TRInactive, TRFirstHeating, TRStable, TRRunaway }; enum TRState { TRInactive, TRFirstHeating, TRStable, TRRunaway };
void thermal_runaway_protection(TRState* state, millis_t* timer, float temperature, float target_temperature, int heater_id, int period_seconds, int hysteresis_degc); void thermal_runaway_protection(TRState* state, millis_t* timer, float temperature, float target_temperature, int heater_id, int period_seconds, int hysteresis_degc);
#if ENABLED(THERMAL_PROTECTION_HOTENDS) #if ENABLED(THERMAL_PROTECTION_HOTENDS)
static TRState thermal_runaway_state_machine[HOTENDS] = { TRReset }; static TRState thermal_runaway_state_machine[HOTENDS] = { TRInactive };
static millis_t thermal_runaway_timer[HOTENDS] = { 0 }; static millis_t thermal_runaway_timer[HOTENDS] = { 0 };
#endif #endif
#if ENABLED(THERMAL_PROTECTION_BED) && TEMP_SENSOR_BED != 0 #if ENABLED(THERMAL_PROTECTION_BED) && TEMP_SENSOR_BED != 0
static TRState thermal_runaway_bed_state_machine = TRReset; static TRState thermal_runaway_bed_state_machine = TRInactive;
static millis_t thermal_runaway_bed_timer; static millis_t thermal_runaway_bed_timer;
#endif #endif
#endif #endif
...@@ -1284,33 +1284,26 @@ void tp_init() { ...@@ -1284,33 +1284,26 @@ void tp_init() {
int heater_index = heater_id >= 0 ? heater_id : HOTENDS; int heater_index = heater_id >= 0 ? heater_id : HOTENDS;
// If the target temperature changes, restart // If the target temperature changes, restart
if (tr_target_temperature[heater_index] != target_temperature) if (tr_target_temperature[heater_index] != target_temperature) {
*state = TRReset; tr_target_temperature[heater_index] = target_temperature;
*state = target_temperature > 0 ? TRFirstHeating : TRInactive;
}
switch (*state) { switch (*state) {
case TRReset:
*timer = 0;
*state = TRInactive;
// Inactive state waits for a target temperature to be set // Inactive state waits for a target temperature to be set
case TRInactive: case TRInactive: break;
if (target_temperature > 0) {
tr_target_temperature[heater_index] = target_temperature;
*state = TRFirstHeating;
}
break;
// When first heating, wait for the temperature to be reached then go to Stable state // When first heating, wait for the temperature to be reached then go to Stable state
case TRFirstHeating: case TRFirstHeating:
if (temperature >= tr_target_temperature[heater_index]) *state = TRStable; if (temperature < tr_target_temperature[heater_index]) break;
break; *state = TRStable;
// While the temperature is stable watch for a bad temperature // While the temperature is stable watch for a bad temperature
case TRStable: case TRStable:
// If the temperature is over the target (-hysteresis) restart the timer if (temperature < tr_target_temperature[heater_index] - hysteresis_degc && ELAPSED(millis(), *timer))
if (temperature >= tr_target_temperature[heater_index] - hysteresis_degc)
*timer = millis();
// If the timer goes too long without a reset, trigger shutdown
else if (ELAPSED(millis(), *timer + period_seconds * 1000UL))
*state = TRRunaway; *state = TRRunaway;
break; else {
*timer = millis() + period_seconds * 1000UL;
break;
}
case TRRunaway: case TRRunaway:
_temp_error(heater_id, PSTR(SERIAL_T_THERMAL_RUNAWAY), PSTR(MSG_THERMAL_RUNAWAY)); _temp_error(heater_id, PSTR(SERIAL_T_THERMAL_RUNAWAY), PSTR(MSG_THERMAL_RUNAWAY));
} }
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment