Move laser pins to documentation config

Documentation/Laser/K40_ramps_configs/K40_no_cooler_no_flowmeter/Configuration_Pins.h

@@ -70,7 +70,7 @@
 #define HEATER_3_PIN        ORIG_HEATER_3_PIN
 #define HEATER_BED_PIN      ORIG_HEATER_BED_PIN
 #define HEATER_CHAMBER_PIN  -1
-#define COOLER_PIN          -1
+#define COOLER_PIN          2
 
 // TEMP pin
 #define TEMP_0_PIN        ORIG_TEMP_0_PIN
@@ -108,11 +108,15 @@
 #endif
 
 #if ENABLED(LASERBEAM)
-  #define LASER_PWR_PIN                   -1
-  #define LASER_TTL_PIN                   -1
+  #if LASER_CONTROL == 1
+    #define LASER_PWR_PIN    5
+    #define LASER_TTL_PIN -1
+  #elif LASER_CONTROL == 2
+    #define LASER_PWR_PIN 6
+    #define LASER_TTL_PIN 5
   #if ENABLED(LASER_PERIPHERALS)
-    #define LASER_PERIPHERALS_PIN         -1
-    #define LASER_PERIPHERALS_STATUS_PIN  -1
+    #define LASER_PERIPHERALS_PIN         11
+    #define LASER_PERIPHERALS_STATUS_PIN  14
   #endif
 #endif
 
@@ -125,7 +129,7 @@
 #endif
 
 #if ENABLED(FLOWMETER_SENSOR)
-  #define FLOWMETER_PIN -1
+  #define FLOWMETER_PIN 21
 #endif
 
 #if ENABLED(POWER_CONSUMPTION)

Documentation/Laser/K40_ramps_configs/K40_with_cooler_and_flowmeter/Configuration_Pins.h

@@ -70,7 +70,7 @@
 #define HEATER_3_PIN        ORIG_HEATER_3_PIN
 #define HEATER_BED_PIN      ORIG_HEATER_BED_PIN
 #define HEATER_CHAMBER_PIN  -1
-#define COOLER_PIN          -1
+#define COOLER_PIN          2
 
 // TEMP pin
 #define TEMP_0_PIN        ORIG_TEMP_0_PIN
@@ -108,11 +108,15 @@
 #endif
 
 #if ENABLED(LASERBEAM)
-  #define LASER_PWR_PIN                   -1
-  #define LASER_TTL_PIN                   -1
+  #if LASER_CONTROL == 1
+    #define LASER_PWR_PIN    5
+    #define LASER_TTL_PIN -1
+  #elif LASER_CONTROL == 2
+    #define LASER_PWR_PIN 6
+    #define LASER_TTL_PIN 5
   #if ENABLED(LASER_PERIPHERALS)
-    #define LASER_PERIPHERALS_PIN         -1
-    #define LASER_PERIPHERALS_STATUS_PIN  -1
+    #define LASER_PERIPHERALS_PIN         11
+    #define LASER_PERIPHERALS_STATUS_PIN  14
   #endif
 #endif
 
@@ -125,7 +129,7 @@
 #endif
 
 #if ENABLED(FLOWMETER_SENSOR)
-  #define FLOWMETER_PIN -1
+  #define FLOWMETER_PIN 21
 #endif
 
 #if ENABLED(POWER_CONSUMPTION)

MK/module/boards/301.h

@@ -74,25 +74,6 @@
 #define KILL_PIN           -1 // 80 with Smart Controller LCD
 #define SUICIDE_PIN        -1 // PIN that has to be turned on right after start, to keep power flowing.
 
-#undef LASER_TTL_PIN
-#undef LASER_PWR_PIN
-#if LASER_CONTROL == 1
-   #define LASER_PWR_PIN    5
-   #define LASER_TTL_PIN -1
-#endif
-#if LASER_CONTROL == 2
-   #define LASER_TTL_PIN 5 // Digital pins 2, 3, 5, 6, 7, 8 are attached to timers we can use
-   #define LASER_PWR_PIN   2
-#endif
-
-#if ENABLED(LASER_PERIPHERALS)
-   #undef LASER_PERIPHERALS_PIN
-   #undef LASER_PERIPHERALS_STATUS_PIN
-   #define LASER_PERIPHERALS_PIN       11
-   #define LASER_PERIPHERALS_STATUS_PIN      4
-#endif
-
-
 
 #if ENABLED(ULTRA_LCD)
   #define KILL_PIN 80

MK/module/boards/33.h

@@ -71,36 +71,6 @@
 #define ORIG_TEMP_BED_PIN       14  // ANALOG NUMBERING
 
 
-#if ENABLED(LASERBEAM)
-	#undef LASER_TTL_PIN
-	#undef LASER_PWR_PIN
-	#if LASER_CONTROL == 1
-  		#define LASER_PWR_PIN    5
-  		#define LASER_TTL_PIN -1
-	#endif
-	#if LASER_CONTROL == 2
-   	#define LASER_TTL_PIN 6 // Digital pins 2, 3, 5, 6, 7, 8 are attached to timers we can use
-   	#define LASER_PWR_PIN  5 
-	#endif
-#endif
-#if ENABLED(LASER_PERIPHERALS)
-   #undef LASER_PERIPHERALS_PIN
-   #undef LASER_PERIPHERALS_STATUS_PIN
-   #define LASER_PERIPHERALS_PIN       11
-   #define LASER_PERIPHERALS_STATUS_PIN      4
-#endif
-
-#if ENABLED(PIDTEMPCOOLER)
-   #undef COOLER_PIN
-	#define COOLER_PIN 2
-#endif
-
-#if ENABLED(FLOWMETER_SENSOR)
-  #undef FLOWMETER_PIN
-  #define FLOWMETER_PIN 21
-#endif
-
-
 #if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER) || ENABLED(G3D_PANEL)
   #define KILL_PIN              41
 #else