add pins2tool

MarlinKimbra/Configuration.h

@@ -126,31 +126,7 @@
 
 //**********************************************************************
 
-/***********************************************************************
- *********************** Multiextruder NPr2  ***************************
- ***********************************************************************
- *                                                                     *
- * Setting fot color meccanism NPr2 by NicolaP (www.3dmakerlab.it)     *
- *                                                                     *
- * Firmware by MagoKimbra magokimbra@hotmail.com                       *
- *                                                                     *
- * Find angle setting by g-Code "M997 Cxxx"                            *
- *                                                                     *
- ***********************************************************************/
-//#define NPR2
-#ifdef NPR2
-#define COLOR_STEP {120, 25, -65, -155}           // CARTER ANGLE
-#define COLOR_SLOWRATE 170                        // MICROSECOND delay for carter motor routine (Carter Motor Feedrate: upper value-slow feedrate)  
-#define COLOR_HOMERATE 4                          // FEEDRATE for carter home
-#define MOTOR_ANGLE 1.8                           // Nema angle for single step 
-#define DRIVER_MICROSTEP 4                        // Microstep moltiplicator driver (set jumper MS1-2-3) off-on-off 1/4 microstepping.
-#define CARTER_MOLTIPLICATOR 14.22                // CARTER MOLTIPLICATOR (gear ratio 13/31-10/31)
-#define DRIVER_EXTRUDERS 2                        // This defines the number of Driver extruders
-#endif
-//**********************************************************************
-
-
-#if !defined(MKR4) && !defined(NPR2)
+#if !defined(MKR4)
 #define DRIVER_EXTRUDERS EXTRUDERS // This defines the number of Driver extruders
 #endif
 
@@ -187,7 +163,7 @@
  * 10 is 100k RS thermistor 198-961 (4.7k pullup)
  * 11 is 100k beta 3950 1% thermistor (4.7k pullup)
  * 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- * 13 is 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" 
+ * 13 is 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" 
  * 20 is the PT100 circuit found in the Ultimainboard V2.x
  * 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  * 

MarlinKimbra/Configuration_Corexy.h

@@ -220,3 +220,15 @@ const bool Z_MAX_ENDSTOP_INVERTING = false;      // set to true to invert the lo
 #define DEFAULT_XYJERK 10.0    // (mm/sec)
 #define DEFAULT_ZJERK 0.4      // (mm/sec)
 #define DEFAULT_EJERK 5.0      // (mm/sec)
+
+//===========================================================================
+//=============================Additional Features===========================
+//===========================================================================
+
+// Custom M code points
+//#define CUSTOM_M_CODES
+#ifdef CUSTOM_M_CODES
+#define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
+#define Z_PROBE_OFFSET_RANGE_MIN -15
+#define Z_PROBE_OFFSET_RANGE_MAX -5
+#endif
\ No newline at end of file

MarlinKimbra/pins.h

@@ -3110,8 +3110,10 @@ DaveX plan for Teensylu/printrboard-type pinouts (ref teensylu & sprinter) for a
 #define TEMP_3_PIN ORIG_TEMP_3_PIN
 #define TEMP_BED_PIN ORIG_TEMP_BED_PIN
 
-#define SENSITIVE_PINS {0, 1, ORIG_X_STEP_PIN, ORIG_X_DIR_PIN, ORIG_X_ENABLE_PIN, ORIG_X_MIN_PIN, ORIG_X_MAX_PIN, ORIG_Y_STEP_PIN, ORIG_Y_DIR_PIN, ORIG_Y_ENABLE_PIN, ORIG_Y_MIN_PIN, ORIG_Y_MAX_PIN, ORIG_Z_STEP_PIN, ORIG_Z_DIR_PIN, ORIG_Z_ENABLE_PIN, ORIG_Z_MIN_PIN, ORIG_Z_MAX_PIN, PS_ON_PIN, \
+#include "pins2tool.h"
+
+#define SENSITIVE_PINS {0, 1, X_STEP_PIN, X_DIR_PIN, X_ENABLE_PIN, X_MIN_PIN, X_MAX_PIN, Y_STEP_PIN, Y_DIR_PIN, Y_ENABLE_PIN, Y_MIN_PIN, Y_MAX_PIN, Z_STEP_PIN, Z_DIR_PIN, Z_ENABLE_PIN, Z_MIN_PIN, Z_MAX_PIN, PS_ON_PIN, \
                         HEATER_BED_PIN, ORIG_FAN_PIN,                  \
                         _E0_PINS _E1_PINS _E2_PINS _E3_PINS           \
-                        analogInputToDigitalPin(ORIG_TEMP_0_PIN), analogInputToDigitalPin(ORIG_TEMP_1_PIN), analogInputToDigitalPin(ORIG_TEMP_2_PIN), analogInputToDigitalPin(ORIG_TEMP_3_PIN), analogInputToDigitalPin(ORIG_TEMP_BED_PIN) }
+                        analogInputToDigitalPin(TEMP_0_PIN), analogInputToDigitalPin(TEMP_1_PIN), analogInputToDigitalPin(TEMP_2_PIN), analogInputToDigitalPin(TEMP_3_PIN), analogInputToDigitalPin(TEMP_BED_PIN) }
 #endif

MarlinKimbra/pins2tool.h

+//============================================================================
+//==================== Change PIN width Configurator Tool ====================
+//============================================================================
+
+
+//============================================================================
\ No newline at end of file