Skip to content

M
MarlinKimbra
Commit cbdc92ce authored by MagoKimbra's avatar MagoKimbra
Browse files
Options

Merge remote-tracking branch 'refs/remotes/origin/master' into dev

parents 39c74afd 30264bfb
Show whitespace changes
Inline Side-by-side
Showing with 54 additions and 39 deletions
MarlinKimbra/Configuration_Delta.h
View file @ cbdc92ce
......@@ -127,7 +127,7 @@
// How much the nozzle will be raised when travelling from between next probing points
#define Z_RAISE_BETWEEN_PROBINGS 5
// Works best with ACCURATE_BED_LEVELING_POINTS 5 or higher.
// Define the grid for bed level AUTO BED LEVELING GRID POINTS X AUTO BED LEVELING GRID POINTS.
#define AUTO_BED_LEVELING_GRID_POINTS 9
/*****************************************************************************************/
......
MarlinKimbra/Configuration_Feature.h
View file @ cbdc92ce
......@@ -59,8 +59,9 @@
* - Laser beam
* ADVANCED MOTION FEATURES:
* - Stepper auto deactivation
* - Microstepping
* - Low speed stepper
* - High speed stepper
* - Microstepping
* - Motor's current
* - I2C DIGIPOT
* - Toshiba steppers
......@@ -1266,31 +1267,43 @@
/***********************************************************************
*************************** Microstepping *****************************
************************* Low speed stepper ***************************
***********************************************************************
* *
* Microstep setting (Only functional when stepper driver *
* microstep pins are connected to MCU. *
* Use it if you have low speed stepper driver *
* *
* Alligator Board support 16 or 32 only value *
* Uncomment STEPPER_HIGH_LOW to enable this feature *
* *
***********************************************************************/
//#define USE_MICROSTEPS
#define MICROSTEP_MODES {16, 16, 16, 16} // X Y Z E - [1,2,4,8,16,32]
//#define STEPPER_HIGH_LOW
#define STEPPER_HIGH_LOW_DELAY 1u // Delay in microseconds
/***********************************************************************/
/***********************************************************************
************************* Low speed stepper ***************************
************************* High speed stepper **************************
***********************************************************************
* *
* Use it if you have low speed stepper driver *
* Activate for very high stepping rates, normally only needed for 1/64*
* or more micro steps (AXIS_STEPS_PER_UNIT * MAX_FEEDRATE > 150,000) *
* *
* Uncomment STEPPER_HIGH_LOW to enable this feature *
***********************************************************************/
//#define ENABLE_HIGH_SPEED_STEPPING
/***********************************************************************/
/***********************************************************************
*************************** Microstepping *****************************
***********************************************************************
* *
* Microstep setting (Only functional when stepper driver *
* microstep pins are connected to MCU. *
* *
* Alligator Board support 16 or 32 only value *
* *
***********************************************************************/
//#define STEPPER_HIGH_LOW
#define STEPPER_HIGH_LOW_DELAY 1u // Delay in microseconds
//#define USE_MICROSTEPS
#define MICROSTEP_MODES {16, 16, 16, 16} // X Y Z E - [1,2,4,8,16,32]
/***********************************************************************/
......
MarlinKimbra/Marlin_main.cpp
View file @ cbdc92ce
......@@ -188,7 +188,7 @@
* M218 - Set hotend offset (in mm): T<extruder_number> X<offset_on_X> Y<offset_on_Y>
* M220 - Set speed factor override percentage: S<factor in percent>
* M221 - Set extrude factor override percentage: S<factor in percent>
* M222 - Set density extrusion percentage: S<factor in percent>
* M222 - Set density extrusion percentage for purge: S<factor in percent>
* M226 - Wait until the specified pin reaches the state required: P<pin number> S<pin state>
* M240 - Trigger a camera to take a photograph
* M250 - Set LCD contrast C<contrast value> (value 0..63)
......@@ -2514,7 +2514,7 @@ static void clean_up_after_endstop_move() {
double xProbe = left_probe_bed_position + xGridSpacing * xCount;
// Avoid probing the corners (outside the round or hexagon print surface) on a delta printer.
float distance_from_center = sqrt(xProbe*xProbe + yProbe*yProbe);
float distance_from_center = sqrt(xProbe * xProbe + yProbe * yProbe);
if (distance_from_center > DELTA_PROBABLE_RADIUS) continue;
bed_level[xCount][yCount] = probe_bed(xProbe, yProbe);
......@@ -7442,11 +7442,11 @@ void process_next_command() {
gcode_M218(); break;
#endif
case 220: // M220 S<factor in percent>- set speed factor override percentage
case 220: // M220 S<factor in percent> - set speed factor override percentage
gcode_M220(); break;
case 221: // M221 T<extruder> S<factor in percent>- set extrude factor override percentage
case 221: // M221 T<extruder> S<factor in percent> - set extrude factor override percentage
gcode_M221(); break;
case 222: // M222 T<extruder> S<factor in percent>- set Density extrude factor override percentage
case 222: // M222 T<extruder> S<factor in percent> - set density extrude factor percentage for purge
gcode_M222(); break;
case 226: // M226 P<pin number> S<pin state>- Wait until the specified pin reaches the state required
gcode_M226(); break;
......
MarlinKimbra/Pins.h
View file @ cbdc92ce
......@@ -5369,12 +5369,8 @@ DaveX plan for Teensylu/printrboard-type pinouts (ref teensylu & sprinter) for a
#define MOSI_PIN 75
#define MISO_PIN 74
#define SCK_PIN 76
#define SS_PIN 77
#else
#define DUE_SOFTWARE_SPI
#define MOSI_PIN 51
#define MISO_PIN 50
#define SCK_PIN 52
#endif
/****************************************************************************************/
......
MarlinKimbra/module/cardreader.cpp
View file @ cbdc92ce
......@@ -294,11 +294,13 @@ void CardReader::openFile(char* name, bool read, bool replace_current/*=true*/,
ECHO_EMV("\" pos", sdpos);
filespos[file_subcall_ctr] = sdpos;
file_subcall_ctr++;
} else {
}
else {
ECHO_LMV(DB, "Now doing file: ", name);
}
file.close();
} else { // opening fresh file
}
else { // opening fresh file
file_subcall_ctr = 0; // resetting procedure depth in case user cancels print while in procedure
ECHO_LMV(DB, "Now fresh file: ", name);
}
......@@ -320,12 +322,14 @@ void CardReader::openFile(char* name, bool read, bool replace_current/*=true*/,
ECHO_SMV(ER, SERIAL_SD_OPEN_FILE_FAIL, subdirname);
ECHO_EM(".");
return;
} else {
}
else {
//ECHO_EM("dive ok");
}
curDir = &myDir;
dirname_start = dirname_end + 1;
} else { // the remainder after all /fsa/fdsa/ is the filename
}
else { // the remainder after all /fsa/fdsa/ is the filename
fname = dirname_start;
//ECHO_EM("remainder");
//ECHO_EV(fname);
......
MarlinKimbra/module/cardreader.h
View file @ cbdc92ce
......@@ -9,7 +9,7 @@
enum LsAction { LS_SerialPrint, LS_Count, LS_GetFilename };
class CardReader {
public:
public:
CardReader();
void initsd();
......@@ -30,9 +30,9 @@ class CardReader {
void getStatus();
void printingHasFinished();
#if ENABLED(LONG_FILENAME_HOST_SUPPORT)
#if ENABLED(LONG_FILENAME_HOST_SUPPORT)
void printLongPath(char* path);
#endif
#endif
void getfilename(uint16_t nr, const char* const match = NULL);
uint16_t getnrfilenames();
......@@ -53,18 +53,18 @@ class CardReader {
FORCE_INLINE uint8_t percentDone() { return (isFileOpen() && filesize) ? sdpos / ((filesize + 99) / 100) : 0; }
FORCE_INLINE char* getWorkDirName() { workDir.getFilename(filename); return filename; }
public:
public:
bool saving, logging, sdprinting, cardOK, filenameIsDir;
char filename[FILENAME_LENGTH], longFilename[LONG_FILENAME_LENGTH];
int autostart_index;
private:
private:
SdFile root, *curDir, workDir, lastDir, workDirParents[MAX_DIR_DEPTH];
uint16_t workDirDepth;
Sd2Card card;
SdVolume volume;
SdFile file;
#define SD_PROCEDURE_DEPTH 1
#define MAXPATHNAMELENGTH (FILENAME_LENGTH*MAX_DIR_DEPTH + MAX_DIR_DEPTH + 1)
#define SD_PROCEDURE_DEPTH 1
#define MAXPATHNAMELENGTH (FILENAME_LENGTH * MAX_DIR_DEPTH + MAX_DIR_DEPTH + 1)
uint8_t file_subcall_ctr;
uint32_t filespos[SD_PROCEDURE_DEPTH];
char filenames[SD_PROCEDURE_DEPTH][MAXPATHNAMELENGTH];
......
MarlinKimbra/module/comunication.h
View file @ cbdc92ce
......@@ -26,7 +26,9 @@
#endif // BLUETOOTH
#else
#ifdef __SAM3X8E__
#if SERIAL_PORT == 0
#if SERIAL_PORT == -1
#define MYSERIAL SerialUSB
#elif SERIAL_PORT == 0
#define MYSERIAL Serial
#elif SERIAL_PORT == 1
#define MYSERIAL Serial1
......
MarlinKimbra/module/conditionals.h
View file @ cbdc92ce
......@@ -337,14 +337,14 @@
#define HOMING_BUMP_DIVISOR {XYZ_BUMP_DIVISOR, XYZ_BUMP_DIVISOR, XYZ_BUMP_DIVISOR}
// Effective horizontal distance bridged by diagonal push rods.
#define DEFAULT_DELTA_RADIUS (DELTA_SMOOTH_ROD_OFFSET-DELTA_EFFECTOR_OFFSET-DELTA_CARRIAGE_OFFSET)
#define DEFAULT_DELTA_RADIUS (DELTA_SMOOTH_ROD_OFFSET - DELTA_EFFECTOR_OFFSET - DELTA_CARRIAGE_OFFSET)
#define LEFT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
#define RIGHT_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
#define FRONT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
#define BACK_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
// Radius for probe
#define DELTA_PROBABLE_RADIUS BED_PRINTER_RADIUS
#define DELTA_PROBABLE_RADIUS BED_PRINTER_RADIUS - 5
#endif
/**
......
MarlinKimbra/module/sanitycheck.h
View file @ cbdc92ce
......@@ -1681,7 +1681,7 @@
#error DEPENDENCY ERROR: You have to set E0E1_CHOICE_PIN, E0E2_CHOICE_PIN and E0E3_CHOICE_PIN to a valid pin if you enable MKR4 with 4 extruder and 1 driver
#elif (EXTRUDERS == 3) && (DRIVER_EXTRUDERS == 2) && !PIN_EXISTS(E0E2_CHOICE)
#error DEPENDENCY ERROR: You have to set E0E2_CHOICE_PIN to a valid pin if you enable MKR4 with 3 extruder and 2 driver
#elif (EXTRUDERS == 4) && (DRIVER_EXTRUDERS == 2) && (!PIN_EXISTS(E0E1_CHOICE) || !PIN_EXISTS(E1E3_CHOICE))
#elif (EXTRUDERS == 4) && (DRIVER_EXTRUDERS == 2) && (!PIN_EXISTS(E0E2_CHOICE) || !PIN_EXISTS(E1E3_CHOICE))
#error DEPENDENCY ERROR: You have to set E0E2_CHOICE_PIN and E1E3_CHOICE_PIN to a valid pin if you enable MKR4 with 4 extruder and 2 driver
#endif
#endif
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment