Skip to content

M
MarlinKimbra
Commit a31c8515 authored by Franco (nextime) Lanza's avatar Franco (nextime) Lanza
Browse files
Options

Fix Configuration_Basic

parent 0b6d01a6
Pipeline #111 skipped
Show whitespace changes
Inline Side-by-side
Showing with 7 additions and 140 deletions
MK/Configuration_Basic.h
View file @ a31c8515
...@@ -7,10 +7,9 @@ ...@@ -7,10 +7,9 @@
* - Board type * - Board type
* - Mechanism type * - Mechanism type
* - Extruders number * - Extruders number
* - Thermistor type
* - Temperature limits
* *
* Mechanisms-settings can be found in Configuration_Xxxxxx.h (where Xxxxxx can be: Cartesian - Delta - Core - Scara) * Mechanisms-settings can be found in Configuration_Xxxxxx.h (where Xxxxxx can be: Cartesian - Delta - Core - Scara)
* Temperature settings can be found in Configuration_Temperature.h
* Feature-settings can be found in Configuration_Feature.h * Feature-settings can be found in Configuration_Feature.h
* Pins-settings can be found in "Configuration_Pins.h" * Pins-settings can be found in "Configuration_Pins.h"
*/ */
...@@ -55,10 +54,13 @@ ...@@ -55,10 +54,13 @@
// Uncomment to include more info in ok command // Uncomment to include more info in ok command
//#define ADVANCED_OK //#define ADVANCED_OK
// By default MarlinKimbra will send a busy status message to the host //
// Host Keepalive
//
// When enabled MarlinKimbra will send a busy status message to the host
// every couple of seconds when it can't accept commands. // every couple of seconds when it can't accept commands.
// Enable this option if your host doesn't like keepalive messages. #define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages
//#define DISABLE_HOST_KEEPALIVE #define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113.
/***********************************************************************/ /***********************************************************************/
...@@ -113,16 +115,6 @@ ...@@ -113,16 +115,6 @@
//#define PS_DEFAULT_OFF //#define PS_DEFAULT_OFF
/*************************************************************************************/ /*************************************************************************************/
/***********************************************************************
******************************* Cooler ********************************
***********************************************************************
* *
* Uncomment the following line to enable COOLER support *
* *
***********************************************************************/
//#define COOLER
/*********************************************************************** /***********************************************************************
************************** Extruders number *************************** ************************** Extruders number ***************************
...@@ -134,129 +126,4 @@ ...@@ -134,129 +126,4 @@
#define DRIVER_EXTRUDERS 1 #define DRIVER_EXTRUDERS 1
/***********************************************************************/ /***********************************************************************/
/*****************************************************************************************************
************************************** Thermistor type **********************************************
*****************************************************************************************************
* *
* 4.7kohm PULLUP! *
* This is a normal value, if you use a 1k pullup thermistor see below *
* Please choose the one that matches your setup and set to TEMP_SENSOR_. *
* *
* Temperature sensor settings (4.7kohm PULLUP): *
* -2 is thermocouple with MAX6675 (only for sensor 0) *
* -1 is thermocouple with AD595 or AD597 *
* 0 is not used *
* 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup) *
* 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) *
* 3 is Mendel-parts thermistor (4.7k pullup) *
* 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! *
* 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup) *
* 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) *
* 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) *
* 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) *
* 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) *
* 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup) *
* 10 is 100k RS thermistor 198-961 (4.7k pullup) *
* 11 is 100k beta 3950 1% thermistor (4.7k pullup) *
* 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed) *
* 13 is 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" *
* 20 is the PT100 circuit found in the Ultimainboard V2.x *
* 40 is the 10k Carel NTC015WH01 or ELIWELL SN8T6A1502 (4.7k pullup) *
* 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950 *
* *
* 1kohm PULLUP! *
* This is not normal, you would have to have changed out your 4.7k for 1k *
* (but gives greater accuracy and more stable PID) *
* Please choose the one that matches your setup. *
* *
* Temperature sensor settings (1kohm PULLUP): *
* 51 is 100k thermistor - EPCOS (1k pullup) *
* 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup) *
* 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup) *
* *
* 1047 is Pt1000 with 4k7 pullup *
* 1010 is Pt1000 with 1k pullup (non standard) *
* 147 is Pt100 with 4k7 pullup *
* 110 is Pt100 with 1k pullup (non standard) *
* 998 and 999 are Dummy Tables. ALWAYS read 25°C or DUMMY_THERMISTOR_998_VALUE temperature *
* *
*****************************************************************************************************/
#define TEMP_SENSOR_0 0
#define TEMP_SENSOR_1 0
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_COOLER 0
//These 2 defines help to calibrate the AD595 sensor in case you get wrong temperature measurements.
//The measured temperature is defined as "actualTemp = (measuredTemp * TEMP_SENSOR_AD595_GAIN) + TEMP_SENSOR_AD595_OFFSET"
#define TEMP_SENSOR_AD595_OFFSET 0.0
#define TEMP_SENSOR_AD595_GAIN 1.0
// Use it for Testing or Development purposes. NEVER for production machine.
#define DUMMY_THERMISTOR_998_VALUE 25
#define DUMMY_THERMISTOR_999_VALUE 25
//Show Temperature ADC value
//The M105 command return, besides traditional information, the ADC value read from temperature sensors.
//#define SHOW_TEMP_ADC_VALUES
/*****************************************************************************************************/
/***********************************************************************
************************* Temperature limits ***************************
***********************************************************************/
// Hotend temperature must be close to target for this long before M109 returns success
#define TEMP_RESIDENCY_TIME 10 // (seconds)
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success
#define TEMP_BED_RESIDENCY_TIME 0 // (seconds)
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Cooler temperature must be close to target for this long before M190 returns success
#define TEMP_COOLER_RESIDENCY_TIME 0 // (seconds)
#define TEMP_COOLER_HYSTERESIS 1 // (degC) range of +/- temperatures considered "close" to the target one
#define TEMP_COOLER_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// When temperature exceeds max temp, your heater will be switched off.
// When temperature exceeds max temp, your cooler cannot be activaed.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
// You should use MINTEMP for thermistor short/failure protection.
#define HEATER_0_MAXTEMP 275 // (degC)
#define HEATER_1_MAXTEMP 275 // (degC)
#define HEATER_2_MAXTEMP 275 // (degC)
#define HEATER_3_MAXTEMP 275 // (degC)
#define BED_MAXTEMP 150 // (degC)
#define COOLER_MAXTEMP 35 //
// The minimal temperature defines the temperature below which the heater will not be enabled It is used
// or, in case of cooler, it will switched off.
// to check that the wiring to the thermistor is not broken.
// Otherwise this would lead to the heater being powered on all the time.
#define HEATER_0_MINTEMP 5 // (degC)
#define HEATER_1_MINTEMP 5 // (degC)
#define HEATER_2_MINTEMP 5 // (degC)
#define HEATER_3_MINTEMP 5 // (degC)
#define BED_MINTEMP 5 // (degC)
#define COOLER_MINTEMP 10 // (degC)
//Preheat Constants
#define PLA_PREHEAT_HOTEND_TEMP 190
#define PLA_PREHEAT_HPB_TEMP 60
#define PLA_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
#define ABS_PREHEAT_HOTEND_TEMP 240
#define ABS_PREHEAT_HPB_TEMP 100
#define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
#define GUM_PREHEAT_HOTEND_TEMP 230
#define GUM_PREHEAT_HPB_TEMP 60
#define GUM_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
/*****************************************************************************************************/
#endif #endif
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment