* G10 - retract filament according to settings of M207
* G11 - retract recover filament according to settings of M208
* G28 - X0 Y0 Z0 Home all Axis. G28 M for bed manual setting with LCD.
* G29 - Detailed Z-Probe, probes the bed at 4 points. You must de at the home position for this to work correctly.
G29 Fyyy Lxxx Rxxx Byyy for probe in this 4 points.
* G29 - Detailed Z-Probe, probes the bed at 3 points or grid. You must be at the home position for this to work correctly.
G29 Fyyy Lxxx Rxxx Byyy for customer grid.
* G30 - Single Z Probe, probes bed at current XY location.
Bed Probe and Delta geometry Autocalibration G30 A
* G31 - Dock Z Probe sled (if enabled)
...
...
@@ -76,31 +76,33 @@
* M203 - Set maximum feedrate that your machine can sustain (M203 X200 Y200 Z300 E10000) in mm/sec
* M204 - Set default acceleration: S normal moves T filament only moves (M204 S3000 T7000) im mm/sec^2 also sets minimum segment time in ms (B20000) to prevent buffer underruns and M20 minimum feedrate
* M205 - advanced settings: minimum travel speed S=while printing T=travel only, B=minimum segment time X= maximum xy jerk, Z=maximum Z jerk, E=maximum E jerk
* M206 - set additional homeing offset
* M206 - set additional homing offset
* M207 - set retract length S[positive mm] F[feedrate mm/min] Z[additional zlift/hop], stays in mm regardless of M200 setting
* M208 - set recover=unretract length S[positive mm surplus to the M207 S*] F[feedrate mm/min]
* M209 - S1=true/0=false enable automatic retract detect if the slicer did not support G10/11: every normal extrude-only move will be classified as retract depending on the direction.
* M209 - S[1=true/0=false] enable automatic retract detect if the slicer did not support G10/11: every normal extrude-only move will be classified as retract depending on the direction.
* M218 - set hotend offset (in mm): Textruder_number Xoffset_on_X Yoffset_on_Y
* M220 Sfactor in percent- set speed factor override percentage
* M221 Sfactor in percent- set extrude factor override percentage
* M220 - S[factor in percent]- set speed factor override percentage
* M221 - S[factor in percent]- set extrude factor override percentage
* M240 - Trigger a camera to take a photograph
* M280 - Position an RC Servo Pindex Sangle/microseconds, ommit S to report back current angle
* M300 - Play beepsound Sfrequency Hz Pduration ms
* M300 - Play beep sound S[frequency] Hz P[duration] ms
* M301 - Set PID parameters P I and D
* M302 - Allow cold extrudes
* M303 - PID relay autotune Stemperature sets the target temperature. (default target temperature = 150C)
* M304 - Set bed PID parameters P I and D
* M350 - Set microstepping mode.
* M351 - Toggle MS1 MS2 pins directly.
* M400 - Finish all moves
* M401 - Lower z-probe if present
* M402 - Raise z-probe if present
* M404 - Ndia in mm Enter the nominal filament width (3mm, 1.75mm ) or will display nominal filament width without parameters
* M405 - Turn on Filament Sensor extrusion control. Optional Ddelay in cm to set delay in centimeters between sensor and extruder
* M404 - N[dia in mm] Enter the nominal filament width (3mm, 1.75mm ) or will display nominal filament width without parameters
* M405 - Turn on Filament Sensor extrusion control. Optional D[delay in cm] to set delay in centimeters between sensor and extruder
* M406 - Turn off Filament Sensor extrusion control
* M407 - Displays measured filament diameter
* M500 - stores paramters in EEPROM
* M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
* M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
* M503 - print the current settings (from memory not from eeprom)
* M503 - print the current settings (from memory not from EEPROM)
* M540 - Use S[0|1] to enable or disable the stop SD card print on endstop hit (requires ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED)
* M600 - Pause for filament change X[pos] Y[pos] Z[relative lift] E[initial retract] L[later retract distance for removal]
* M605 - Set dual x-carriage movement mode: Smode [ X<duplication x-offset> Rduplication temp offset ]
