Fix pins.h

MarlinKimbra/Configuration_Basic.h

@@ -150,7 +150,7 @@
 #define TEMP_SENSOR_1 0
 #define TEMP_SENSOR_2 0
 #define TEMP_SENSOR_3 0
-#define TEMP_SENSOR_BED 1
+#define TEMP_SENSOR_BED 0
 
 //These 2 defines help to calibrate the AD595 sensor in case you get wrong temperature measurements.
 //The measured temperature is defined as "actualTemp = (measuredTemp * TEMP_SENSOR_AD595_GAIN) + TEMP_SENSOR_AD595_OFFSET"

MarlinKimbra/pins.h

@@ -2324,29 +2324,32 @@
 
 #define ORIG_X_STEP_PIN     54
 #define ORIG_X_DIR_PIN      55
-#define ORIG_X_MIN_PIN      3
-#define ORIG_X_MAX_PIN      2
 #define ORIG_X_ENABLE_PIN   38
+#define X_MIN_PIN           3
+#define X_MAX_PIN           2
+
 
 #define ORIG_Y_STEP_PIN     60  
 #define ORIG_Y_DIR_PIN      61
-#define ORIG_Y_MIN_PIN      14
-#define ORIG_Y_MAX_PIN      15
 #define ORIG_Y_ENABLE_PIN   56
+#define Y_MIN_PIN           14
+#define Y_MAX_PIN           15
+
 
 #define ORIG_Z_STEP_PIN     46
 #define ORIG_Z_DIR_PIN      48
-#define ORIG_Z_MIN_PIN      18
-#define ORIG_Z_MAX_PIN      19
 #define ORIG_Z_ENABLE_PIN   62
+#define Z_MIN_PIN           18
+#define Z_MAX_PIN           19
+
 
 // Note that on the Due pin A0 on the board is channel 2 on the ARM chip
 #define ORIG_HEATER_0_PIN   10
 #define ORIG_TEMP_0_PIN     11  // Due analog pin #
-#define ORIG_HEATER_1_PIN   8
-#define ORIG_TEMP_1_PIN     12  // Due analog pin #
-#define ORIG_HEATER_BED_PIN 9
-#define ORIG_TEMP_BED_PIN   13  // Due analog pin #
+#define ORIG_HEATER_BED_PIN 8
+#define ORIG_TEMP_BED_PIN   12  // Due analog pin #
+#define ORIG_HEATER_1_PIN   9
+#define ORIG_TEMP_1_PIN     13  // Due analog pin #
 
 #define ORIG_E0_STEP_PIN    26
 #define ORIG_E0_DIR_PIN     28
@@ -2357,7 +2360,7 @@
 #define ORIG_E1_ENABLE_PIN  30
 
 #define SDPOWER             -1
-#define SDSS                53  // 10 if using HW SPI. 53 if using SW SPI
+#define SDSS                10  // 10 if using HW SPI. 53 if using SW SPI
 #define LED_PIN             13
 #define ORIG_FAN_PIN        9
 #define PS_ON_PIN           12
@@ -2397,16 +2400,11 @@
 #define ORIG_Z_ENABLE_PIN       62
 #define Z_MIN_PIN               18
 #define Z_MAX_PIN               19
-#define Z_PROBE_PIN        -1
 
 #define Y2_STEP_PIN             36
 #define Y2_DIR_PIN              34
 #define Y2_ENABLE_PIN           30
 
-#undef Z2_STEP_PIN
-#undef Z2_DIR_PIN
-#undef Z2_ENABLE_PIN
-
 #define Z2_STEP_PIN             36
 #define Z2_DIR_PIN              34
 #define Z2_ENABLE_PIN           30