Skip to content

M
MarlinKimbra
Commit 62a98bb6 authored by MagoKimbra's avatar MagoKimbra
Browse files
Options

Same fix

parent f004c9cd
Show whitespace changes
Inline Side-by-side
Showing with 105 additions and 116 deletions
MarlinKimbra/Configuration_Feature.h
View file @ 62a98bb6
......@@ -549,6 +549,7 @@
* *
*****************************************************************************************/
//#define ADVANCE
#define EXTRUDER_ADVANCE_K .0
#define D_FILAMENT 2.85
#define STEPS_MM_E 836
......@@ -566,6 +567,7 @@
* *
**************************************************************************/
//#define FILAMENTCHANGEENABLE
#define FILAMENTCHANGE_XPOS 3
#define FILAMENTCHANGE_YPOS 3
#define FILAMENTCHANGE_ZADD 10
......@@ -726,6 +728,7 @@
* *
**************************************************************************/
//#define FWRETRACT //ONLY PARTIALLY TESTED
#define MIN_RETRACT 0.1 //minimum extruded mm to accept a automatic gcode retraction attempt
#define RETRACT_LENGTH 3 //default retract length (positive mm)
#define RETRACT_LENGTH_SWAP 13 //default swap retract length (positive mm), for extruder change
......@@ -879,6 +882,7 @@
* *
**********************************************************************************/
//#define FILAMENT_SENSOR
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2,3)
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel
#define MEASURED_UPPER_LIMIT 2.00 //upper limit factor used for sensor reading validation in mm
......@@ -908,6 +912,7 @@
* *
**********************************************************************************/
//#define FILAMENT_RUNOUT_SENSOR
#define FILRUNOUT_PIN_INVERTING true // Should be uncommented and true or false should assigned
#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
#define FILAMENT_RUNOUT_SCRIPT "M600" // Script execute when filament run out
......@@ -963,6 +968,7 @@
* *
**************************************************************************/
//#define POWER_CONSUMPTION
#define POWER_VOLTAGE 12.00 //(V) The power supply OUT voltage
#define POWER_SENSITIVITY 0.066 //(V/A) How much increase V for 1A of increase
#define POWER_OFFSET 0.005 //(A) Help to get 0A when no load is connected.
......@@ -1209,6 +1215,7 @@
* *
**************************************************************************/
//#define CHDK
#define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again
/**************************************************************************/
......@@ -1333,54 +1340,54 @@
//#define HAVE_TMCDRIVER
//#define X_IS_TMC
//#define X_MAX_CURRENT 1000 //in mA
//#define X_SENSE_RESISTOR 91 //in mOhms
//#define X_MICROSTEPS 16 //number of microsteps
#define X_MAX_CURRENT 1000 //in mA
#define X_SENSE_RESISTOR 91 //in mOhms
#define X_MICROSTEPS 16 //number of microsteps
//#define X2_IS_TMC
//#define X2_MAX_CURRENT 1000 //in mA
//#define X2_SENSE_RESISTOR 91 //in mOhms
//#define X2_MICROSTEPS 16 //number of microsteps
#define X2_MAX_CURRENT 1000 //in mA
#define X2_SENSE_RESISTOR 91 //in mOhms
#define X2_MICROSTEPS 16 //number of microsteps
//#define Y_IS_TMC
//#define Y_MAX_CURRENT 1000 //in mA
//#define Y_SENSE_RESISTOR 91 //in mOhms
//#define Y_MICROSTEPS 16 //number of microsteps
#define Y_MAX_CURRENT 1000 //in mA
#define Y_SENSE_RESISTOR 91 //in mOhms
#define Y_MICROSTEPS 16 //number of microsteps
//#define Y2_IS_TMC
//#define Y2_MAX_CURRENT 1000 //in mA
//#define Y2_SENSE_RESISTOR 91 //in mOhms
//#define Y2_MICROSTEPS 16 //number of microsteps
#define Y2_MAX_CURRENT 1000 //in mA
#define Y2_SENSE_RESISTOR 91 //in mOhms
#define Y2_MICROSTEPS 16 //number of microsteps
//#define Z_IS_TMC
//#define Z_MAX_CURRENT 1000 //in mA
//#define Z_SENSE_RESISTOR 91 //in mOhms
//#define Z_MICROSTEPS 16 //number of microsteps
#define Z_MAX_CURRENT 1000 //in mA
#define Z_SENSE_RESISTOR 91 //in mOhms
#define Z_MICROSTEPS 16 //number of microsteps
//#define Z2_IS_TMC
//#define Z2_MAX_CURRENT 1000 //in mA
//#define Z2_SENSE_RESISTOR 91 //in mOhms
//#define Z2_MICROSTEPS 16 //number of microsteps
#define Z2_MAX_CURRENT 1000 //in mA
#define Z2_SENSE_RESISTOR 91 //in mOhms
#define Z2_MICROSTEPS 16 //number of microsteps
//#define E0_IS_TMC
//#define E0_MAX_CURRENT 1000 //in mA
//#define E0_SENSE_RESISTOR 91 //in mOhms
//#define E0_MICROSTEPS 16 //number of microsteps
#define E0_MAX_CURRENT 1000 //in mA
#define E0_SENSE_RESISTOR 91 //in mOhms
#define E0_MICROSTEPS 16 //number of microsteps
//#define E1_IS_TMC
//#define E1_MAX_CURRENT 1000 //in mA
//#define E1_SENSE_RESISTOR 91 //in mOhms
//#define E1_MICROSTEPS 16 //number of microsteps
#define E1_MAX_CURRENT 1000 //in mA
#define E1_SENSE_RESISTOR 91 //in mOhms
#define E1_MICROSTEPS 16 //number of microsteps
//#define E2_IS_TMC
//#define E2_MAX_CURRENT 1000 //in mA
//#define E2_SENSE_RESISTOR 91 //in mOhms
//#define E2_MICROSTEPS 16 //number of microsteps
#define E2_MAX_CURRENT 1000 //in mA
#define E2_SENSE_RESISTOR 91 //in mOhms
#define E2_MICROSTEPS 16 //number of microsteps
//#define E3_IS_TMC
//#define E3_MAX_CURRENT 1000 //in mA
//#define E3_SENSE_RESISTOR 91 //in mOhms
//#define E3_MICROSTEPS 16 //number of microsteps
#define E3_MAX_CURRENT 1000 //in mA
#define E3_SENSE_RESISTOR 91 //in mOhms
#define E3_MICROSTEPS 16 //number of microsteps
/***********************************************************************/
......@@ -1397,64 +1404,64 @@
//#define HAVE_L6470DRIVER
//#define X_IS_L6470
//#define X_MICROSTEPS 16 //number of microsteps
//#define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
//#define X_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
//#define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall
#define X_MICROSTEPS 16 //number of microsteps
#define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
#define X_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
#define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall
//#define X2_IS_L6470
//#define X2_MICROSTEPS 16 //number of microsteps
//#define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
//#define X2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
//#define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
#define X2_MICROSTEPS 16 //number of microsteps
#define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
#define X2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
#define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
//#define Y_IS_L6470
//#define Y_MICROSTEPS 16 //number of microsteps
//#define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
//#define Y_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
//#define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall
#define Y_MICROSTEPS 16 //number of microsteps
#define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
#define Y_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
#define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall
//#define Y2_IS_L6470
//#define Y2_MICROSTEPS 16 //number of microsteps
//#define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
//#define Y2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
//#define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
#define Y2_MICROSTEPS 16 //number of microsteps
#define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
#define Y2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
#define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
//#define Z_IS_L6470
//#define Z_MICROSTEPS 16 //number of microsteps
//#define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
//#define Z_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
//#define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall
#define Z_MICROSTEPS 16 //number of microsteps
#define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
#define Z_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
#define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall
//#define Z2_IS_L6470
//#define Z2_MICROSTEPS 16 //number of microsteps
//#define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
//#define Z2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
//#define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
#define Z2_MICROSTEPS 16 //number of microsteps
#define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
#define Z2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
#define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
//#define E0_IS_L6470
//#define E0_MICROSTEPS 16 //number of microsteps
//#define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
//#define E0_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
//#define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall
#define E0_MICROSTEPS 16 //number of microsteps
#define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
#define E0_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
#define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall
//#define E1_IS_L6470
//#define E1_MICROSTEPS 16 //number of microsteps
//#define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
//#define E1_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
//#define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall
#define E1_MICROSTEPS 16 //number of microsteps
#define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
#define E1_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
#define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall
//#define E2_IS_L6470
//#define E2_MICROSTEPS 16 //number of microsteps
//#define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
//#define E2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
//#define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
#define E2_MICROSTEPS 16 //number of microsteps
#define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
#define E2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
#define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
//#define E3_IS_L6470
//#define E3_MICROSTEPS 16 //number of microsteps
//#define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
//#define E3_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
//#define E3_STALLCURRENT 1500 //current in mA where the driver will detect a stall
#define E3_MICROSTEPS 16 //number of microsteps
#define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
#define E3_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
#define E3_STALLCURRENT 1500 //current in mA where the driver will detect a stall
/**********************************************************************************/
......
MarlinKimbra/module/nextion_gfx.h
View file @ 62a98bb6
......@@ -15,6 +15,7 @@
*
*/
#ifndef NEXTION_GFX_H
#define NEXTION_GFX_H
......
MarlinKimbra/module/nextion_lcd.cpp
View file @ 62a98bb6
......@@ -17,10 +17,8 @@
#include "nextion_gfx.h"
#include <Nextion.h>
const float MaxWave = 0.2;
bool NextionON = false;
bool PageInfo = false;
bool gfxON = false;
char buffer[100] = {0};
uint32_t slidermaxval = 20;
char lcd_status_message[30] = WELCOME_MSG;
......@@ -28,7 +26,7 @@
static millis_t next_lcd_update_ms;
#if ENABLED(NEXTION_GFX)
GFX gfx = GFX(196, 194);
GFX gfx = GFX(200, 190);
#endif
// Page
......@@ -41,10 +39,10 @@
NexPage Pmove = NexPage(6, 0, "move");
// Text
NexText Hotend0 = NexText(1, 1, "t0");
NexText Hotend0 = NexText(1, 2, "t0");
NexText Hotend1 = NexText(1, 4, "t1");
NexText Hotend2 = NexText(1, 5, "t2");
NexText Hotend21 = NexText(1, 6, "h2");
NexText Hotend21 = NexText(1, 5, "h2");
NexText Hotend2 = NexText(1, 6, "t2");
NexText LedStatus = NexText(1, 7, "t4");
NexText LedCoord = NexText(1, 8, "t5");
NexText set0 = NexText(2, 2, "set0");
......@@ -57,15 +55,15 @@
NexText sdfolder = NexText(4, 23, "sdfolder");
// Picture
NexPicture Menu = NexPicture(1, 10, "p0");
NexPicture MSD = NexPicture(1, 11, "p1");
NexPicture MSetup = NexPicture(1, 12, "p2");
NexPicture Hend0 = NexPicture(1, 13, "p3");
NexPicture Menu = NexPicture(1, 9, "p0");
NexPicture MSD = NexPicture(1, 10, "p1");
NexPicture MSetup = NexPicture(1, 11, "p2");
NexPicture Hend0 = NexPicture(1, 12, "p3");
NexPicture Hend1 = NexPicture(1, 14, "p4");
NexPicture Hend2 = NexPicture(1, 15, "p5");
NexPicture Fanpic = NexPicture(1, 19, "p6");
NexPicture NPlay = NexPicture(1, 27, "p7");
NexPicture NStop = NexPicture(1, 28, "p8");
NexPicture Hend2 = NexPicture(1, 16, "p5");
NexPicture Fanpic = NexPicture(1, 18, "p6");
NexPicture NPlay = NexPicture(1, 24, "p7");
NexPicture NStop = NexPicture(1, 25, "p8");
NexPicture Exit1 = NexPicture(3, 4, "p3");
NexPicture Folder0 = NexPicture(4, 9, "p0");
NexPicture Folder1 = NexPicture(4, 10, "p1");
......@@ -86,32 +84,29 @@
NexPicture ZDown = NexPicture(6, 12, "p11");
// Progress Bar
NexProgressBar sdbar = NexProgressBar(1, 26, "j0");
NexProgressBar sdbar = NexProgressBar(1, 23, "j0");
// Slider
NexSlider sdlist = NexSlider(4, 1, "h0");
// Wafeform
NexWaveform Graph0 = NexWaveform(1, 9, "s0");
NexWaveform Graph1 = NexWaveform(1, 24, "s1");
NexWaveform Graph2 = NexWaveform(1, 25, "s2");
// Touch area
NexHotspot hot0 = NexHotspot(1, 14, "hot0");
NexHotspot hot1 = NexHotspot(1, 16, "hot1");
NexHotspot hot2 = NexHotspot(1, 18, "hot2");
NexHotspot hot0 = NexHotspot(1, 13, "hot0");
NexHotspot hot1 = NexHotspot(1, 15, "hot1");
NexHotspot hot2 = NexHotspot(1, 17, "hot2");
NexHotspot m11 = NexHotspot(2, 14, "m11");
NexHotspot tup = NexHotspot(2, 16, "tup");
NexHotspot tdown = NexHotspot(2, 17, "tdown");
// Timer
NexTimer startimer = NexTimer(0, 1, "tm0");
NexTimer fantimer = NexTimer(1, 23, "tm0");
NexTimer fantimer = NexTimer(1, 22, "tm0");
// Variable
NexVar Hotend = NexVar(1, 20, "he");
NexVar Hotend = NexVar(1, 19, "he");
NexVar Bed = NexVar(1, 20, "bed");
NexVar set1 = NexVar(2, 17, "set1");
NexVar Bed = NexVar(1, 21, "bed");
NexVar filename0 = NexVar(4, 19, "va0");
NexVar filename1 = NexVar(4, 20, "va1");
NexVar filename2 = NexVar(4, 21, "va2");
......@@ -165,14 +160,6 @@
NULL
};
NexWaveform *graph_list[] =
{
&Graph0,
&Graph1,
&Graph2,
NULL
};
NexText *row_list[] =
{
&sdrow0,
......@@ -211,6 +198,10 @@
PageInfo = true;
#if ENABLED(NEXTION_GFX)
gfx_clear(X_MAX_POS, Y_MAX_POS, Z_MAX_POS);
#endif
#if HAS_TEMP_0
Hotend.setValue(1);
#endif
......@@ -278,7 +269,6 @@
static void setpagesdcard() {
PageInfo = false;
gfxON = false;
Psdcard.show();
uint16_t fileCnt = card.getnrfilenames();
......@@ -436,12 +426,10 @@
void setpagePopCallback(void *ptr) {
if (ptr == &Menu) {
PageInfo = false;
gfxON = false;
Pmenu.show();
}
else if (ptr == &MSetup) {
PageInfo = false;
gfxON = false;
Psetup.show();
}
......@@ -561,11 +549,6 @@
hotend_list[h]->setText(buffer);
hotend_list[h]->setColor(color);
if (!gfxON) {
graph_list[h]->addValue(0, (int)(T1 * MaxWave));
graph_list[h]->addValue(1, (int)(T2 * MaxWave));
}
}
static void coordtoLCD() {
......@@ -678,19 +661,17 @@
#if ENABLED(NEXTION_GFX)
void gfx_clear(float x, float y, float z) {
if (PageInfo) {
if (PageInfo)
gfx.clear(x, y, z);
gfxON = true;
}
}
void gfx_cursor_to(float x, float y, float z) {
if (PageInfo && gfxON)
if (PageInfo)
gfx.cursor_to(x, y, z);
}
void gfx_line_to(float x, float y, float z){
if (PageInfo && gfxON)
if (PageInfo)
gfx.line_to(VC_TOOL, x, y, z);
}
#endif
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment