Skip to content

M
MarlinKimbra
Commit 521059bb authored by MagoKimbra's avatar MagoKimbra
Browse files
Options

Clear ALL

parent 0a201721
Expand all Show whitespace changes
Inline Side-by-side
Showing with 0 additions and 46031 deletions
MarlinKimbra/BlinkM.cpp deleted 100644 → 0
View file @ 0a201721
/*
BlinkM.cpp - Library for controlling a BlinkM over i2c
Created by Tim Koster, August 21 2013.
*/
#include "Marlin.h"
#ifdef BLINKM
#include "BlinkM.h"
void SendColors(byte red, byte grn, byte blu) {
Wire.begin();
Wire.beginTransmission(0x09);
Wire.write('o'); //to disable ongoing script, only needs to be used once
Wire.write('n');
Wire.write(red);
Wire.write(grn);
Wire.write(blu);
Wire.endTransmission();
}
#endif //BLINKM
MarlinKimbra/BlinkM.h deleted 100644 → 0
View file @ 0a201721
/*
BlinkM.h
Library header file for BlinkM library
*/
#if ARDUINO >= 100
#include "Arduino.h"
#else
#include "WProgram.h"
#endif
#include "Wire.h"
void SendColors(byte red, byte grn, byte blu);
MarlinKimbra/COPYING deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/Conditionals.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/Configuration.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/ConfigurationStore.cpp deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/ConfigurationStore.h deleted 100644 → 0
View file @ 0a201721
#ifndef __CONFIGURATIONSTORE_H
#define __CONFIGURATIONSTORE_H
#include "Configuration.h"
void Config_ResetDefault();
#ifndef DISABLE_M503
void Config_PrintSettings();
#else
FORCE_INLINE void Config_PrintSettings() {}
#endif
#ifdef EEPROM_SETTINGS
void Config_StoreSettings();
void Config_RetrieveSettings();
#else
FORCE_INLINE void Config_StoreSettings() {}
FORCE_INLINE void Config_RetrieveSettings() { Config_ResetDefault(); Config_PrintSettings(); }
#endif
#endif //__CONFIGURATIONSTORE_H
MarlinKimbra/Configuration_Cartesian.h deleted 100644 → 0
View file @ 0a201721
// Define this to set a custom name for your generic Mendel,
#define CUSTOM_MENDEL_NAME "Prusa"
//===========================================================================
//=============================Mechanical Settings===========================
//===========================================================================
// coarse Endstop Settings
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
#ifndef ENDSTOPPULLUPS
// fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined
// #define ENDSTOPPULLUP_XMAX
// #define ENDSTOPPULLUP_YMAX
// #define ENDSTOPPULLUP_ZMAX
// #define ENDSTOPPULLUP_XMIN
// #define ENDSTOPPULLUP_YMIN
// #define ENDSTOPPULLUP_ZMIN
// #define ENDSTOPPULLUP_EMIN
#endif
// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
const bool E_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
const bool X_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
const bool Y_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
// ENDSTOP SETTINGS:
// Sets direction of endstop when homing; 1=MAX, -1=MIN
#define X_HOME_DIR -1
#define Y_HOME_DIR -1
#define Z_HOME_DIR -1
#define E_HOME_DIR -1
#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
#define X_ENABLE_ON 0
#define Y_ENABLE_ON 0
#define Z_ENABLE_ON 0
#define E_ENABLE_ON 0 // For all extruder
// Disables axis when it's not being used.
#define DISABLE_X false
#define DISABLE_Y false
#define DISABLE_Z false
#define DISABLE_E false // For all extruder
#define DISABLE_INACTIVE_EXTRUDER false //disable only inactive extruder and keep active extruder enabled
// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
#define INVERT_X_DIR false
#define INVERT_Y_DIR false
#define INVERT_Z_DIR false
#define INVERT_E0_DIR false
#define INVERT_E1_DIR false
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
// Travel limits after homing (units are in mm)
#define X_MAX_POS 200
#define X_MIN_POS 0
#define Y_MAX_POS 200
#define Y_MIN_POS 0
#define Z_MAX_POS 200
#define Z_MIN_POS 0
#define E_MIN_POS 0
//=====================================================================================
//============================= Bed Manual or Auto Leveling ===========================
//=====================================================================================
// set the rectangle in which to probe in manual or automatic
#define LEFT_PROBE_BED_POSITION 20
#define RIGHT_PROBE_BED_POSITION 180
#define FRONT_PROBE_BED_POSITION 20
#define BACK_PROBE_BED_POSITION 180
#define XY_TRAVEL_SPEED 10000 // X and Y axis travel speed between probes, in mm/min
//If you have enabled the Auto Bed Levelling and are using the same Z Probe for Z Homing,
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
//#define Z_SAFE_HOMING
#ifdef Z_SAFE_HOMING
#define Z_SAFE_HOMING_X_POINT (X_MAX_LENGTH/2) // X point for Z homing when homing all axis (G28) or homing Z
#define Z_SAFE_HOMING_Y_POINT (Y_MAX_LENGTH/2) // Y point for Z homing when homing all axis (G28) or homing Z
#endif
//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (ABL)
//#define Z_PROBE_REPEATABILITY_TEST // Delete the comment to enable
#ifdef ENABLE_AUTO_BED_LEVELING
// There are 2 different ways to specify probing locations
//
// - "grid" mode
// Probe several points in a rectangular grid.
// You specify the rectangle and the density of sample points.
// This mode is preferred because there are more measurements.
//
// - "3-point" mode
// Probe 3 arbitrary points on the bed (that aren't colinear)
// You specify the XY coordinates of all 3 points.
// Enable this to sample the bed in a grid (least squares solution)
// Note: this feature generates 10KB extra code size
#define AUTO_BED_LEVELING_GRID
#ifdef AUTO_BED_LEVELING_GRID
#define MIN_PROBE_EDGE 10 // The probe square sides can be no smaller than this
// Set the number of grid points per dimension
// You probably don't need more than 3 (squared=9)
#define AUTO_BED_LEVELING_GRID_POINTS 2
#else // not AUTO_BED_LEVELING_GRID
// Arbitrary points to probe. A simple cross-product
// is used to estimate the plane of the bed.
#define ABL_PROBE_PT_1_X 15
#define ABL_PROBE_PT_1_Y 180
#define ABL_PROBE_PT_2_X 15
#define ABL_PROBE_PT_2_Y 20
#define ABL_PROBE_PT_3_X 170
#define ABL_PROBE_PT_3_Y 20
#endif // AUTO_BED_LEVELING_GRID
// Offsets to the probe relative to the extruder tip (Hotend - Probe)
// X and Y offsets MUST be INTEGERS
#define X_PROBE_OFFSET_FROM_EXTRUDER 0 // Probe on: -left +right
#define Y_PROBE_OFFSET_FROM_EXTRUDER 0 // Probe on: -front +behind
#define Z_PROBE_OFFSET_FROM_EXTRUDER -1 // -below (always!)
#define Z_RAISE_BEFORE_HOMING 10 // (in mm) Raise Z before homing (G28) for Probe Clearance.
// Be sure you have this distance over your Z_MAX_POS in case
#define Z_RAISE_BEFORE_PROBING 10 //How much the extruder will be raised before travelling to the first probing point.
#define Z_RAISE_BETWEEN_PROBINGS 5 //How much the extruder will be raised when travelling from between next probing points
#define Z_RAISE_AFTER_PROBING 5 //How much the extruder will be raised after the last probing point.
//#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
//#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pick up the sled. 0 should be fine but you can push it further if you'd like.
//If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
//The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
//You MUST HAVE the SERVO ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile.
//#define PROBE_SERVO_DEACTIVATION_DELAY 300
#endif // ENABLE_AUTO_BED_LEVELING
// The position of the homing switches
//#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
//Manual homing switch locations:
#ifdef MANUAL_HOME_POSITIONS
#define MANUAL_X_HOME_POS 0
#define MANUAL_Y_HOME_POS 0
#define MANUAL_Z_HOME_POS 0
#endif
// MOVEMENT SETTINGS
#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
#define HOMING_FEEDRATE {100*60,100*60,2*60,0} // set the homing speeds (mm/min)
// default settings
#define DEFAULT_AXIS_STEPS_PER_UNIT {80,80,3200,625,625,625,625} // X, Y, Z, E0, E1, E2, E3 default steps per unit
#define DEFAULT_MAX_FEEDRATE {300,300,2,100,100,100,100} // X, Y, Z, E0, E1, E2, E3 (mm/sec)
#define DEFAULT_RETRACTION_MAX_FEEDRATE {110,110,110,110} // E0, E1, E2, E3 (mm/sec)
#define DEFAULT_MAX_ACCELERATION {3000,3000,50,1000,1000,1000,1000} // X, Y, Z, E0, E1, E2, E3 maximum start speed for accelerated moves.
#define DEFAULT_ACCELERATION 2500 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
#define DEFAULT_RETRACT_ACCELERATION 10000 // E max acceleration in mm/s^2 for retracts
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
// For the other hotends it is their distance from the extruder 0 hotend.
//#define HOTEND_OFFSET_X {0.0, 5.00, 0.0, 0.0} // (in mm) for each extruder, offset of the hotend on the X axis
//#define HOTEND_OFFSET_Y {0.0, 5.00, 0.0, 0.0} // (in mm) for each extruder, offset of the hotend on the Y axis
// The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously)
#define DEFAULT_XYJERK 10.0 // (mm/sec)
#define DEFAULT_ZJERK 0.4 // (mm/sec)
#define DEFAULT_EJERK 5.0 // (mm/sec)
//===========================================================================
//=============================Additional Features===========================
//===========================================================================
// Custom M code points
//#define CUSTOM_M_CODES
#ifdef CUSTOM_M_CODES
#define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
#define Z_PROBE_OFFSET_RANGE_MIN -20
#define Z_PROBE_OFFSET_RANGE_MAX 20
#endif
MarlinKimbra/Configuration_Corexy.h deleted 100644 → 0
View file @ 0a201721
// Define this to set a custom name for your generic Mendel,
#define CUSTOM_MENDEL_NAME "Core XY"
//===========================================================================
//=============================Mechanical Settings===========================
//===========================================================================
// coarse Endstop Settings
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
#ifndef ENDSTOPPULLUPS
// fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined
// #define ENDSTOPPULLUP_XMAX
// #define ENDSTOPPULLUP_YMAX
// #define ENDSTOPPULLUP_ZMAX
// #define ENDSTOPPULLUP_XMIN
// #define ENDSTOPPULLUP_YMIN
// #define ENDSTOPPULLUP_ZMIN
// #define ENDSTOPPULLUP_EMIN
#endif
// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
const bool E_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
const bool X_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
const bool Y_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
// ENDSTOP SETTINGS:
// Sets direction of endstop when homing; 1=MAX, -1=MIN
#define X_HOME_DIR -1
#define Y_HOME_DIR -1
#define Z_HOME_DIR -1
#define E_HOME_DIR -1
#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
#define X_ENABLE_ON 0
#define Y_ENABLE_ON 0
#define Z_ENABLE_ON 0
#define E_ENABLE_ON 0 // For all extruder
// Disables axis when it's not being used.
#define DISABLE_X false
#define DISABLE_Y false
#define DISABLE_Z false
#define DISABLE_E false // For all extruder
#define DISABLE_INACTIVE_EXTRUDER false //disable only inactive extruder and keep active extruder enabled
// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
#define INVERT_X_DIR false
#define INVERT_Y_DIR false
#define INVERT_Z_DIR false
#define INVERT_E0_DIR false
#define INVERT_E1_DIR false
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
// Travel limits after homing (units are in mm)
#define X_MAX_POS 200
#define X_MIN_POS 0
#define Y_MAX_POS 200
#define Y_MIN_POS 0
#define Z_MAX_POS 200
#define Z_MIN_POS 0
#define E_MIN_POS 0
//=====================================================================================
//============================= Bed Manual or Auto Leveling ===========================
//=====================================================================================
// set the rectangle in which to probe in manual or automatic
#define LEFT_PROBE_BED_POSITION 20
#define RIGHT_PROBE_BED_POSITION 180
#define FRONT_PROBE_BED_POSITION 20
#define BACK_PROBE_BED_POSITION 180
#define XY_TRAVEL_SPEED 10000 // X and Y axis travel speed between probes, in mm/min
//If you have enabled the Auto Bed Levelling and are using the same Z Probe for Z Homing,
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
//#define Z_SAFE_HOMING
#ifdef Z_SAFE_HOMING
#define Z_SAFE_HOMING_X_POINT (X_MAX_LENGTH/2) // X point for Z homing when homing all axis (G28) or homing Z
#define Z_SAFE_HOMING_Y_POINT (Y_MAX_LENGTH/2) // Y point for Z homing when homing all axis (G28) or homing Z
#endif
//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (ABL)
//#define Z_PROBE_REPEATABILITY_TEST // Delete the comment to enable
#ifdef ENABLE_AUTO_BED_LEVELING
// There are 2 different ways to specify probing locations
//
// - "grid" mode
// Probe several points in a rectangular grid.
// You specify the rectangle and the density of sample points.
// This mode is preferred because there are more measurements.
//
// - "3-point" mode
// Probe 3 arbitrary points on the bed (that aren't colinear)
// You specify the XY coordinates of all 3 points.
// Enable this to sample the bed in a grid (least squares solution)
// Note: this feature generates 10KB extra code size
#define AUTO_BED_LEVELING_GRID
#ifdef AUTO_BED_LEVELING_GRID
#define MIN_PROBE_EDGE 10 // The probe square sides can be no smaller than this
// Set the number of grid points per dimension
// You probably don't need more than 3 (squared=9)
#define AUTO_BED_LEVELING_GRID_POINTS 2
#else // not AUTO_BED_LEVELING_GRID
// Arbitrary points to probe. A simple cross-product
// is used to estimate the plane of the bed.
#define ABL_PROBE_PT_1_X 15
#define ABL_PROBE_PT_1_Y 180
#define ABL_PROBE_PT_2_X 15
#define ABL_PROBE_PT_2_Y 20
#define ABL_PROBE_PT_3_X 170
#define ABL_PROBE_PT_3_Y 20
#endif // AUTO_BED_LEVELING_GRID
// Offsets to the probe relative to the extruder tip (Hotend - Probe)
// X and Y offsets must be integers
#define X_PROBE_OFFSET_FROM_EXTRUDER 0 // Probe on: -left +right
#define Y_PROBE_OFFSET_FROM_EXTRUDER 0 // Probe on: -front +behind
#define Z_PROBE_OFFSET_FROM_EXTRUDER -1 // -below (always!)
#define Z_RAISE_BEFORE_HOMING 10 // (in mm) Raise Z before homing (G28) for Probe Clearance.
// Be sure you have this distance over your Z_MAX_POS in case
#define Z_RAISE_BEFORE_PROBING 10 //How much the extruder will be raised before travelling to the first probing point.
#define Z_RAISE_BETWEEN_PROBINGS 5 //How much the extruder will be raised when travelling from between next probing points
#define Z_RAISE_AFTER_PROBING 5 //How much the extruder will be raised after the last probing point.
//#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
//#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pick up the sled. 0 should be fine but you can push it further if you'd like.
//If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
//The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
//You MUST HAVE the SERVO ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile.
//#define PROBE_SERVO_DEACTIVATION_DELAY 300
#endif // ENABLE_AUTO_BED_LEVELING
// The position of the homing switches
//#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
//Manual homing switch locations:
#ifdef MANUAL_HOME_POSITIONS
#define MANUAL_X_HOME_POS 0
#define MANUAL_Y_HOME_POS 0
#define MANUAL_Z_HOME_POS 0
#endif
// MOVEMENT SETTINGS
#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
#define HOMING_FEEDRATE {100*60,100*60,2*60,0} // set the homing speeds (mm/min)
// default settings
#define DEFAULT_AXIS_STEPS_PER_UNIT {80,80,3200,625,625,625,625} // X, Y, Z, E0, E1, E2, E3 default steps per unit
#define DEFAULT_MAX_FEEDRATE {300,300,2,100,100,100,100} // X, Y, Z, E0, E1, E2, E3 (mm/sec)
#define DEFAULT_RETRACTION_MAX_FEEDRATE {110,110,110,110} // E0, E1, E2, E3 (mm/sec)
#define DEFAULT_MAX_ACCELERATION {3000,3000,50,1000,1000,1000,1000} // X, Y, Z, E0, E1, E2, E3 maximum start speed for accelerated moves.
#define DEFAULT_ACCELERATION 2500 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
#define DEFAULT_RETRACT_ACCELERATION 10000 // E max acceleration in mm/s^2 for retracts
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
// For the other hotends it is their distance from the extruder 0 hotend.
//#define HOTEND_OFFSET_X {0.0, 5.00, 0.0, 0.0} // (in mm) for each extruder, offset of the hotend on the X axis
//#define HOTEND_OFFSET_Y {0.0, 5.00, 0.0, 0.0} // (in mm) for each extruder, offset of the hotend on the Y axis
// The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously)
#define DEFAULT_XYJERK 10.0 // (mm/sec)
#define DEFAULT_ZJERK 0.4 // (mm/sec)
#define DEFAULT_EJERK 5.0 // (mm/sec)
//===========================================================================
//=============================Additional Features===========================
//===========================================================================
// Custom M code points
//#define CUSTOM_M_CODES
#ifdef CUSTOM_M_CODES
#define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
#define Z_PROBE_OFFSET_RANGE_MIN -20
#define Z_PROBE_OFFSET_RANGE_MAX 20
#endif
MarlinKimbra/Configuration_Delta.h deleted 100644 → 0
View file @ 0a201721
// Define this to set a custom name for your generic Delta
#define CUSTOM_MENDEL_NAME "Delta"
//===========================================================================
//============================== Delta Settings =============================
//===========================================================================
// Make delta curves from many straight lines (linear interpolation).
// This is a trade-off between visible corners (not enough segments)
// and processor overload (too many expensive sqrt calls).
#define DELTA_SEGMENTS_PER_SECOND 200
// Center-to-center distance of the holes in the diagonal push rods.
#define DEFAULT_DELTA_DIAGONAL_ROD 217.0 // mm
// Horizontal offset from middle of printer to smooth rod center.
#define DELTA_SMOOTH_ROD_OFFSET 145.0 // mm
// Horizontal offset of the universal joints on the end effector.
#define DELTA_EFFECTOR_OFFSET 20.0 // mm
// Horizontal offset of the universal joints on the carriages.
#define DELTA_CARRIAGE_OFFSET 20.0 // mm
// Bed Printer radius
#define PRINTER_RADIUS 70 // mm
//Uncomment to enable autocalibration debug messages
#define DEBUG_MESSAGES
// Precision for G30 delta autocalibration function
#define AUTOCALIBRATION_PRECISION 0.1 // mm
// Effective horizontal distance bridged by diagonal push rods.
#define DEFAULT_DELTA_RADIUS (DELTA_SMOOTH_ROD_OFFSET-DELTA_EFFECTOR_OFFSET-DELTA_CARRIAGE_OFFSET)
// Z-Probe variables
// Start and end location values are used to deploy/retract the probe (will move from start to end and back again)
#define PROBING_FEEDRATE 500 // Speed for individual probe Use: G30 A F600
#define Z_PROBE_OFFSET {0,0,-1,0} // X, Y, Z, E distance between hotend nozzle and deployed bed leveling probe.
#define Z_PROBE_DEPLOY_START_LOCATION {0,0,30,0} // X, Y, Z, E start location for z-probe deployment sequence
#define Z_PROBE_DEPLOY_END_LOCATION {0,0,30,0} // X, Y, Z, E end location for z-probe deployment sequence
#define Z_PROBE_RETRACT_START_LOCATION {0,0,30,0}// X, Y, Z, E start location for z-probe retract sequence
#define Z_PROBE_RETRACT_END_LOCATION {0,0,30,0} // X, Y, Z, E end location for z-probe retract sequence
#define AUTOLEVEL_GRID 20 // Distance between autolevel Z probing points, should be less than print surface radius/3.
//===========================================================================
//=============================Mechanical Settings===========================
//===========================================================================
// coarse Endstop Settings
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
#ifndef ENDSTOPPULLUPS
// fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined
// #define ENDSTOPPULLUP_XMAX
// #define ENDSTOPPULLUP_YMAX
// #define ENDSTOPPULLUP_ZMAX
// #define ENDSTOPPULLUP_XMIN
// #define ENDSTOPPULLUP_YMIN
// #define ENDSTOPPULLUP_ZMIN
// #define ENDSTOPPULLUP_EMIN
#endif
#ifdef ENDSTOPPULLUPS
#define ENDSTOPPULLUP_XMAX
#define ENDSTOPPULLUP_YMAX
#define ENDSTOPPULLUP_ZMAX
#define ENDSTOPPULLUP_XMIN
#define ENDSTOPPULLUP_YMIN
#define ENDSTOPPULLUP_ZMIN
#define ENDSTOPPULLUP_EMIN
#endif
// The pullups are needed if you directly connect a mechanical end switch between the signal and ground pins.
const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
const bool E_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
const bool X_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
const bool Y_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
// ENDSTOP SETTINGS:
// Sets direction of endstop when homing; 1=MAX, -1=MIN
#define X_HOME_DIR 1 //DELTA MUST HAVE MAX ENDSTOP
#define Y_HOME_DIR 1 //DELTA MUST HAVE MAX ENDSTOP
#define Z_HOME_DIR 1 //DELTA MUST HAVE MAX ENDSTOP
#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
#define X_ENABLE_ON 0
#define Y_ENABLE_ON 0
#define Z_ENABLE_ON 0
#define E_ENABLE_ON 0 // For all extruder
// Disables axis when it's not being used.
#define DISABLE_X false
#define DISABLE_Y false
#define DISABLE_Z false
#define DISABLE_E false // For all extruder
#define DISABLE_INACTIVE_EXTRUDER false //disable only inactive extruder and keep active extruder enabled
// If you motor turns to wrong direction, you can invert it here:
#define INVERT_X_DIR false
#define INVERT_Y_DIR false
#define INVERT_Z_DIR false
#define INVERT_E0_DIR false
#define INVERT_E1_DIR false
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
// The position of the homing switches
#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
//Manual homing switch locations:
#define MANUAL_X_HOME_POS 0
#define MANUAL_Y_HOME_POS 0
#define MANUAL_Z_HOME_POS 205 // Distance between nozzle and print surface after homing.
// Travel limits after homing
#define X_MAX_POS PRINTER_RADIUS
#define X_MIN_POS -PRINTER_RADIUS
#define Y_MAX_POS PRINTER_RADIUS
#define Y_MIN_POS -PRINTER_RADIUS
#define Z_MAX_POS MANUAL_Z_HOME_POS
#define Z_MIN_POS 0
#define E_MIN_POS 0
//// MOVEMENT SETTINGS
#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
#define HOMING_FEEDRATE {100*60,100*60,100*60,0} // set the homing speeds (mm/min)
// default settings
// delta speeds must be the same on xyz
#define DEFAULT_AXIS_STEPS_PER_UNIT {80,80,80,451,625,625,625} // X, Y, Z, E0, E1, E2, E3
#define DEFAULT_MAX_FEEDRATE {300,300,300,45,100,100,100} // X, Y, Z, E0, E1, E2, E3 (mm/sec)
#define DEFAULT_RETRACTION_MAX_FEEDRATE {150,150,150,150} // E0, E1, E2, E3 (mm/sec)
#define DEFAULT_MAX_ACCELERATION {2000,2000,2000,1000,1000,1000,1000} // X, Y, Z, E0, E1, E2, E3 maximum start speed for accelerated moves.
#define DEFAULT_ACCELERATION 1000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
#define DEFAULT_RETRACT_ACCELERATION 2500 // X, Y, Z and E max acceleration in mm/s^2 for retracts
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
// For the other hotends it is their distance from the extruder 0 hotend.
//#define HOTEND_OFFSET_X {0.0, 5.00, 0.0, 0.0} // (in mm) for each extruder, offset of the hotend on the X axis
//#define HOTEND_OFFSET_Y {0.0, 5.00, 0.0, 0.0} // (in mm) for each extruder, offset of the hotend on the Y axis
// The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously)
#define DEFAULT_XYJERK 20 // (mm/sec)
#define DEFAULT_ZJERK 20 // (mm/sec)
#define DEFAULT_EJERK 5 // (mm/sec)
MarlinKimbra/Configuration_Scara.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/Configuration_adv.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/DOGMbitmaps.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/LiquidCrystalRus.cpp deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/LiquidCrystalRus.h deleted 100644 → 0
View file @ 0a201721
//
// based on LiquidCrystal library from ArduinoIDE, see http://arduino.cc
// modified 27 Jul 2011
// by Ilya V. Danilov http://mk90.ru/
//
#ifndef LiquidCrystalRus_h
#define LiquidCrystalRus_h
#include <inttypes.h>
#include "Print.h"
// commands
#define LCD_CLEARDISPLAY 0x01
#define LCD_RETURNHOME 0x02
#define LCD_ENTRYMODESET 0x04
#define LCD_DISPLAYCONTROL 0x08
#define LCD_CURSORSHIFT 0x10
#define LCD_FUNCTIONSET 0x20
#define LCD_SETCGRAMADDR 0x40
#define LCD_SETDDRAMADDR 0x80
// flags for display entry mode
#define LCD_ENTRYRIGHT 0x00
#define LCD_ENTRYLEFT 0x02
#define LCD_ENTRYSHIFTINCREMENT 0x01
#define LCD_ENTRYSHIFTDECREMENT 0x00
// flags for display on/off control
#define LCD_DISPLAYON 0x04
#define LCD_DISPLAYOFF 0x00
#define LCD_CURSORON 0x02
#define LCD_CURSOROFF 0x00
#define LCD_BLINKON 0x01
#define LCD_BLINKOFF 0x00
// flags for display/cursor shift
#define LCD_DISPLAYMOVE 0x08
#define LCD_CURSORMOVE 0x00
#define LCD_MOVERIGHT 0x04
#define LCD_MOVELEFT 0x00
// flags for function set
#define LCD_8BITMODE 0x10
#define LCD_4BITMODE 0x00
#define LCD_2LINE 0x08
#define LCD_1LINE 0x00
#define LCD_5x10DOTS 0x04
#define LCD_5x8DOTS 0x00
// enum for
#define LCD_DRAM_Normal 0x00
#define LCD_DRAM_WH1601 0x01
class LiquidCrystalRus : public Print {
public:
LiquidCrystalRus(uint8_t rs, uint8_t enable,
uint8_t d0, uint8_t d1, uint8_t d2, uint8_t d3,
uint8_t d4, uint8_t d5, uint8_t d6, uint8_t d7);
LiquidCrystalRus(uint8_t rs, uint8_t rw, uint8_t enable,
uint8_t d0, uint8_t d1, uint8_t d2, uint8_t d3,
uint8_t d4, uint8_t d5, uint8_t d6, uint8_t d7);
LiquidCrystalRus(uint8_t rs, uint8_t rw, uint8_t enable,
uint8_t d0, uint8_t d1, uint8_t d2, uint8_t d3);
LiquidCrystalRus(uint8_t rs, uint8_t enable,
uint8_t d0, uint8_t d1, uint8_t d2, uint8_t d3);
void init(uint8_t fourbitmode, uint8_t rs, uint8_t rw, uint8_t enable,
uint8_t d0, uint8_t d1, uint8_t d2, uint8_t d3,
uint8_t d4, uint8_t d5, uint8_t d6, uint8_t d7);
void begin(uint8_t cols, uint8_t rows, uint8_t charsize = LCD_5x8DOTS);
void clear();
void home();
void noDisplay();
void display();
void noBlink();
void blink();
void noCursor();
void cursor();
void scrollDisplayLeft();
void scrollDisplayRight();
void leftToRight();
void rightToLeft();
void autoscroll();
void noAutoscroll();
void createChar(uint8_t, uint8_t[]);
void setCursor(uint8_t, uint8_t);
#if defined(ARDUINO) && ARDUINO >= 100
virtual size_t write(uint8_t);
using Print::write;
#else
virtual void write(uint8_t);
#endif
void command(uint8_t);
void setDRAMModel(uint8_t);
private:
void send(uint8_t, uint8_t);
void writeNbits(uint8_t, uint8_t);
uint8_t recv(uint8_t);
uint8_t readNbits(uint8_t);
void pulseEnable();
uint8_t _rs_pin; // LOW: command. HIGH: character.
uint8_t _rw_pin; // LOW: write to LCD. HIGH: read from LCD.
uint8_t _enable_pin; // activated by a HIGH pulse.
uint8_t _data_pins[8];
uint8_t _displayfunction;
uint8_t _displaycontrol;
uint8_t _displaymode;
uint8_t _initialized;
uint8_t _numlines,_currline;
uint8_t _dram_model;
uint8_t utf_hi_char; // UTF-8 high part
};
#endif
MarlinKimbra/Makefile deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/Marlin.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/MarlinKimbra.ino deleted 100644 → 0
View file @ 0a201721
/* -*- c++ -*- */
/*
Reprap firmware based on Sprinter and grbl.
Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
This program is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
/*
This firmware is a mashup between Sprinter and grbl.
(https://github.com/kliment/Sprinter)
(https://github.com/simen/grbl/tree)
It has preliminary support for Matthew Roberts advance algorithm
http://reprap.org/pipermail/reprap-dev/2011-May/003323.html
*/
/* All the implementation is done in *.cpp files to get better compatibility with avr-gcc without the Arduino IDE */
/* Use this file to help the Arduino IDE find which Arduino libraries are needed and to keep documentation on GCode */
#include "Configuration.h"
#include "pins.h"
#ifdef ULTRA_LCD
#if defined(LCD_I2C_TYPE_PCF8575)
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
#elif defined(LCD_I2C_TYPE_MCP23017) || defined(LCD_I2C_TYPE_MCP23008)
#include <Wire.h>
#include <LiquidTWI2.h>
#elif defined(DOGLCD)
#include <U8glib.h> // library for graphics LCD by Oli Kraus (https://code.google.com/p/u8glib/)
#else
#include <LiquidCrystal.h> // library for character LCD
#endif
#endif
#if defined(DIGIPOTSS_PIN) && DIGIPOTSS_PIN > -1
#include <SPI.h>
#endif
#if defined(DIGIPOT_I2C)
#include <Wire.h>
#endif
MarlinKimbra/MarlinSerial.cpp deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/MarlinSerial.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/Marlin_main.cpp deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/SanityCheck.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/Sd2Card.cpp deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/Sd2Card.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/Sd2PinMap.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/SdBaseFile.cpp deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/SdBaseFile.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/SdFatConfig.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/SdFatStructs.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/SdFatUtil.cpp deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/SdFatUtil.h deleted 100644 → 0
View file @ 0a201721
/* Arduino SdFat Library
* Copyright (C) 2008 by William Greiman
*
* This file is part of the Arduino SdFat Library
*
* This Library is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This Library is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
* You should have received a copy of the GNU General Public License
* along with the Arduino SdFat Library. If not, see
* <http://www.gnu.org/licenses/>.
*/
#include "Marlin.h"
#ifdef SDSUPPORT
#ifndef SdFatUtil_h
#define SdFatUtil_h
/**
* \file
* \brief Useful utility functions.
*/
#include "Marlin.h"
#include "MarlinSerial.h"
/** Store and print a string in flash memory.*/
#define PgmPrint(x) SerialPrint_P(PSTR(x))
/** Store and print a string in flash memory followed by a CR/LF.*/
#define PgmPrintln(x) SerialPrintln_P(PSTR(x))
namespace SdFatUtil {
int FreeRam();
void print_P( PGM_P str);
void println_P( PGM_P str);
void SerialPrint_P(PGM_P str);
void SerialPrintln_P(PGM_P str);
}
using namespace SdFatUtil; // NOLINT
#endif // #define SdFatUtil_h
#endif
\ No newline at end of file
MarlinKimbra/SdFile.cpp deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/SdFile.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/SdInfo.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/SdVolume.cpp deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/SdVolume.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/Servo.cpp deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/Servo.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/boards.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/cardreader.cpp deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/cardreader.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/digipot_mcp4451.cpp deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/dogm_font_data_6x9_marlin.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/dogm_font_data_HD44780_C.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/dogm_font_data_HD44780_J.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/dogm_font_data_HD44780_W.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/dogm_font_data_ISO10646_1.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/dogm_font_data_ISO10646_5_Cyrillic.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/dogm_font_data_ISO10646_Kana.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/dogm_font_data_Marlin_symbols.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/dogm_lcd_implementation.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/fastio.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/firmware_test.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/fonts/Marlin_symbols.fon deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/fonts/README.fonts deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/fonts/bdf2u8g.exe deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/fonts/make_fonts.bat deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/language.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/language_an.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/language_ca.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/language_de.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/language_en.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/language_es.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/language_eu.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/language_fi.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/language_fr.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/language_it.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/language_kana.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/language_kana_utf8.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/language_nl.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/language_pl.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/language_pt-br.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/language_pt.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/language_ru.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/language_test.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/motion_control.cpp deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/motion_control.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/pins.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/pins2tool.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/planner.cpp deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/planner.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/qr_solve.cpp deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/qr_solve.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/scripts/createTemperatureLookupMarlin.py deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/scripts/create_speed_lookuptable.py deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/scripts/g29_auto.py deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/speed_lookuptable.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/stepper.cpp deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/stepper.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/stepper_indirection.cpp deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/stepper_indirection.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/temperature.cpp deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/temperature.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/thermistortables.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/ultralcd.cpp deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/ultralcd.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/ultralcd_implementation_hitachi_HD44780.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/ultralcd_st7920_u8glib_rrd.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/utf_mapper.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/vector_3.cpp deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/vector_3.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/watchdog.cpp deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
MarlinKimbra/watchdog.h deleted 100644 → 0
View file @ 0a201721
This diff is collapsed.
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment