//#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2,3)
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2,3)
//#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel
//#define MEASURED_UPPER_LIMIT 2.00 //upper limit factor used for sensor reading validation in mm
//#define MEASURED_LOWER_LIMIT 1.35 //lower limit factor for sensor reading validation in mm
#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation
//#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM)
#define MEASURED_UPPER_LIMIT 2.00 //upper limit factor used for sensor reading validation in mm
#define MEASURED_LOWER_LIMIT 1.35 //lower limit factor for sensor reading validation in mm
#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM)
//defines used in the code
//defines used in the code
#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially
//#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially
//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec.
//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec.
//#define POWER_EFFICIENCY 100.0 //(%) The power efficency of the power supply
#define POWER_EFFICIENCY 100.0 //(%) The power efficency of the power supply
//When using an LCD, uncomment the line below to display the Power consumption sensor data on the last line instead of status. Status will appear for 5 sec.
//When using an LCD, uncomment the line below to display the Power consumption sensor data on the last line instead of status. Status will appear for 5 sec.
//#define POWER_CONSUMPTION_LCD_DISPLAY
//#define POWER_CONSUMPTION_LCD_DISPLAY
...
@@ -1024,10 +1034,10 @@
...
@@ -1024,10 +1034,10 @@
//This enable the firmware to write some configuration that require frequent update, on the SD card
//This enable the firmware to write some configuration that require frequent update, on the SD card
//#define SD_SETTINGS //Uncomment to enable
//#define SD_SETTINGS //Uncomment to enable
#define SD_CFG_SECONDS 300 //seconds between update
//#define SD_CFG_SECONDS 300 //seconds between update
#define CFG_SD_FILE "INFO.CFG" //name of the configuration file
//#define CFG_SD_FILE "INFO.CFG" //name of the configuration file
#define CFG_SD_MAX_KEY_LEN 3+1 //icrease this if you add key name longer than the actual value.
//#define CFG_SD_MAX_KEY_LEN 3+1 //icrease this if you add key name longer than the actual value.
#define CFG_SD_MAX_VALUE_LEN 12+1 //this should be enought for int, long and float if you need to retrive strings increase this carefully
//#define CFG_SD_MAX_VALUE_LEN 12+1 //this should be enought for int, long and float if you need to retrive strings increase this carefully
