Update 4.1.2 beta

NOT TESTED

MarlinKimbra/MarlinSerial.h

@@ -23,10 +23,6 @@
 #define MarlinSerial_h
 #include "Marlin.h"
 
-#ifndef SERIAL_PORT
-  #define SERIAL_PORT 0
-#endif
-
 // The presence of the UBRRH register is used to detect a UART.
 #define UART_PRESENT(port) ((port == 0 && (defined(UBRRH) || defined(UBRR0H))) || \
             (port == 1 && defined(UBRR1H)) || (port == 2 && defined(UBRR2H)) || \

MarlinKimbra/Marlin_main.cpp

@@ -290,7 +290,11 @@ const int sensitive_pins[] = SENSITIVE_PINS; ///< Sensitive pin list for M42
 // Inactivity shutdown
 millis_t previous_cmd_ms = 0;
 static millis_t max_inactive_time = 0;
-static millis_t stepper_inactive_time = DEFAULT_STEPPER_DEACTIVE_TIME * 1000L;
+#if ENABLED(DEFAULT_STEPPER_DEACTIVE_TIME)
+  static millis_t stepper_inactive_time = DEFAULT_STEPPER_DEACTIVE_TIME * 1000L;
+#else
+  static millis_t stepper_inactive_time = 0;
+#endif
 millis_t print_job_start_ms = 0; ///< Print job start time
 millis_t print_job_stop_ms = 0;  ///< Print job stop time
 static uint8_t target_extruder;
@@ -5151,7 +5155,11 @@ inline void gcode_M140() {
         case 0:
           if (code_seen('H')) {
             v = code_value_short();
-            plaPreheatHotendTemp = constrain(v, EXTRUDE_MINTEMP, HEATER_0_MAXTEMP - 15);
+            #if ENABLED(PREVENT_DANGEROUS_EXTRUDE)
+              plaPreheatHotendTemp = constrain(v, EXTRUDE_MINTEMP, HEATER_0_MAXTEMP - 15);
+            #else
+              plaPreheatHotendTemp = constrain(v, HEATER_0_MINTEMP, HEATER_0_MAXTEMP - 15);
+            #endif
           }
           if (code_seen('F')) {
             v = code_value_short();
@@ -5167,7 +5175,11 @@ inline void gcode_M140() {
         case 1:
           if (code_seen('H')) {
             v = code_value_short();
-            absPreheatHotendTemp = constrain(v, EXTRUDE_MINTEMP, HEATER_0_MAXTEMP - 15);
+            #if ENABLED(PREVENT_DANGEROUS_EXTRUDE)
+              absPreheatHotendTemp = constrain(v, EXTRUDE_MINTEMP, HEATER_0_MAXTEMP - 15);
+            #else
+              absPreheatHotendTemp = constrain(v, HEATER_0_MINTEMP, HEATER_0_MAXTEMP - 15);
+            #endif
           }
           if (code_seen('F')) {
             v = code_value_short();
@@ -5183,7 +5195,11 @@ inline void gcode_M140() {
         case 2:
           if (code_seen('H')) {
             v = code_value_short();
-            gumPreheatHotendTemp = constrain(v, EXTRUDE_MINTEMP, HEATER_0_MAXTEMP - 15);
+            #if ENABLED(PREVENT_DANGEROUS_EXTRUDE)
+              gumPreheatHotendTemp = constrain(v, EXTRUDE_MINTEMP, HEATER_0_MAXTEMP - 15);
+            #else
+              gumPreheatHotendTemp = constrain(v, HEATER_0_MINTEMP, HEATER_0_MAXTEMP - 15);
+            #endif
           }
           if (code_seen('F')) {
             v = code_value_short();
@@ -7102,7 +7118,7 @@ void ok_to_send() {
 }
 
 void clamp_to_software_endstops(float target[3]) {
-  if (min_software_endstops) {
+  if (SOFTWARE_MIN_ENDSTOPS) {
     NOLESS(target[X_AXIS], min_pos[X_AXIS]);
     NOLESS(target[Y_AXIS], min_pos[Y_AXIS]);
     
@@ -7114,7 +7130,7 @@ void clamp_to_software_endstops(float target[3]) {
     NOLESS(target[Z_AXIS], min_pos[Z_AXIS] + negative_z_offset);
   }
 
-  if (max_software_endstops) {
+  if (SOFTWARE_MAX_ENDSTOPS) {
     NOMORE(target[X_AXIS], max_pos[X_AXIS]);
     NOMORE(target[Y_AXIS], max_pos[Y_AXIS]);
     NOMORE(target[Z_AXIS], max_pos[Z_AXIS]);

MarlinKimbra/configuration_basic.h

@@ -151,7 +151,7 @@
 
 // Use it for Testing or Development purposes. NEVER for production machine.
 //#define DUMMY_THERMISTOR_998_VALUE 25
-//#define DUMMY_THERMISTOR_999_VALUE 100
+//#define DUMMY_THERMISTOR_999_VALUE 25
 
 //Show Temperature ADC value
 //The M105 command return, besides traditional information, the ADC value read from temperature sensors.
@@ -233,7 +233,7 @@
  * 14 Portuguese (Brazil)                                              * 
  *                                                                     * 
  ***********************************************************************/
-#define LANGUAGE_CHOICE 7
+#define LANGUAGE_CHOICE 1
 /***********************************************************************/
 
 

MarlinKimbra/configuration_feature.h

@@ -313,7 +313,7 @@
 // Multiple extruders can be assigned to the same pin in which case
 // the fan will turn on when any selected extruder is above the threshold.
 // You need to set _AUTO_FAN_PIN in pins.h
-//#define EXTRUDER_AUTO_TEMPERATURE
+//#define EXTRUDER_AUTO_FAN
 #define EXTRUDER_AUTO_FAN_TEMPERATURE 50
 #define EXTRUDER_AUTO_FAN_SPEED 255  // 255 = full speed
 #define EXTRUDER_AUTO_FAN_MIN_SPEED 0
@@ -419,8 +419,7 @@
  *                                                                     *
  ***********************************************************************/
 //#define IDLE_OOZING_PREVENT
-#define IDLE_OOZING_MINTEMP           EXTRUDE_MINTEMP + 5
-#define IDLE_OOZING_MAXTEMP           IDLE_OOZING_MINTEMP + 5
+#define IDLE_OOZING_MINTEMP           190
 #define IDLE_OOZING_FEEDRATE          50    //default feedrate for retracting (mm/s)
 #define IDLE_OOZING_SECONDS           5
 #define IDLE_OOZING_LENGTH            15    //default retract length (positive mm)
@@ -476,6 +475,8 @@
  * Hooke's law says:    force = k * distance                                             *
  * Bernoulli's principle says:  v ^ 2 / 2 + g . h + pressure / density = constant        *
  * so: v ^ 2 is proportional to number of steps we advance the extruder                  *
+ *                                                                                       *
+ * This feature is obsolate needs update                                                 *
  * Uncomment ADVANCE to enable this feature                                              *
  *                                                                                       *
  *****************************************************************************************/
@@ -515,8 +516,8 @@
 /**************************************************************************
  *************************** Software endstops ****************************
  **************************************************************************/
-#define min_software_endstops true  // If true, axis won't move to coordinates less than HOME_POS.
-#define max_software_endstops true  // If true, axis won't move to coordinates greater than the defined lengths below.
+#define SOFTWARE_MIN_ENDSTOPS true  // If true, axis won't move to coordinates less than HOME_POS.
+#define SOFTWARE_MAX_ENDSTOPS true  // If true, axis won't move to coordinates greater than the defined lengths below.
 /***********************************************************************/
 
 
@@ -752,8 +753,8 @@
  *                                                                        *
  **************************************************************************/
 //#define BABYSTEPPING
-#define BABYSTEP_XY  // not only z, but also XY in the menu. more clutter, more functions
-                     // not implemented for CoreXY and deltabots!
+//#define BABYSTEP_XY  // not only z, but also XY in the menu. more clutter, more functions
+                       // not implemented for CoreXY and deltabots!
 #define BABYSTEP_INVERT_Z false     // true for inverse movements in Z
 #define BABYSTEP_Z_MULTIPLICATOR 2  // faster z movements
 /**************************************************************************/
@@ -810,11 +811,6 @@
 // without modifying the firmware (through the "M218 T1 X???" command).
 // Remember: you should set the second extruder x-offset to 0 in your slicer.
 
-// Pins for second x-carriage stepper driver (defined here to avoid further complicating pins.h)
-#define X2_ENABLE_PIN 29
-#define X2_STEP_PIN 25
-#define X2_DIR_PIN 23
-
 // There are a few selectable movement modes for dual x-carriages using M605 S<mode>
 //    Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results
 //                           as long as it supports dual x-carriages. (M605 S0)
@@ -849,7 +845,7 @@
  * On a RAMPS (or other 5 driver) motherboard, using this feature will limit you         *
  * to using 1 extruder.                                                                  *
  *                                                                                       *
- * Uncomment DUAL_X_CARRIAGE to enable this feature                                      *
+ * Uncomment Y_DUAL_STEPPER_DRIVERS to enable this feature                               *
  *                                                                                       *
  *****************************************************************************************/
 //#define Y_DUAL_STEPPER_DRIVERS
@@ -872,7 +868,7 @@
  * On a RAMPS (or other 5 driver) motherboard, using this feature will limit you         *
  * to using 1 extruder.                                                                  *
  *                                                                                       *
- * Uncomment DUAL_X_CARRIAGE to enable this feature                                      *
+ * Uncomment Z_DUAL_STEPPER_DRIVERS to enable this feature                               *
  *                                                                                       *
  *****************************************************************************************/
 //#define Z_DUAL_STEPPER_DRIVERS
@@ -1115,7 +1111,6 @@
 //#define STRING_SPLASH_LINE2 STRING_DISTRIBUTION_DATE    // will be shown during bootup in line 2
 #define SPLASH_SCREEN_DURATION 5000                       // SPLASH SCREEN duration in millisecond
 
-#define LCD_SCREEN_ROT_0       //No screen rotation for graphics display
 //#define LCD_SCREEN_ROT_90    //Rotate screen orientation for graphics display by 90 degree clockwise
 //#define LCD_SCREEN_ROT_180   //Rotate screen orientation for graphics display by 180 degree clockwise
 //#define LCD_SCREEN_ROT_270   //Rotate screen orientation for graphics display by 270 degree clockwise
@@ -1383,8 +1378,6 @@
  ***********************************************************************/
 //#define HAVE_TMCDRIVER
 
-#if ENABLED(HAVE_TMCDRIVER)
-
 //#define X_IS_TMC
 #define X_MAX_CURRENT 1000  //in mA
 #define X_SENSE_RESISTOR 91 //in mOhms
@@ -1492,21 +1485,18 @@
 #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E1_IS_L6470
-#define E1_MICROSTEPS 16     //number of microsteps 
 #define E1_MICROSTEPS 16     //number of microsteps
 #define E1_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
 #define E1_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
 #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E2_IS_L6470
-#define E2_MICROSTEPS 16     //number of microsteps 
 #define E2_MICROSTEPS 16     //number of microsteps
 #define E2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
 #define E2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
 #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E3_IS_L6470
-#define E3_MICROSTEPS 16     //number of microsteps   
 #define E3_MICROSTEPS 16     //number of microsteps
 #define E3_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
 #define E3_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
@@ -1533,7 +1523,7 @@
 // The values should not be less than 1
 #define NUM_POSITON_SLOTS 2
 
-#define dropsegments 5                      // everything with less than this number of steps will be ignored as move and joined with the next movement
+#define DROP_SEGMENTS 5                      // everything with less than this number of steps will be ignored as move and joined with the next movement
 #define DEFAULT_MINSEGMENTTIME        20000 // minimum time in microseconds that a movement needs to take if the buffer is emptied.
 
 // Arc interpretation settings:

MarlinKimbra/dependency.h

+#ifndef CONDITIONALS_H
+#define CONDITIONALS_H
+
+/*
+ * This configuration file contains defines that depend on configuration but are not editable.
+ *
+ * - Serial comunication type
+ * - Board type
+ * - Mechanism type
+ * - Thermistor type
+ * - Temperature limits
+ * - Extruders number
+ * - UI Language
+ *
+ */
+ 
+// Serial comunication
+#if DISABLED(SERIAL_PORT)
+  #error DEPENDENCY ERROR: Missing setting SERIAL_PORT
+#endif
+#if DISABLED(BAUDRATE)
+  #error DEPENDENCY ERROR: Missing setting BAUDRATE
+#endif
+#if DISABLED(MACHINE_UUID)
+	#error DEPENDENCY ERROR: Missing setting MACHINE_UUID
+#endif
+
+//board
+#if DISABLED(MOTHERBOARD)
+  #error DEPENDENCY ERROR: Missing setting MOTHERBOARD
+#endif
+
+//Mechanism
+#if DISABLED(MEACHANISM)
+  #error DEPENDENCY ERROR: Missing setting MECHANISM
+#endif
+
+//Power supply
+#if DISABLED(POWER_SUPPLY)
+  #error DEPENDENCY ERROR: Missing setting POWER_SUPPLY
+#endif
+
+//Thermistor
+#if DISABLED(TEMP_SENSOR_0)
+  #error DEPENDENCY ERROR: Missing setting TEMP_SENSOR_0
+#endif
+#if DISABLED(TEMP_SENSOR_1)
+  #error DEPENDENCY ERROR: Missing setting TEMP_SENSOR_1
+#endif
+#if DISABLED(TEMP_SENSOR_2)
+  #error DEPENDENCY ERROR: Missing setting TEMP_SENSOR_2
+#endif
+#if DISABLED(TEMP_SENSOR_3)
+  #error DEPENDENCY ERROR: Missing setting TEMP_SENSOR_3
+#endif
+#if DISABLED(TEMP_SENSOR_BED)
+  #error DEPENDENCY ERROR: Missing setting TEMP_SENSOR_BED
+#endif
+#if (THERMISTORHEATER_0 == 998) || (THERMISTORHEATER_1 == 998) || (THERMISTORHEATER_2 == 998) || (THERMISTORHEATER_3 == 998) || (THERMISTORBED == 998) //User defined table
+  #if DISABLED(DUMMY_THERMISTOR_998_VALUE)
+    #error DEPENDENCY ERROR: Missing setting DUMMY_THERMISTOR_998_VALUE
+  #endif
+#endif
+
+//Temperature
+/**
+ * Temperature defines
+ */
+#if ENABLED(TEMP_RESIDENCY_TIME)
+  #if DISABLED(TEMP_HYSTERESIS)
+    #error DEPENDENCY ERROR: Missing setting TEMP_HYSTERESIS
+  #endif
+  #if DISABLED(TEMP_WINDOW)
+    #error DEPENDENCY ERROR: Missing setting TEMP_WINDOW
+  #endif
+#endif
+#if TEMP_SENSOR_0 != 0
+  #if DISABLED(HEATER_0_MAXTEMP)
+    #error DEPENDENCY ERROR: Missing setting HEATER_0_MAXTEMP
+  #endif
+  #if DISABLED(HEATER_0_MINTEMP)
+    #error DEPENDENCY ERROR: Missing setting HEATER_0_MINTEMP
+  #endif
+#endif
+#if TEMP_SENSOR_1 != 0
+  #if DISABLED(HEATER_1_MAXTEMP)
+    #error DEPENDENCY ERROR: Missing setting HEATER_1_MAXTEMP
+  #endif
+  #if DISABLED(HEATER_0_MINTEMP)
+    #error DEPENDENCY ERROR: Missing setting HEATER_1_MINTEMP
+  #endif
+#endif
+#if TEMP_SENSOR_2 != 0
+  #if DISABLED(HEATER_2_MAXTEMP)
+    #error DEPENDENCY ERROR: Missing setting HEATER_2_MAXTEMP
+  #endif
+  #if DISABLED(HEATER_0_MINTEMP)
+    #error DEPENDENCY ERROR: Missing setting HEATER_2_MINTEMP
+  #endif
+#endif
+#if TEMP_SENSOR_3 != 0
+  #if DISABLED(HEATER_3_MAXTEMP)
+    #error DEPENDENCY ERROR: Missing setting HEATER_3_MAXTEMP
+  #endif
+  #if DISABLED(HEATER_0_MINTEMP)
+    #error DEPENDENCY ERROR: Missing setting HEATER_3_MINTEMP
+  #endif
+#endif
+#if TEMP_SENSOR_BED != 0
+  #if DISABLED(BED_MAXTEMP)
+    #error DEPENDENCY ERROR: Missing setting BED_MAXTEMP
+  #endif
+  #if DISABLED(HEATER_0_MINTEMP)
+    #error DEPENDENCY ERROR: Missing setting BED_MINTEMP
+  #endif
+#endif
+#if DISABLED(PLA_PREHEAT_HOTEND_TEMP)
+  #error DEPENDENCY ERROR: Missing setting PLA_PREHEAT_HOTEND_TEMP
+#endif
+#if DISABLED(PLA_PREHEAT_HPB_TEMP)
+  #error DEPENDENCY ERROR: Missing setting PLA_PREHEAT_HPB_TEMP
+#endif
+#if DISABLED(PLA_PREHEAT_FAN_SPEED)
+  #error DEPENDENCY ERROR: Missing setting PLA_PREHEAT_FAN_SPEED
+#endif
+#if DISABLED(ABS_PREHEAT_HOTEND_TEMP)
+  #error DEPENDENCY ERROR: Missing setting ABS_PREHEAT_HOTEND_TEMP
+#endif
+#if DISABLED(ABS_PREHEAT_HPB_TEMP)
+  #error DEPENDENCY ERROR: Missing setting ABS_PREHEAT_HPB_TEMP
+#endif
+#if DISABLED(ABS_PREHEAT_FAN_SPEED)
+  #error DEPENDENCY ERROR: Missing setting ABS_PREHEAT_FAN_SPEED
+#endif
+#if DISABLED(GUM_PREHEAT_HOTEND_TEMP)
+  #error DEPENDENCY ERROR: Missing setting GUM_PREHEAT_HOTEND_TEMP
+#endif
+#if DISABLED(GUM_PREHEAT_HPB_TEMP)
+  #error DEPENDENCY ERROR: Missing setting GUM_PREHEAT_HPB_TEMP
+#endif
+#if DISABLED(GUM_PREHEAT_FAN_SPEED)
+  #error DEPENDENCY ERROR: Missing setting GUM_PREHEAT_FAN_SPEED
+#endif
+
+//extruders
+#if DISABLED(EXTRUDERS)
+  #error DEPENDENCY ERROR: Missing setting EXTRUDERS
+#endif
+#if DISABLED(DRIVER_EXTRUDERS)
+  #error DEPENDENCY ERROR: Missing setting DRIVER_EXTRUDERS
+#endif
+
+//Language
+#if DISABLED(LANGUAGE_CHOICE)
+  #error DEPENDENCY ERROR: Missing setting LANGUAGE_CHOICE
+#endif
+
+///FEATURE
+
+//Temperature
+#if DISABLED(PID_MAX)
+  #error DEPENDENCY ERROR: Missing setting PID_MAX
+#endif
+#if DISABLED(MAX_BED_POWER)
+  #error DEPENDENCY ERROR: Missing setting MAX_BED_POWER
+#endif
+#if ENABLED(PIDTEMP) || ENABLED(PIDTEMPBED)
+  #if DISABLED(MAX_OVERSHOOT_PID_AUTOTUNE)
+    #error DEPENDENCY ERROR: Missing setting MAX_OVERSHOOT_PID_AUTOTUNE
+  #endif
+#endif
+#if ENABLED(PIDTEMP)
+  #if DISABLED(PID_OPENLOOP)
+    #error DEPENDENCY ERROR: Missing setting PID_FUNCTIONAL_RANGE
+  #endif
+  #if DISABLED(PID_INTEGRAL_DRIVE_MAX)
+    #error DEPENDENCY ERROR: Missing setting PID_INTEGRAL_DRIVE_MAX
+  #endif
+  #if DISABLED(DEFAULT_Kp)
+    #error DEPENDENCY ERROR: Missing setting DEFAULT_Kp
+  #endif
+  #if DISABLED(DEFAULT_Ki)
+    #error DEPENDENCY ERROR: Missing setting DEFAULT_Ki
+  #endif
+  #if DISABLED(DEFAULT_Kd)
+    #error DEPENDENCY ERROR: Missing setting DEFAULT_Kd
+  #endif
+#endif
+#if ENABLED(PIDTEMPBED)
+  #if DISABLED(PID_BED_INTEGRAL_DRIVE_MAX)
+    #error DEPENDENCY ERROR: Missing setting PID_BED_INTEGRAL_DRIVE_MAX
+  #endif
+  #if DISABLED(DEFAULT_bedKp)
+    #error DEPENDENCY ERROR: Missing setting DEFAULT_bedKp
+  #endif
+  #if DISABLED(DEFAULT_bedKi)
+    #error DEPENDENCY ERROR: Missing setting DEFAULT_bedKi
+  #endif
+  #if DISABLED(DEFAULT_bedKd)
+    #error DEPENDENCY ERROR: Missing setting DEFAULT_bedKd
+  #endif
+#endif
+#if ENABLED(BED_LIMIT_SWITCHING)
+  #if DISABLED(BED_HYSTERESIS)
+    #error DEPENDENCY ERROR: Missing setting BED_HYSTERESIS
+  #endif
+  #if DISABLED(BED_CHECK_INTERVAL)
+    #error DEPENDENCY ERROR: Missing setting BED_CHECK_INTERVAL
+  #endif
+#endif
+#if ENABLED(THERMAL_PROTECTION_HOTENDS)
+  #if DISABLED(THERMAL_PROTECTION_PERIOD)
+    #error DEPENDENCY ERROR: Missing setting THERMAL_PROTECTION_PERIOD
+  #endif
+  #if DISABLED(THERMAL_PROTECTION_HYSTERESIS)
+    #error DEPENDENCY ERROR: Missing setting THERMAL_PROTECTION_HYSTERESIS
+  #endif
+  #if DISABLED(WATCH_TEMP_PERIOD)
+    #error DEPENDENCY ERROR: Missing setting WATCH_TEMP_PERIOD
+  #endif
+  #if DISABLED(WATCH_TEMP_INCREASE)
+    #error DEPENDENCY ERROR: Missing setting WATCH_TEMP_INCREASE
+  #endif
+#endif
+#if ENABLED(THERMAL_PROTECTION_BED)
+  #if DISABLED(THERMAL_PROTECTION_BED_PERIOD)
+    #error DEPENDENCY ERROR: Missing setting THERMAL_PROTECTION_BED_PERIOD
+  #endif
+  #if DISABLED(THERMAL_PROTECTION_BED_HYSTERESIS)
+    #error DEPENDENCY ERROR: Missing setting THERMAL_PROTECTION_BED_HYSTERESIS
+  #endif
+#endif
+//fan
+#if DISABLED(SOFT_PWM_SCALE)
+  #error DEPENDENCY ERROR: Missing setting SOFT_PWM_SCALE
+#endif
+
+#if ENABLED(CONTROLLERFAN)
+  #if DISABLED(CONTROLLERFAN_SECS)
+    #error DEPENDENCY ERROR: Missing setting CONTROLLERFAN_SECS
+  #endif
+  #if DISABLED(CONTROLLERFAN_SPEED)
+    #error DEPENDENCY ERROR: Missing setting CONTROLLERFAN_SPEED
+  #endif
+  #if DISABLED(CONTROLLERFAN_MIN_SPEED)
+    #error DEPENDENCY ERROR: Missing setting CONTROLLERFAN_MIN_SPEED
+  #endif
+#endif
+
+#if ENABLED(EXTRUDER_AUTO_FAN)
+  #if DISABLED(EXTRUDER_AUTO_FAN_TEMPERATURE)
+    #error DEPENDENCY ERROR: Missing setting EXTRUDER_AUTO_FAN_TEMPERATURE
+  #endif
+  #if DISABLED(EXTRUDER_AUTO_FAN_SPEED)
+    #error DEPENDENCY ERROR: Missing setting EXTRUDER_AUTO_FAN_SPEED
+  #endif
+  #if DISABLED(EXTRUDER_AUTO_FAN_MIN_SPEED)
+    #error DEPENDENCY ERROR: Missing setting EXTRUDER_AUTO_FAN_MIN_SPEED
+  #endif
+#endif
+
+//extruder
+#if ENABLED(PREVENT_DANGEROUS_EXTRUDE)
+  #if DISABLED(EXTRUDE_MINTEMP)
+    #error DEPENDENCY ERROR: Missing setting EXTRUDE_MINTEMP
+  #endif
+  #if ENABLED(PREVENT_LENGTHY_EXTRUDE)
+    #if DISABLED(EXTRUDE_MAXLENGTH)
+      #error DEPENDENCY ERROR: Missing setting EXTRUDE_MAXLENGTH
+    #endif
+  #endif
+#endif
+
+#if ENABLED(NPR2)
+  #if DISABLED(COLOR_STEP)
+    #error DEPENDENCY ERROR: Missing setting COLOR_STEP
+  #endif
+  #if DISABLED(COLOR_SLOWRATE)
+    #error DEPENDENCY ERROR: Missing setting COLOR_SLOWRATE
+  #endif
+  #if DISABLED(COLOR_HOMERATE)
+    #error DEPENDENCY ERROR: Missing setting COLOR_HOMERATE
+  #endif
+  #if DISABLED(MOTOR_ANGLE)
+    #error DEPENDENCY ERROR: Missing setting MOTOR_ANGLE
+  #endif
+  #if DISABLED(DRIVER_MICROSTEP)
+    #error DEPENDENCY ERROR: Missing setting DRIVER_MICROSTEP
+  #endif
+  #if DISABLED(CARTER_MOLTIPLICATOR)
+    #error DEPENDENCY ERROR: Missing setting CARTER_MOLTIPLICATOR
+  #endif
+#endif
+
+#if ENABLED(IDLE_OOZING_PREVENT)
+  #if DISABLED(IDLE_OOZING_MINTEMP)
+    #error DEPENDENCY ERROR: Missing setting IDLE_OOZING_MINTEMP
+  #endif
+  #if DISABLED(IDLE_OOZING_FEEDRATE)
+    #error DEPENDENCY ERROR: Missing setting IDLE_OOZING_FEEDRATE
+  #endif
+  #if DISABLED(IDLE_OOZING_SECONDS)
+    #error DEPENDENCY ERROR: Missing setting IDLE_OOZING_SECONDS
+  #endif
+  #if DISABLED(IDLE_OOZING_LENGTH)
+    #error DEPENDENCY ERROR: Missing setting IDLE_OOZING_LENGTH
+  #endif
+  #if DISABLED(IDLE_OOZING_RECOVER_LENGTH)
+    #error DEPENDENCY ERROR: Missing setting IDLE_OOZING_RECOVER_LENGTH
+  #endif
+  #if DISABLED(IDLE_OOZING_RECOVER_FEEDRATE)
+    #error DEPENDENCY ERROR: Missing setting IDLE_OOZING_RECOVER_FEEDRATE
+  #endif
+#endif
+
+#if ENABLED(EXTRUDER_RUNOUT_PREVENT)
+  #if DISABLED(EXTRUDER_RUNOUT_MINTEMP)
+    #error DEPENDENCY ERROR: Missing setting EXTRUDER_RUNOUT_MINTEMP
+  #endif
+  #if DISABLED(EXTRUDER_RUNOUT_SECONDS)
+    #error DEPENDENCY ERROR: Missing setting EXTRUDER_RUNOUT_SECONDS
+  #endif
+  #if DISABLED(EXTRUDER_RUNOUT_ESTEPS)
+    #error DEPENDENCY ERROR: Missing setting EXTRUDER_RUNOUT_ESTEPS
+  #endif
+  #if DISABLED(EXTRUDER_RUNOUT_SPEED)
+    #error DEPENDENCY ERROR: Missing setting EXTRUDER_RUNOUT_SPEED
+  #endif
+  #if DISABLED(EXTRUDER_RUNOUT_EXTRUDE)
+    #error DEPENDENCY ERROR: Missing setting EXTRUDER_RUNOUT_EXTRUDE
+  #endif
+#endif
+
+#if ENABLED(EASY_LOAD)
+  #if DISABLED(BOWDEN_LENGTH)
+    #error DEPENDENCY ERROR: Missing setting BOWDEN_LENGTH
+  #endif
+  #if DISABLED(LCD_PURGE_LENGTH)
+    #error DEPENDENCY ERROR: Missing setting LCD_PURGE_LENGTH
+  #endif
+  #if DISABLED(LCD_RETRACT_LENGTH)
+    #error DEPENDENCY ERROR: Missing setting LCD_RETRACT_LENGTH
+  #endif
+  #if DISABLED(LCD_PURGE_FEEDRATE)
+    #error DEPENDENCY ERROR: Missing setting LCD_PURGE_FEEDRATE
+  #endif
+  #if DISABLED(LCD_RETRACT_FEEDRATE)
+    #error DEPENDENCY ERROR: Missing setting LCD_RETRACT_FEEDRATE
+  #endif
+  #if DISABLED(LCD_LOAD_FEEDRATE)
+    #error DEPENDENCY ERROR: Missing setting LCD_LOAD_FEEDRATE
+  #endif
+  #if DISABLED(LCD_UNLOAD_FEEDRATE)
+    #error DEPENDENCY ERROR: Missing setting LCD_UNLOAD_FEEDRATE
+  #endif
+#endif
+
+#if ENABLED(ADVANCE)
+  #if DISABLED(EXTRUDER_ADVANCE_K)
+    #error DEPENDENCY ERROR: Missing setting EXTRUDER_ADVANCE_K
+  #endif
+  #if DISABLED(D_FILAMENT)
+    #error DEPENDENCY ERROR: Missing setting D_FILAMENT
+  #endif
+  #if DISABLED(STEPS_MM_E)
+    #error DEPENDENCY ERROR: Missing setting STEPS_MM_E
+  #endif
+#endif
+
+#if ENABLED(FILAMENTCHANGEENABLE)
+  #if DISABLED(FILAMENTCHANGE_XPOS)
+    #error DEPENDENCY ERROR: Missing setting FILAMENTCHANGE_XPOS
+  #endif
+  #if DISABLED(FILAMENTCHANGE_YPOS)
+    #error DEPENDENCY ERROR: Missing setting FILAMENTCHANGE_YPOS
+  #endif
+  #if DISABLED(FILAMENTCHANGE_ZADD)
+    #error DEPENDENCY ERROR: Missing setting FILAMENTCHANGE_ZADD
+  #endif
+  #if DISABLED(FILAMENTCHANGE_FIRSTRETRACT)
+    #error DEPENDENCY ERROR: Missing setting FILAMENTCHANGE_FIRSTRETRACT
+  #endif
+  #if DISABLED(FILAMENTCHANGE_FINALRETRACT)
+    #error DEPENDENCY ERROR: Missing setting FILAMENTCHANGE_FINALRETRACT
+  #endif
+  #if DISABLED(FILAMENTCHANGE_PRINTEROFF)
+    #error DEPENDENCY ERROR: Missing setting FILAMENTCHANGE_PRINTEROFF
+  #endif
+#endif
+  
+//Motion
+#if DISABLED(SOFTWARE_MIN_ENDSTOPS)
+  #error DEPENDENCY ERROR: Missing setting SOFTWARE_MIN_ENDSTOPS
+#endif
+#if DISABLED(SOFTWARE_MAX_ENDSTOPS)
+  #error DEPENDENCY ERROR: Missing setting SOFTWARE_MAX_ENDSTOPS
+#endif
+#if ENABLED(AUTO_BED_LEVELING_FEATURE)
+  #if ENABLED(AUTO_BED_LEVELING_GRID)
+    #if DISABLED(MIN_PROBE_EDGE)
+      #error DEPENDENCY ERROR: Missing setting MIN_PROBE_EDGE
+    #endif
+    #if DISABLED(AUTO_BED_LEVELING_GRID_POINTS)
+      #error DEPENDENCY ERROR: Missing setting AUTO_BED_LEVELING_GRID_POINTS
+    #endif
+  #else
+    #if DISABLED(ABL_PROBE_PT_1_X)
+      #error DEPENDENCY ERROR: Missing setting ABL_PROBE_PT_1_X
+    #endif
+    #if DISABLED(ABL_PROBE_PT_1_Y)
+      #error DEPENDENCY ERROR: Missing setting ABL_PROBE_PT_1_Y
+    #endif
+    #if DISABLED(ABL_PROBE_PT_2_X)
+      #error DEPENDENCY ERROR: Missing setting ABL_PROBE_PT_2_X
+    #endif
+    #if DISABLED(ABL_PROBE_PT_2_Y)
+      #error DEPENDENCY ERROR: Missing setting ABL_PROBE_PT_2_Y
+    #endif
+    #if DISABLED(ABL_PROBE_PT_3_X)
+      #error DEPENDENCY ERROR: Missing setting ABL_PROBE_PT_3_X
+    #endif
+    #if DISABLED(ABL_PROBE_PT_3_Y)
+      #error DEPENDENCY ERROR: Missing setting ABL_PROBE_PT_3_Y
+    #endif
+  #endif
+  #if DISABLED(X_PROBE_OFFSET_FROM_EXTRUDER)
+    #error DEPENDENCY ERROR: Missing setting X_PROBE_OFFSET_FROM_EXTRUDER
+  #endif
+  #if DISABLED(Y_PROBE_OFFSET_FROM_EXTRUDER)
+    #error DEPENDENCY ERROR: Missing setting Y_PROBE_OFFSET_FROM_EXTRUDER
+  #endif
+  #if DISABLED(Z_PROBE_OFFSET_FROM_EXTRUDER)
+    #error DEPENDENCY ERROR: Missing setting Z_PROBE_OFFSET_FROM_EXTRUDER
+  #endif
+  #if DISABLED(Z_RAISE_BEFORE_HOMING)
+    #error DEPENDENCY ERROR: Missing setting Z_RAISE_BEFORE_HOMING
+  #endif
+  #if DISABLED(Z_RAISE_BEFORE_PROBING)
+    #error DEPENDENCY ERROR: Missing setting Z_RAISE_BEFORE_PROBING
+  #endif
+  #if DISABLED(Z_RAISE_BETWEEN_PROBINGS)
+    #error DEPENDENCY ERROR: Missing setting Z_RAISE_BETWEEN_PROBINGS
+  #endif
+  #if DISABLED(Z_RAISE_AFTER_PROBING)
+    #error DEPENDENCY ERROR: Missing setting Z_RAISE_AFTER_PROBING
+  #endif
+  #if ENABLED(Z_PROBE_SLED)
+    #if DISABLED(SLED_DOCKING_OFFSET)
+      #error DEPENDENCY ERROR: Missing setting SLED_DOCKING_OFFSET
+    #endif
+  #endif
+  #if ENABLED(Z_SAFE_HOMING)
+    #if DISABLED(Z_SAFE_HOMING_X_POINT)
+      #error DEPENDENCY ERROR: Missing setting Z_SAFE_HOMING_X_POINT
+    #endif
+    #if DISABLED(Z_SAFE_HOMING_Y_POINT)
+      #error DEPENDENCY ERROR: Missing setting Z_SAFE_HOMING_Y_POINT
+    #endif
+  #endif
+#endif
+
+#if DISABLED(NUM_SERVOS)
+  #error DEPENDENCY ERROR: Missing setting NUM_SERVOS 0
+#endif
+#if NUM_SERVOS > 0
+  #if DISABLED(X_ENDSTOP_SERVO_NR)
+    #error DEPENDENCY ERROR: Missing setting X_ENDSTOP_SERVO_NR
+  #endif
+  #if DISABLED(Y_ENDSTOP_SERVO_NR)
+    #error DEPENDENCY ERROR: Missing setting Y_ENDSTOP_SERVO_NR
+  #endif
+  #if DISABLED(Z_ENDSTOP_SERVO_NR)
+    #error DEPENDENCY ERROR: Missing setting Z_ENDSTOP_SERVO_NR
+  #endif
+  #if DISABLED(X_ENDSTOP_SERVO_ANGLES)
+    #error DEPENDENCY ERROR: Missing setting X_ENDSTOP_SERVO_ANGLES
+  #endif
+  #if DISABLED(Y_ENDSTOP_SERVO_ANGLES)
+    #error DEPENDENCY ERROR: Missing setting Y_ENDSTOP_SERVO_ANGLES
+  #endif
+  #if DISABLED(Z_ENDSTOP_SERVO_ANGLES)
+    #error DEPENDENCY ERROR: Missing setting Z_ENDSTOP_SERVO_ANGLES
+  #endif
+  #if DISABLED(SERVO_DEACTIVATION_DELAY)
+    #error DEPENDENCY ERROR: Missing setting SERVO_DEACTIVATION_DELAY
+  #endif
+#endif
+#if ENABLED(BABYSTEPPING)
+  #if DISABLED(BABYSTEP_INVERT_Z)
+    #error DEPENDENCY ERROR: Missing setting BABYSTEP_INVERT_Z
+  #endif
+  #if DISABLED(BABYSTEP_Z_MULTIPLICATOR)
+    #error DEPENDENCY ERROR: Missing setting BABYSTEP_Z_MULTIPLICATOR
+  #endif
+#endif
+#if ENABLED(FWRETRACT)
+  #if DISABLED(MIN_RETRACT)
+    #error DEPENDENCY ERROR: Missing setting MIN_RETRACT
+  #endif
+  #if DISABLED(RETRACT_LENGTH)
+    #error DEPENDENCY ERROR: Missing setting RETRACT_LENGTH
+  #endif
+  #if DISABLED(RETRACT_LENGTH_SWAP)
+    #error DEPENDENCY ERROR: Missing setting RETRACT_LENGTH_SWAP
+  #endif
+  #if DISABLED(RETRACT_FEEDRATE)
+    #error DEPENDENCY ERROR: Missing setting RETRACT_FEEDRATE
+  #endif
+  #if DISABLED(RETRACT_ZLIFT)
+    #error DEPENDENCY ERROR: Missing setting RETRACT_ZLIFT
+  #endif
+  #if DISABLED(RETRACT_RECOVER_LENGTH)
+    #error DEPENDENCY ERROR: Missing setting RETRACT_RECOVER_LENGTH
+  #endif
+  #if DISABLED(RETRACT_RECOVER_LENGTH_SWAP)
+    #error DEPENDENCY ERROR: Missing setting RETRACT_RECOVER_LENGTH_SWAP
+  #endif
+  #if DISABLED(RETRACT_RECOVER_FEEDRATE)
+    #error DEPENDENCY ERROR: Missing setting RETRACT_RECOVER_FEEDRATE
+  #endif
+#endif
+#if ENABLED(DUAL_X_CARRIAGE)
+  #if DISABLED(X2_MIN_POS)
+    #error DEPENDENCY ERROR: Missing setting X2_MIN_POS
+  #endif
+  #if DISABLED(X2_MAX_POS)
+    #error DEPENDENCY ERROR: Missing setting X2_MAX_POS
+  #endif
+  #if DISABLED(X2_HOME_DIR)
+    #error DEPENDENCY ERROR: Missing setting X2_HOME_DIR
+  #endif
+  #if DISABLED(X2_HOME_POS)
+    #error DEPENDENCY ERROR: Missing setting X2_HOME_POS
+  #endif
+  #if DISABLED(DEFAULT_DUAL_X_CARRIAGE_MODE)
+    #error DEPENDENCY ERROR: Missing setting DEFAULT_DUAL_X_CARRIAGE_MODE
+  #endif
+  #if DISABLED(TOOLCHANGE_PARK_ZLIFT)
+    #error DEPENDENCY ERROR: Missing setting TOOLCHANGE_PARK_ZLIFT
+  #endif
+  #if DISABLED(TOOLCHANGE_UNPARK_ZLIFT)
+    #error DEPENDENCY ERROR: Missing setting TOOLCHANGE_UNPARK_ZLIFT
+  #endif
+  #if DISABLED(DEFAULT_DUPLICATION_X_OFFSET)
+    #error DEPENDENCY ERROR: Missing setting DEFAULT_DUPLICATION_X_OFFSET
+  #endif
+#endif
+#if ENABLED(Y_DUAL_STEPPER_DRIVERS)
+  #if DISABLED(INVERT_Y2_VS_Y_DIR)
+    #error DEPENDENCY ERROR: Missing setting INVERT_Y2_VS_Y_DIR
+  #endif
+#endif
+
+//sensors
+#if ENABLED(FILAMENT_SENSOR)
+  #if DISABLED(FILAMENT_SENSOR_EXTRUDER_NUM)
+    #error DEPENDENCY ERROR: Missing setting FILAMENT_SENSOR_EXTRUDER_NUM
+  #endif
+  #if DISABLED(MEASUREMENT_DELAY_CM)
+    #error DEPENDENCY ERROR: Missing setting MEASUREMENT_DELAY_CM
+  #endif
+  #if DISABLED(DEFAULT_NOMINAL_FILAMENT_DIA)
+    #error DEPENDENCY ERROR: Missing setting DEFAULT_NOMINAL_FILAMENT_DIA 
+  #endif
+  #if DISABLED(MEASURED_UPPER_LIMIT)
+    #error DEPENDENCY ERROR: Missing setting MEASURED_UPPER_LIMIT
+  #endif
+  #if DISABLED(MEASURED_LOWER_LIMIT)
+    #error DEPENDENCY ERROR: Missing setting MEASURED_LOWER_LIMIT
+  #endif
+  #if DISABLED(MAX_MEASUREMENT_DELAY)
+    #error DEPENDENCY ERROR: Missing setting MAX_MEASUREMENT_DELAY
+  #endif
+  #if DISABLED(DEFAULT_MEASURED_FILAMENT_DIA)
+    #error DEPENDENCY ERROR: Missing setting DEFAULT_MEASURED_FILAMENT_DIA
+  #endif
+#endif
+#if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #if DISABLED(FILRUNOUT_PIN_INVERTING)
+    #error DEPENDENCY ERROR: Missing setting FILRUNOUT_PIN_INVERTING
+  #endif
+  #if DISABLED(ENDSTOPPULLUP_FIL_RUNOUT)
+    #error DEPENDENCY ERROR: Missing setting ENDSTOPPULLUP_FIL_RUNOUT
+  #endif
+  #if DISABLED(FILAMENT_RUNOUT_SCRIPT)
+    #error DEPENDENCY ERROR: Missing setting FILAMENT_RUNOUT_SCRIPT 
+  #endif
+#endif
+#if ENABLED(POWER_CONSUMPTION)
+  #if DISABLED(POWER_VOLTAGE)
+    #error DEPENDENCY ERROR: Missing setting POWER_VOLTAGE
+  #endif
+  #if DISABLED(POWER_SENSITIVITY)
+    #error DEPENDENCY ERROR: Missing setting POWER_SENSITIVITY
+  #endif
+  #if DISABLED(POWER_OFFSET)
+    #error DEPENDENCY ERROR: Missing setting POWER_OFFSET 
+  #endif
+  #if DISABLED(POWER_ZERO)
+    #error DEPENDENCY ERROR: Missing setting POWER_ZERO 
+  #endif
+  #if DISABLED(POWER_ERROR)
+    #error DEPENDENCY ERROR: Missing setting POWER_ERROR 
+  #endif
+  #if DISABLED(POWER_EFFICIENCY)
+    #error DEPENDENCY ERROR: Missing setting POWER_EFFICIENCY 
+  #endif
+#endif
+
+//addon
+#if ENABLED(SDSUPPORT)
+  #if DISABLED(SD_FINISHED_STEPPERRELEASE)
+    #error DEPENDENCY ERROR: Missing setting SD_FINISHED_STEPPERRELEASE
+  #endif
+  #if DISABLED(SD_FINISHED_RELEASECOMMAND)
+    #error DEPENDENCY ERROR: Missing setting SD_FINISHED_RELEASECOMMAND
+  #endif
+  #if ENABLED(SD_SETTINGS)
+    #if DISABLED(SD_CFG_SECONDS)
+      #error DEPENDENCY ERROR: Missing setting SD_CFG_SECONDS
+    #endif
+    #if DISABLED(CFG_SD_FILE)
+      #error DEPENDENCY ERROR: Missing setting CFG_SD_FILE
+    #endif
+    #if DISABLED(CFG_SD_MAX_KEY_LEN)
+      #error DEPENDENCY ERROR: Missing setting CFG_SD_MAX_KEY_LEN
+    #endif
+    #if DISABLED(CFG_SD_MAX_VALUE_LEN)
+      #error DEPENDENCY ERROR: Missing setting CFG_SD_MAX_VALUE_LEN
+    #endif
+  #endif
+#endif
+#if DISABLED(DISPLAY_CHARSET_HD44780_JAPAN) && DISABLED(DISPLAY_CHARSET_HD44780_WESTERN) && DISABLED(DISPLAY_CHARSET_HD44780_CYRILLIC)
+  #error DEPENDENCY ERROR: Missing setting DISPLAY_CHARSET_HD44780_JAPAN or DISPLAY_CHARSET_HD44780_WESTERN or DISPLAY_CHARSET_HD44780_CYRILLIC
+#endif
+#if ENABLED(SHOW_BOOTSCREEN)
+  #if DISABLED(STRING_SPLASH_LINE1)
+    #error DEPENDENCY ERROR: Missing setting STRING_SPLASH_LINE1
+  #endif
+  #if DISABLED(SPLASH_SCREEN_DURATION)
+    #error DEPENDENCY ERROR: Missing setting SPLASH_SCREEN_DURATION
+  #endif
+#endif
+#if ENABLED(ENCODER_RATE_MULTIPLIER)
+  #if DISABLED(ENCODER_10X_STEPS_PER_SEC)
+    #error DEPENDENCY ERROR: Missing setting ENCODER_10X_STEPS_PER_SEC
+  #endif
+  #if DISABLED(ENCODER_100X_STEPS_PER_SEC)
+    #error DEPENDENCY ERROR: Missing setting ENCODER_100X_STEPS_PER_SEC
+  #endif
+#endif
+#if MB(ALLIGATOR)
+  #if DISABLED(UI_VOLTAGE_LEVEL)
+    #error DEPENDENCY ERROR: Missing setting UI_VOLTAGE_LEVEL
+  #endif
+#endif
+#if ENABLED(REPRAPWORLD_KEYPAD)
+  #if DISABLED(REPRAPWORLD_KEYPAD_MOVE_STEP)
+    #error DEPENDENCY ERROR: Missing setting REPRAPWORLD_KEYPAD_MOVE_STEP
+  #endif
+#endif
+#if ENABLED(LCD_PROGRESS_BAR)
+  #if DISABLED(PROGRESS_BAR_BAR_TIME)
+    #error DEPENDENCY ERROR: Missing setting PROGRESS_BAR_BAR_TIME
+  #endif
+  #if DISABLED(PROGRESS_BAR_MSG_TIME)
+    #error DEPENDENCY ERROR: Missing setting PROGRESS_BAR_MSG_TIME
+  #endif
+  #if DISABLED(PROGRESS_MSG_EXPIRE)
+    #error DEPENDENCY ERROR: Missing setting PROGRESS_MSG_EXPIRE
+  #endif
+#endif
+#if ENABLED(CHDK)
+  #if DISABLED(CHDK_DELAY)
+    #error DEPENDENCY ERROR: Missing setting CHDK_DELAY
+  #endif
+#endif
+//adv motion
+#if ENABLED(DIGIPOT_I2C)
+  #if DISABLED(DIGIPOT_I2C_NUM_CHANNELS)
+    #error DEPENDENCY ERROR: Missing setting DIGIPOT_I2C_NUM_CHANNELS
+  #endif
+  #if DISABLED(DIGIPOT_I2C_MOTOR_CURRENTS)
+    #error DEPENDENCY ERROR: Missing setting DIGIPOT_I2C_MOTOR_CURRENTS
+  #endif
+#endif
+#if ENABLED(HAVE_TMCDRIVER)
+  #if ENABLED(X_IS_TMC)
+    #if DISABLED(X_MAX_CURRENT)
+      #error DEPENDENCY ERROR: Missing setting X_MAX_CURRENT
+    #endif
+    #if DISABLED(X_SENSE_RESISTOR)
+      #error DEPENDENCY ERROR: Missing setting X_SENSE_RESISTOR
+    #endif
+    #if DISABLED(X_MICROSTEPS)
+      #error DEPENDENCY ERROR: Missing setting X_MICROSTEPS
+    #endif
+  #endif
+  #if ENABLED(X2_IS_TMC)
+    #if DISABLED(X2_MAX_CURRENT)
+      #error DEPENDENCY ERROR: Missing setting X2_MAX_CURRENT
+    #endif
+    #if DISABLED(X2_SENSE_RESISTOR)
+      #error DEPENDENCY ERROR: Missing setting X2_SENSE_RESISTOR
+    #endif
+    #if DISABLED(X2_MICROSTEPS)
+      #error DEPENDENCY ERROR: Missing setting X2_MICROSTEPS
+    #endif
+  #endif
+  #if ENABLED(Y_IS_TMC)
+    #if DISABLED(Y_MAX_CURRENT)
+      #error DEPENDENCY ERROR: Missing setting Y_MAX_CURRENT
+    #endif
+    #if DISABLED(Y_SENSE_RESISTOR)
+      #error DEPENDENCY ERROR: Missing setting Y_SENSE_RESISTOR
+    #endif
+    #if DISABLED(Y_MICROSTEPS)
+      #error DEPENDENCY ERROR: Missing setting Y_MICROSTEPS
+    #endif
+  #endif
+  #if ENABLED(Y2_IS_TMC)
+    #if DISABLED(Y2_MAX_CURRENT)
+      #error DEPENDENCY ERROR: Missing setting Y2_MAX_CURRENT
+    #endif
+    #if DISABLED(Y2_SENSE_RESISTOR)
+      #error DEPENDENCY ERROR: Missing setting Y2_SENSE_RESISTOR
+    #endif
+    #if DISABLED(Y2_MICROSTEPS)
+      #error DEPENDENCY ERROR: Missing setting Y2_MICROSTEPS
+    #endif
+  #endif
+  #if ENABLED(Z_IS_TMC)
+    #if DISABLED(Z_MAX_CURRENT)
+      #error DEPENDENCY ERROR: Missing setting Z_MAX_CURRENT
+    #endif
+    #if DISABLED(Z_SENSE_RESISTOR)
+      #error DEPENDENCY ERROR: Missing setting Z_SENSE_RESISTOR
+    #endif
+    #if DISABLED(Z_MICROSTEPS)
+      #error DEPENDENCY ERROR: Missing setting Z_MICROSTEPS
+    #endif
+  #endif
+  #if ENABLED(Z2_IS_TMC)
+    #if DISABLED(Z2_MAX_CURRENT)
+      #error DEPENDENCY ERROR: Missing setting Z2_MAX_CURRENT
+    #endif
+    #if DISABLED(Z2_SENSE_RESISTOR)
+      #error DEPENDENCY ERROR: Missing setting Z2_SENSE_RESISTOR
+    #endif
+    #if DISABLED(Z2_MICROSTEPS)
+      #error DEPENDENCY ERROR: Missing setting Z2_MICROSTEPS
+    #endif
+  #endif
+  #if ENABLED(E0_IS_TMC)
+    #if DISABLED(E0_MAX_CURRENT)
+      #error DEPENDENCY ERROR: Missing setting E0_MAX_CURRENT
+    #endif
+    #if DISABLED(E0_SENSE_RESISTOR)
+      #error DEPENDENCY ERROR: Missing setting E0_SENSE_RESISTOR
+    #endif
+    #if DISABLED(E0_MICROSTEPS)
+      #error DEPENDENCY ERROR: Missing setting E0_MICROSTEPS
+    #endif
+  #endif
+  #if ENABLED(E1_IS_TMC)
+    #if DISABLED(E1_MAX_CURRENT)
+      #error DEPENDENCY ERROR: Missing setting E1_MAX_CURRENT
+    #endif
+    #if DISABLED(E1_SENSE_RESISTOR)
+      #error DEPENDENCY ERROR: Missing setting E1_SENSE_RESISTOR
+    #endif
+    #if DISABLED(E1_MICROSTEPS)
+      #error DEPENDENCY ERROR: Missing setting E1_MICROSTEPS
+    #endif
+  #endif
+  #if ENABLED(E2_IS_TMC)
+    #if DISABLED(E2_MAX_CURRENT)
+      #error DEPENDENCY ERROR: Missing setting E2_MAX_CURRENT
+    #endif
+    #if DISABLED(E2_SENSE_RESISTOR)
+      #error DEPENDENCY ERROR: Missing setting E2_SENSE_RESISTOR
+    #endif
+    #if DISABLED(E2_MICROSTEPS)
+      #error DEPENDENCY ERROR: Missing setting E2_MICROSTEPS
+    #endif
+  #endif
+  #if ENABLED(E3_IS_TMC)
+    #if DISABLED(E3_MAX_CURRENT)
+      #error DEPENDENCY ERROR: Missing setting E3_MAX_CURRENT
+    #endif
+    #if DISABLED(E3_SENSE_RESISTOR)
+      #error DEPENDENCY ERROR: Missing setting E3_SENSE_RESISTOR
+    #endif
+    #if DISABLED(E3_MICROSTEPS)
+      #error DEPENDENCY ERROR: Missing setting E3_MICROSTEPS
+    #endif
+  #endif
+#endif
+#if ENABLED(HAVE_L6470DRIVER)
+  #if ENABLED(X_IS_L6470)
+    #if DISABLED(X_MICROSTEPS)
+      #error DEPENDENCY ERROR: Missing setting X_MICROSTEPS
+    #endif
+    #if DISABLED(X_K_VAL)
+      #error DEPENDENCY ERROR: Missing setting X_K_VAL
+    #endif
+    #if DISABLED(X_OVERCURRENT)
+      #error DEPENDENCY ERROR: Missing setting X_OVERCURRENT
+    #endif
+    #if DISABLED(X_STALLCURRENT)
+      #error DEPENDENCY ERROR: Missing setting X_STALLCURRENT
+    #endif
+  #endif
+  #if ENABLED(X2_IS_L6470)
+    #if DISABLED(X2_MICROSTEPS)
+      #error DEPENDENCY ERROR: Missing setting X2_MICROSTEPS
+    #endif
+    #if DISABLED(X2_K_VAL)
+      #error DEPENDENCY ERROR: Missing setting X2_K_VAL
+    #endif
+    #if DISABLED(X2_OVERCURRENT)
+      #error DEPENDENCY ERROR: Missing setting X2_OVERCURRENT
+    #endif
+    #if DISABLED(X2_STALLCURRENT)
+      #error DEPENDENCY ERROR: Missing setting X2_STALLCURRENT
+    #endif
+  #endif
+  #if ENABLED(Y_IS_L6470)
+    #if DISABLED(Y_MICROSTEPS)
+      #error DEPENDENCY ERROR: Missing setting Y_MICROSTEPS
+    #endif
+    #if DISABLED(Y_K_VAL)
+      #error DEPENDENCY ERROR: Missing setting Y_K_VAL
+    #endif
+    #if DISABLED(Y_OVERCURRENT)
+      #error DEPENDENCY ERROR: Missing setting Y_OVERCURRENT
+    #endif
+    #if DISABLED(Y_STALLCURRENT)
+      #error DEPENDENCY ERROR: Missing setting Y_STALLCURRENT
+    #endif
+  #endif
+  #if ENABLED(Y2_IS_L6470)
+    #if DISABLED(Y2_MICROSTEPS)
+      #error DEPENDENCY ERROR: Missing setting Y2_MICROSTEPS
+    #endif
+    #if DISABLED(Y2_K_VAL)
+      #error DEPENDENCY ERROR: Missing setting Y2_K_VAL
+    #endif
+    #if DISABLED(Y2_OVERCURRENT)
+      #error DEPENDENCY ERROR: Missing setting Y2_OVERCURRENT
+    #endif
+    #if DISABLED(Y2_STALLCURRENT)
+      #error DEPENDENCY ERROR: Missing setting Y2_STALLCURRENT
+    #endif
+  #endif
+  #if ENABLED(Z_IS_L6470)
+    #if DISABLED(Z_MICROSTEPS)
+      #error DEPENDENCY ERROR: Missing setting Z_MICROSTEPS
+    #endif
+    #if DISABLED(Z_K_VAL)
+      #error DEPENDENCY ERROR: Missing setting Z_K_VAL
+    #endif
+    #if DISABLED(Z_OVERCURRENT)
+      #error DEPENDENCY ERROR: Missing setting Z_OVERCURRENT
+    #endif
+    #if DISABLED(Z_STALLCURRENT)
+      #error DEPENDENCY ERROR: Missing setting Z_STALLCURRENT
+    #endif
+  #endif
+  #if ENABLED(Z2_IS_L6470)
+    #if DISABLED(Z2_MICROSTEPS)
+      #error DEPENDENCY ERROR: Missing setting Z2_MICROSTEPS
+    #endif
+    #if DISABLED(Z2_K_VAL)
+      #error DEPENDENCY ERROR: Missing setting Z2_K_VAL
+    #endif
+    #if DISABLED(Z2_OVERCURRENT)
+      #error DEPENDENCY ERROR: Missing setting Z2_OVERCURRENT
+    #endif
+    #if DISABLED(Z2_STALLCURRENT)
+      #error DEPENDENCY ERROR: Missing setting Z2_STALLCURRENT
+    #endif
+  #endif
+  #if ENABLED(E0_IS_L6470)
+    #if DISABLED(E0_MICROSTEPS)
+      #error DEPENDENCY ERROR: Missing setting E0_MICROSTEPS
+    #endif
+    #if DISABLED(E0_K_VAL)
+      #error DEPENDENCY ERROR: Missing setting E0_K_VAL
+    #endif
+    #if DISABLED(E0_OVERCURRENT)
+      #error DEPENDENCY ERROR: Missing setting E0_OVERCURRENT
+    #endif
+    #if DISABLED(E0_STALLCURRENT)
+      #error DEPENDENCY ERROR: Missing setting E0_STALLCURRENT
+    #endif
+  #endif
+  #if ENABLED(E1_IS_L6470)
+    #if DISABLED(E1_MICROSTEPS)
+      #error DEPENDENCY ERROR: Missing setting E1_MICROSTEPS
+    #endif
+    #if DISABLED(E1_K_VAL)
+      #error DEPENDENCY ERROR: Missing setting E1_K_VAL
+    #endif
+    #if DISABLED(E1_OVERCURRENT)
+      #error DEPENDENCY ERROR: Missing setting E1_OVERCURRENT
+    #endif
+    #if DISABLED(E1_STALLCURRENT)
+      #error DEPENDENCY ERROR: Missing setting E1_STALLCURRENT
+    #endif
+  #endif
+  #if ENABLED(E2_IS_L6470)
+    #if DISABLED(E2_MICROSTEPS)
+      #error DEPENDENCY ERROR: Missing setting E2_MICROSTEPS
+    #endif
+    #if DISABLED(E2_K_VAL)
+      #error DEPENDENCY ERROR: Missing setting E2_K_VAL
+    #endif
+    #if DISABLED(E2_OVERCURRENT)
+      #error DEPENDENCY ERROR: Missing setting E2_OVERCURRENT
+    #endif
+    #if DISABLED(E2_STALLCURRENT)
+      #error DEPENDENCY ERROR: Missing setting E2_STALLCURRENT
+    #endif
+  #endif
+  #if ENABLED(E3_IS_L6470)
+    #if DISABLED(E3_MICROSTEPS)
+      #error DEPENDENCY ERROR: Missing setting E3_MICROSTEPS
+    #endif
+    #if DISABLED(E3_K_VAL)
+      #error DEPENDENCY ERROR: Missing setting E3_K_VAL
+    #endif
+    #if DISABLED(E3_OVERCURRENT)
+      #error DEPENDENCY ERROR: Missing setting E3_OVERCURRENT
+    #endif
+    #if DISABLED(E3_STALLCURRENT)
+      #error DEPENDENCY ERROR: Missing setting E3_STALLCURRENT
+    #endif
+  #endif
+#endif
+//buffer
+#if DISABLED(BLOCK_BUFFER_SIZE)
+  #error DEPENDENCY ERROR: Missing setting BLOCK_BUFFER_SIZE
+#endif
+#if DISABLED(MAX_CMD_SIZE)
+  #error DEPENDENCY ERROR: Missing setting MAX_CMD_SIZE
+#endif
+#if DISABLED(BUFSIZE)
+  #error DEPENDENCY ERROR: Missing setting BUFSIZE
+#endif
+#if DISABLED(NUM_POSITON_SLOTS)
+  #error DEPENDENCY ERROR: Missing setting NUM_POSITON_SLOTS
+#endif
+#if DISABLED(DROP_SEGMENTS)
+  #error DEPENDENCY ERROR: Missing setting DROP_SEGMENTS
+#endif
+#if DISABLED(DROP_SEGMENTS)
+  #error DEPENDENCY ERROR: Missing setting DROP_SEGMENTS
+#endif
+#if DISABLED(DEFAULT_MINSEGMENTTIME)
+  #error DEPENDENCY ERROR: Missing setting DEFAULT_MINSEGMENTTIME
+#endif
+#if DISABLED(MM_PER_ARC_SEGMENT)
+  #error DEPENDENCY ERROR: Missing setting MM_PER_ARC_SEGMENT
+#endif
+#if DISABLED(N_ARC_CORRECTION)
+  #error DEPENDENCY ERROR: Missing setting N_ARC_CORRECTION
+#endif
+
+#endif
\ No newline at end of file

MarlinKimbra/language.h

@@ -66,10 +66,6 @@
   #define BUILD_VERSION "V4; MarlinKimbra for 4 extruder"
 #endif
 
-#if DISABLED(MACHINE_UUID)
-  #define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
-#endif
-
 
 #define STRINGIFY_(n) #n
 #define STRINGIFY(n) STRINGIFY_(n)

MarlinKimbra/pins.h

@@ -2514,7 +2514,6 @@
 #define SDPOWER               -1
 #define SDSS                  77 // PA28
 #define SD_DETECT_PIN         87 // PA29
-#define SD_DETECT_INVERTED  false
 #define LED_PIN               -1
 
 #define ORIG_FAN_PIN          92 // PA5
@@ -2741,11 +2740,6 @@
         #define DOGLCD_CS 29
         #define LCD_CONTRAST 1
       #endif
-      // Uncomment screen orientation
-      #define LCD_SCREEN_ROT_0
-      // #define LCD_SCREEN_ROT_90
-      // #define LCD_SCREEN_ROT_180
-      // #define LCD_SCREEN_ROT_270
     #else // standard Hitachi LCD controller
       #define LCD_PINS_RS        4
       #define LCD_PINS_ENABLE    17
@@ -2782,11 +2776,6 @@
   #define LCD_PIN_BL 28  // backlight LED on PA3
   // GLCD features
   #define LCD_CONTRAST 1
-  // Uncomment screen orientation
-  #define LCD_SCREEN_ROT_0
-  // #define LCD_SCREEN_ROT_90
-  // #define LCD_SCREEN_ROT_180
-  // #define LCD_SCREEN_ROT_270
   //The encoder and click button
   #define BTN_EN1 11
   #define BTN_EN2 10

MarlinKimbra/planner.cpp

@@ -591,7 +591,7 @@ float junction_deviation = 0.1;
   block->step_event_count = max(block->steps[X_AXIS], max(block->steps[Y_AXIS], max(block->steps[Z_AXIS], block->steps[E_AXIS])));
 
   // Bail if this is a zero-length block
-  if (block->step_event_count <= dropsegments) return;
+  if (block->step_event_count <= DROP_SEGMENTS) return;
 
   block->fan_speed = fanSpeed;
   #if ENABLED(BARICUDA)
@@ -769,7 +769,7 @@ float junction_deviation = 0.1;
   #endif
   delta_mm[E_AXIS] = (de / axis_steps_per_unit[E_AXIS + extruder]) * volumetric_multiplier[extruder] * extruder_multiplier[extruder] / 100.0;
 
-  if (block->steps[X_AXIS] <= dropsegments && block->steps[Y_AXIS] <= dropsegments && block->steps[Z_AXIS] <= dropsegments) {
+  if (block->steps[X_AXIS] <= DROP_SEGMENTS && block->steps[Y_AXIS] <= DROP_SEGMENTS && block->steps[Z_AXIS] <= DROP_SEGMENTS) {
     block->millimeters = fabs(delta_mm[E_AXIS]);
   }
   else {

MarlinKimbra/stepper.cpp

@@ -673,7 +673,7 @@ ISR(TIMER1_COMPA_vect) {
         STEP_START(e,E);
       #endif
 
-      #if ENABLED(STEPPER_HIGH_LOW_DELAY)
+      #if ENABLED(STEPPER_HIGH_LOW_DELAY) && STEPPER_HIGH_LOW_DELAY > 0
         delayMicroseconds(STEPPER_HIGH_LOW_DELAY);
       #endif
 

MarlinKimbra/temperature.cpp

@@ -178,10 +178,6 @@ static void updateTemperaturesFromRawValues();
   millis_t watch_heater_next_ms[HOTENDS] = { 0 };
 #endif
 
-#if DISABLED(SOFT_PWM_SCALE)
-  #define SOFT_PWM_SCALE 0
-#endif
-
 #if ENABLED(FILAMENT_SENSOR)
   static int meas_shift_index;  //used to point to a delayed sample in buffer for filament width sensor
 #endif
@@ -751,7 +747,24 @@ static float analog2temp(int raw, uint8_t e) {
 
     return celsius;
   }
-  return ((raw * ((5.0 * 100.0) / 1024.0) / OVERSAMPLENR) * TEMP_SENSOR_AD595_GAIN) + TEMP_SENSOR_AD595_OFFSET;
+  switch(e) {
+    #if TEMP_SENSOR_BED
+      case -1: return ((raw * ((5.0 * 100.0) / 1024.0) / OVERSAMPLENR) * TEMP_SENSOR_AD595_GAIN) + TEMP_SENSOR_AD595_OFFSET;
+    #endif
+    #if HEATER_0_USES_AD595
+      case 0: return ((raw * ((5.0 * 100.0) / 1024.0) / OVERSAMPLENR) * TEMP_SENSOR_AD595_GAIN) + TEMP_SENSOR_AD595_OFFSET;
+    #endif
+    #if HEATER_1_USES_AD595
+      case 1: return ((raw * ((5.0 * 100.0) / 1024.0) / OVERSAMPLENR) * TEMP_SENSOR_AD595_GAIN) + TEMP_SENSOR_AD595_OFFSET;
+    #endif
+    #if HEATER_2_USES_AD595
+      case 2: return ((raw * ((5.0 * 100.0) / 1024.0) / OVERSAMPLENR) * TEMP_SENSOR_AD595_GAIN) + TEMP_SENSOR_AD595_OFFSET;
+    #endif
+    #if HEATER_3_USES_AD595
+      case 3: return ((raw * ((5.0 * 100.0) / 1024.0) / OVERSAMPLENR) * TEMP_SENSOR_AD595_GAIN) + TEMP_SENSOR_AD595_OFFSET;
+    #endif
+  }
+  return (raw * ((5.0 * 100.0) / 1024.0) / OVERSAMPLENR);
 }
 
 // Derived from RepRap FiveD extruder::getTemperature()

MarlinKimbra/thermistortables.h

@@ -1070,7 +1070,7 @@ const short temptable_1047[][2] PROGMEM = {
 
 #if (THERMISTORHEATER_0 == 998) || (THERMISTORHEATER_1 == 998) || (THERMISTORHEATER_2 == 998) || (THERMISTORHEATER_3 == 998) || (THERMISTORBED == 998) //User defined table
   // Dummy Thermistor table.. It will ALWAYS read a fixed value.
-  #if DISABLED(UMMY_THERMISTOR_998_VALUE)
+  #if DISABLED(DUMMY_THERMISTOR_998_VALUE)
     #define DUMMY_THERMISTOR_998_VALUE 25
   #endif
   const short temptable_998[][2] PROGMEM = {

MarlinKimbra/ultralcd.cpp

@@ -929,8 +929,8 @@ static void _lcd_move(const char *name, AxisEnum axis, int min, int max) {
   if (encoderPosition != 0) {
     refresh_cmd_timeout();
     current_position[axis] += float((int)encoderPosition) * move_menu_scale;
-    if (min_software_endstops && current_position[axis] < min) current_position[axis] = min;
-    if (max_software_endstops && current_position[axis] > max) current_position[axis] = max;
+    if (SOFTWARE_MIN_ENDSTOPS && current_position[axis] < min) current_position[axis] = min;
+    if (SOFTWARE_MAX_ENDSTOPS && current_position[axis] > max) current_position[axis] = max;
     encoderPosition = 0;
     line_to_current(manual_feedrate[axis]);
     lcdDrawUpdate = 1;