Fix

MarlinKimbra/Configuration_Cartesian.h

@@ -110,7 +110,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = false;      // set to true to invert the lo
 //    Probe every point in a rectangular grid
 //    You must specify the rectangle, and the density of sample points
 //    This mode is preferred because there are more measurements.
-//    It used to be called ACCURATE_BED_LEVELING but "grid" is more descriptive
+//    It used to be called ACCURATE_BED_COMPENSATION but "grid" is more descriptive
 
 //  - "3-point" mode
 //    Probe 3 arbitrary points on the bed (that aren't colinear)
@@ -161,7 +161,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = false;      // set to true to invert the lo
 #define PROBE_SERVO_DEACTIVATION_DELAY 300
 
 
-//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
+//If you have enabled the Bed Auto Compensation and are using the same Z Probe for Z Homing,
 //it is highly recommended you let this Z_SAFE_HOMING enabled!!!
 
 #define Z_SAFE_HOMING   // This feature is meant to avoid Z homing with probe outside the bed area.

MarlinKimbra/Configuration_Corexy.h

@@ -115,7 +115,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = false;      // set to true to invert the lo
 //    Probe every point in a rectangular grid
 //    You must specify the rectangle, and the density of sample points
 //    This mode is preferred because there are more measurements.
-//    It used to be called ACCURATE_BED_LEVELING but "grid" is more descriptive
+//    It used to be called ACCURATE_BED_COMPENSATION but "grid" is more descriptive
 
 //  - "3-point" mode
 //    Probe 3 arbitrary points on the bed (that aren't colinear)
@@ -166,7 +166,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = false;      // set to true to invert the lo
 #define PROBE_SERVO_DEACTIVATION_DELAY 300
 
 
-//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
+//If you have enabled the Bed Auto Compensation and are using the same Z Probe for Z Homing,
 //it is highly recommended you let this Z_SAFE_HOMING enabled!!!
 
 #define Z_SAFE_HOMING   // This feature is meant to avoid Z homing with probe outside the bed area.

MarlinKimbra/Configuration_Scara.h

@@ -133,7 +133,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 //    Probe every point in a rectangular grid
 //    You must specify the rectangle, and the density of sample points
 //    This mode is preferred because there are more measurements.
-//    It used to be called ACCURATE_BED_LEVELING but "grid" is more descriptive
+//    It used to be called ACCURATE_BED_COMPENSATION but "grid" is more descriptive
 
 //  - "3-point" mode
 //    Probe 3 arbitrary points on the bed (that aren't colinear)
@@ -177,12 +177,12 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 
 //If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
 //The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
-// You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile.
+// You MUST HAVE the SERVO ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile.
 
-//  #define PROBE_SERVO_DEACTIVATION_DELAY 300
+#define PROBE_SERVO_DEACTIVATION_DELAY 300
 
 
-//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
+//If you have enabled the Bed Auto Compensation and are using the same Z Probe for Z Homing,
 //it is highly recommended you let this Z_SAFE_HOMING enabled!!!
 
 #define Z_SAFE_HOMING   // This feature is meant to avoid Z homing with probe outside the bed area.