Merge remote-tracking branch 'refs/remotes/origin/master' into dev

MarlinKimbra/Configuration_Cartesian.h

@@ -253,24 +253,24 @@
 
 // Enable this to sample the bed in a grid (least squares solution)
 // Note: this feature generates 10KB extra code size
-//#define AUTO_BED_LEVELING_GRID
+#define AUTO_BED_LEVELING_GRID
 
 // yes AUTO_BED_LEVELING_GRID
-//#define MIN_PROBE_EDGE 10 // The probe square sides can be no smaller than this
+#define MIN_PROBE_EDGE 10 // The probe square sides can be no smaller than this
 // Set the number of grid points per dimension
 // You probably don't need more than 3 (squared=9)
-//#define AUTO_BED_LEVELING_GRID_POINTS 2
+#define AUTO_BED_LEVELING_GRID_POINTS 2
 // yes AUTO_BED_LEVELING_GRID
 
 // no AUTO_BED_LEVELING_GRID
 // Arbitrary points to probe. A simple cross-product
 // is used to estimate the plane of the bed.
-//#define ABL_PROBE_PT_1_X 15
-//#define ABL_PROBE_PT_1_Y 180
-//#define ABL_PROBE_PT_2_X 15
-//#define ABL_PROBE_PT_2_Y 20
-//#define ABL_PROBE_PT_3_X 170
-//#define ABL_PROBE_PT_3_Y 20
+#define ABL_PROBE_PT_1_X 15
+#define ABL_PROBE_PT_1_Y 180
+#define ABL_PROBE_PT_2_X 15
+#define ABL_PROBE_PT_2_Y 20
+#define ABL_PROBE_PT_3_X 170
+#define ABL_PROBE_PT_3_Y 20
 // no AUTO_BED_LEVELING_GRID
 
 // Offsets to the probe relative to the extruder tip (Hotend - Probe)

MarlinKimbra/Configuration_Feature.h

@@ -134,7 +134,7 @@
  *                                                                     *
  ***********************************************************************/
 //#define TEMP_SENSOR_1_AS_REDUNDANT
-//#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 // (degC)
+#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 // (degC)
 /***********************************************************************/
 
 
@@ -271,21 +271,21 @@
  ********************************************************************************/
 //#define THERMAL_PROTECTION_HOTENDS
 
-//#define THERMAL_PROTECTION_PERIOD    40     // Seconds
-//#define THERMAL_PROTECTION_HYSTERESIS 4     // Degrees Celsius
+#define THERMAL_PROTECTION_PERIOD    40     // Seconds
+#define THERMAL_PROTECTION_HYSTERESIS 4     // Degrees Celsius
 
 // Whenever an M104 or M109 increases the target temperature the firmware will wait for the
 // WATCH TEMP PERIOD to expire, and if the temperature hasn't increased by WATCH TEMP INCREASE
 // degrees, the machine is halted, requiring a hard reset. This test restarts with any M104/M109,
 //but only if the current temperature is far enough below the target for a reliable test.
-//#define WATCH_TEMP_PERIOD  16               // Seconds
-//#define WATCH_TEMP_INCREASE 4               // Degrees Celsius
+#define WATCH_TEMP_PERIOD  16               // Seconds
+#define WATCH_TEMP_INCREASE 4               // Degrees Celsius
   
 
 //#define THERMAL_PROTECTION_BED 
 
-//#define THERMAL_PROTECTION_BED_PERIOD    20 // Seconds
-//#define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
+#define THERMAL_PROTECTION_BED_PERIOD    20 // Seconds
+#define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
 /********************************************************************************/
 
 
@@ -321,9 +321,9 @@
 // and turn off after the set amount of seconds from last driver being disabled again
 // You need to set CONTROLLERFAN_PIN in Configuration_pins.h
 //#define CONTROLLERFAN
-//#define CONTROLLERFAN_SECS 60     // How many seconds, after all motors were disabled, the fan should run
-//#define CONTROLLERFAN_SPEED 255   // 255 = full speed
-//#define CONTROLLERFAN_MIN_SPEED 0
+#define CONTROLLERFAN_SECS       60   // How many seconds, after all motors were disabled, the fan should run
+#define CONTROLLERFAN_SPEED     255   // 255 = full speed
+#define CONTROLLERFAN_MIN_SPEED   0
 
 // Extruder cooling fans
 // Configure fan pin outputs to automatically turn on/off when the associated
@@ -332,9 +332,9 @@
 // the fan will turn on when any selected extruder is above the threshold.
 // You need to set _AUTO_FAN_PIN in Configuration_pins.h
 //#define EXTRUDER_AUTO_FAN
-//#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
-//#define EXTRUDER_AUTO_FAN_SPEED 255  // 255 = full speed
-//#define EXTRUDER_AUTO_FAN_MIN_SPEED 0
+#define EXTRUDER_AUTO_FAN_TEMPERATURE  50
+#define EXTRUDER_AUTO_FAN_SPEED       255  // 255 = full speed
+#define EXTRUDER_AUTO_FAN_MIN_SPEED     0
 /**************************************************************************/
 
 
@@ -381,7 +381,7 @@
 
 // if PREVENT DANGEROUS EXTRUDE is on, you can still disable (uncomment) very long bits of extrusion separately.
 //#define PREVENT_LENGTHY_EXTRUDE
-//#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH + Y_MAX_LENGTH) // prevent extrusion of very large distances.
+#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH + Y_MAX_LENGTH) // prevent extrusion of very large distances.
 /***********************************************************************/
 
 
@@ -436,12 +436,12 @@
  *                                                                     *
  ***********************************************************************/
 //#define NPR2
-//#define COLOR_STEP {0, 10, 20, 30}   // CARTER ANGLE
-//#define COLOR_SLOWRATE 170           // MICROSECOND delay for carter motor routine (Carter Motor Feedrate: upper value-slow feedrate)  
-//#define COLOR_HOMERATE 4             // FEEDRATE for carter home
-//#define MOTOR_ANGLE 1.8              // Nema angle for single step 
-//#define DRIVER_MICROSTEP 4           // Microstep moltiplicator driver (set jumper MS1-2-3) off-on-off 1/4 microstepping.
-//#define CARTER_MOLTIPLICATOR 14.22   // CARTER MOLTIPLICATOR (gear ratio 13/31-10/31)
+#define COLOR_STEP {0, 10, 20, 30}   // CARTER ANGLE
+#define COLOR_SLOWRATE 170           // MICROSECOND delay for carter motor routine (Carter Motor Feedrate: upper value-slow feedrate)  
+#define COLOR_HOMERATE 4             // FEEDRATE for carter home
+#define MOTOR_ANGLE 1.8              // Nema angle for single step 
+#define DRIVER_MICROSTEP 4           // Microstep moltiplicator driver (set jumper MS1-2-3) off-on-off 1/4 microstepping.
+#define CARTER_MOLTIPLICATOR 14.22   // CARTER MOLTIPLICATOR (gear ratio 13/31-10/31)
 /***********************************************************************/
 
 
@@ -459,10 +459,10 @@
  *                                                                     *
  ***********************************************************************/
 //#define DONDOLO
-//#define DONDOLO_SERVO_INDEX 0
-//#define DONDOLO_SERVOPOS_E0 120
-//#define DONDOLO_SERVOPOS_E1 10
-//#define DONDOLO_SERVO_DELAY 1000
+#define DONDOLO_SERVO_INDEX 0
+#define DONDOLO_SERVOPOS_E0 120
+#define DONDOLO_SERVOPOS_E1 10
+#define DONDOLO_SERVO_DELAY 1000
 /***********************************************************************/
 
 
@@ -487,12 +487,12 @@
  *                                                                     *
  ***********************************************************************/
 //#define IDLE_OOZING_PREVENT
-//#define IDLE_OOZING_MINTEMP           190
-//#define IDLE_OOZING_FEEDRATE          50    //default feedrate for retracting (mm/s)
-//#define IDLE_OOZING_SECONDS           5
-//#define IDLE_OOZING_LENGTH            15    //default retract length (positive mm)
-//#define IDLE_OOZING_RECOVER_LENGTH    0     //default additional recover length (mm, added to retract length when recovering)
-//#define IDLE_OOZING_RECOVER_FEEDRATE  50    //default feedrate for recovering from retraction (mm/s)
+#define IDLE_OOZING_MINTEMP           190
+#define IDLE_OOZING_FEEDRATE          50    //default feedrate for retracting (mm/s)
+#define IDLE_OOZING_SECONDS           5
+#define IDLE_OOZING_LENGTH            15    //default retract length (positive mm)
+#define IDLE_OOZING_RECOVER_LENGTH    0     //default additional recover length (mm, added to retract length when recovering)
+#define IDLE_OOZING_RECOVER_FEEDRATE  50    //default feedrate for recovering from retraction (mm/s)
 /***********************************************************************/
 
 
@@ -507,11 +507,11 @@
  *                                                                                       *
  *****************************************************************************************/
 //#define EXTRUDER_RUNOUT_PREVENT
-//#define EXTRUDER_RUNOUT_MINTEMP 190
-//#define EXTRUDER_RUNOUT_SECONDS  30
-//#define EXTRUDER_RUNOUT_ESTEPS   14  //mm filament
-//#define EXTRUDER_RUNOUT_SPEED  1500  //extrusion speed
-//#define EXTRUDER_RUNOUT_EXTRUDE 100
+#define EXTRUDER_RUNOUT_MINTEMP 190
+#define EXTRUDER_RUNOUT_SECONDS  30
+#define EXTRUDER_RUNOUT_ESTEPS   14  //mm filament
+#define EXTRUDER_RUNOUT_SPEED  1500  //extrusion speed
+#define EXTRUDER_RUNOUT_EXTRUDE 100
 /*****************************************************************************************/
 
 
@@ -523,13 +523,13 @@
  *                                                                     *
  ***********************************************************************/
 //#define EASY_LOAD
-//#define BOWDEN_LENGTH 250       // mm
-//#define LCD_PURGE_LENGTH 3      // mm
-//#define LCD_RETRACT_LENGTH 3    // mm
-//#define LCD_PURGE_FEEDRATE 3    // mm/s
-//#define LCD_RETRACT_FEEDRATE 10 // mm/s
-//#define LCD_LOAD_FEEDRATE 8     // mm/s
-//#define LCD_UNLOAD_FEEDRATE 8   // mm/s
+#define BOWDEN_LENGTH 250       // mm
+#define LCD_PURGE_LENGTH 3      // mm
+#define LCD_RETRACT_LENGTH 3    // mm
+#define LCD_PURGE_FEEDRATE 3    // mm/s
+#define LCD_RETRACT_FEEDRATE 10 // mm/s
+#define LCD_LOAD_FEEDRATE 8     // mm/s
+#define LCD_UNLOAD_FEEDRATE 8   // mm/s
 /***********************************************************************/
 
 
@@ -549,9 +549,9 @@
  *                                                                                       *
  *****************************************************************************************/
 //#define ADVANCE
-//#define EXTRUDER_ADVANCE_K .0
-//#define D_FILAMENT 2.85
-//#define STEPS_MM_E 836
+#define EXTRUDER_ADVANCE_K .0
+#define D_FILAMENT 2.85
+#define STEPS_MM_E 836
 /*****************************************************************************************/
 
 
@@ -566,12 +566,12 @@
  *                                                                        *
  **************************************************************************/
 //#define FILAMENTCHANGEENABLE
-//#define FILAMENTCHANGE_XPOS 3
-//#define FILAMENTCHANGE_YPOS 3
-//#define FILAMENTCHANGE_ZADD 10
-//#define FILAMENTCHANGE_FIRSTRETRACT -2
-//#define FILAMENTCHANGE_FINALRETRACT -100
-//#define FILAMENTCHANGE_PRINTEROFF 5     // Minutes
+#define FILAMENTCHANGE_XPOS 3
+#define FILAMENTCHANGE_YPOS 3
+#define FILAMENTCHANGE_ZADD 10
+#define FILAMENTCHANGE_FIRSTRETRACT -2
+#define FILAMENTCHANGE_FINALRETRACT -100
+#define FILAMENTCHANGE_PRINTEROFF 5     // Minutes
 /**************************************************************************/
 
 
@@ -602,19 +602,19 @@
 // If you select a configuration below, this will receive a default value and does not need to be set manually
 // set it manually if you have more servos than extruders and wish to manually control some
 // leaving it defining as 0 will disable the servo subsystem
-//#define NUM_SERVOS 0
+#define NUM_SERVOS 0
 // Servo index starts with 0 for M280 command
 
 // Servo Endstops
 // This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes.
 // Use M666 H to set the z-probe vertical offset from the nozzle. Store that setting with M500.
 // Define nr servo for endstop -1 not define. Servo index start 0
-//#define X_ENDSTOP_SERVO_NR -1
-//#define Y_ENDSTOP_SERVO_NR -1
-//#define Z_ENDSTOP_SERVO_NR -1
-//#define X_ENDSTOP_SERVO_ANGLES {0,0}  // X Axis Extend and Retract angles
-//#define Y_ENDSTOP_SERVO_ANGLES {0,0}  // Y Axis Extend and Retract angles
-//#define Z_ENDSTOP_SERVO_ANGLES {90,0} // Z Axis Extend and Retract angles
+#define X_ENDSTOP_SERVO_NR -1
+#define Y_ENDSTOP_SERVO_NR -1
+#define Z_ENDSTOP_SERVO_NR -1
+#define X_ENDSTOP_SERVO_ANGLES {0,0}  // X Axis Extend and Retract angles
+#define Y_ENDSTOP_SERVO_ANGLES {0,0}  // Y Axis Extend and Retract angles
+#define Z_ENDSTOP_SERVO_ANGLES {90,0} // Z Axis Extend and Retract angles
 
 // Servo deactivation
 //
@@ -624,7 +624,7 @@
 // Delay (in microseconds) before turning the servo off. This depends on the servo speed.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
-//#define SERVO_DEACTIVATION_DELAY 300
+#define SERVO_DEACTIVATION_DELAY 300
 /***********************************************************************/
 
 
@@ -704,10 +704,10 @@
  *                                                                        *
  **************************************************************************/
 //#define BABYSTEPPING
-//#define BABYSTEP_XY  // not only z, but also XY in the menu. more clutter, more functions
+#define BABYSTEP_XY  // not only z, but also XY in the menu. more clutter, more functions
                      // not implemented for CoreXY and deltabots!
-//#define BABYSTEP_INVERT_Z false   // true for inverse movements in Z
-//#define BABYSTEP_MULTIPLICATOR 2  // faster z movements
+#define BABYSTEP_INVERT_Z false   // true for inverse movements in Z
+#define BABYSTEP_MULTIPLICATOR 2  // faster z movements
 /**************************************************************************/
 
 
@@ -725,15 +725,15 @@
  * Uncomment FWRETRACT to enable this feature                             *
  *                                                                        *
  **************************************************************************/
-//#define FWRETRACT                       //ONLY PARTIALLY TESTED
-//#define MIN_RETRACT                 0.1 //minimum extruded mm to accept a automatic gcode retraction attempt
-//#define RETRACT_LENGTH              3   //default retract length (positive mm)
-//#define RETRACT_LENGTH_SWAP        13   //default swap retract length (positive mm), for extruder change
-//#define RETRACT_FEEDRATE           45   //default feedrate for retracting (mm/s)
-//#define RETRACT_ZLIFT               0   //default retract Z-lift
-//#define RETRACT_RECOVER_LENGTH      0   //default additional recover length (mm, added to retract length when recovering)
-//#define RETRACT_RECOVER_LENGTH_SWAP 0   //default additional swap recover length (mm, added to retract length when recovering from extruder change)
-//#define RETRACT_RECOVER_FEEDRATE    8   //default feedrate for recovering from retraction (mm/s)
+//#define FWRETRACT                     //ONLY PARTIALLY TESTED
+#define MIN_RETRACT                 0.1 //minimum extruded mm to accept a automatic gcode retraction attempt
+#define RETRACT_LENGTH              3   //default retract length (positive mm)
+#define RETRACT_LENGTH_SWAP        13   //default swap retract length (positive mm), for extruder change
+#define RETRACT_FEEDRATE           45   //default feedrate for retracting (mm/s)
+#define RETRACT_ZLIFT               0   //default retract Z-lift
+#define RETRACT_RECOVER_LENGTH      0   //default additional recover length (mm, added to retract length when recovering)
+#define RETRACT_RECOVER_LENGTH_SWAP 0   //default additional swap recover length (mm, added to retract length when recovering from extruder change)
+#define RETRACT_RECOVER_FEEDRATE    8   //default feedrate for recovering from retraction (mm/s)
 /**************************************************************************/
 
 
@@ -752,10 +752,10 @@
 // Configuration for second X-carriage
 // Note: the first x-carriage is defined as the x-carriage which homes to the minimum endstop;
 // the second x-carriage always homes to the maximum endstop.
-//#define X2_MIN_POS 80     // set minimum to ensure second x-carriage doesn't hit the parked first X-carriage
-//#define X2_MAX_POS 353    // set maximum to the distance between toolheads when both heads are homed
-//#define X2_HOME_DIR 1     // the second X-carriage always homes to the maximum endstop position
-//#define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position
+#define X2_MIN_POS 80     // set minimum to ensure second x-carriage doesn't hit the parked first X-carriage
+#define X2_MAX_POS 353    // set maximum to the distance between toolheads when both heads are homed
+#define X2_HOME_DIR 1     // the second X-carriage always homes to the maximum endstop position
+#define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position
 // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software
 // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops
 // without modifying the firmware (through the "M218 T1 X???" command).
@@ -771,14 +771,14 @@
 //                           once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm])
 
 // This is the default power-up mode which can be later using M605.
-//#define DEFAULT_DUAL_X_CARRIAGE_MODE 0
+#define DEFAULT_DUAL_X_CARRIAGE_MODE 0
 
 // Default settings in "Auto-park Mode"
-//#define TOOLCHANGE_PARK_ZLIFT   0.2      // the distance to raise Z axis when parking an extruder
-//#define TOOLCHANGE_UNPARK_ZLIFT 1        // the distance to raise Z axis when unparking an extruder
+#define TOOLCHANGE_PARK_ZLIFT   0.2      // the distance to raise Z axis when parking an extruder
+#define TOOLCHANGE_UNPARK_ZLIFT 1        // the distance to raise Z axis when unparking an extruder
 
 // Default x offset in duplication mode (typically set to half print bed width)
-//#define DEFAULT_DUPLICATION_X_OFFSET 100
+#define DEFAULT_DUPLICATION_X_OFFSET 100
 /*****************************************************************************************/
 
 
@@ -801,7 +801,7 @@
 //#define Y_DUAL_STEPPER_DRIVERS
 
 // Define if the two Y drives need to rotate in opposite directions
-//#define INVERT_Y2_VS_Y_DIR false
+#define INVERT_Y2_VS_Y_DIR false
 /*****************************************************************************************/
 
 
@@ -879,14 +879,14 @@
  *                                                                                *
  **********************************************************************************/
 //#define FILAMENT_SENSOR
-//#define FILAMENT_SENSOR_EXTRUDER_NUM  0     //The number of the extruder that has the filament sensor (0,1,2,3)
-//#define MEASUREMENT_DELAY_CM         14     //measurement delay in cm.  This is the distance from filament sensor to middle of barrel
-//#define MEASURED_UPPER_LIMIT          2.00  //upper limit factor used for sensor reading validation in mm
-//#define MEASURED_LOWER_LIMIT          1.35  //lower limit factor for sensor reading validation in mm
-//#define MAX_MEASUREMENT_DELAY        20     //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM  and lower number saves RAM)
+#define FILAMENT_SENSOR_EXTRUDER_NUM  0     //The number of the extruder that has the filament sensor (0,1,2,3)
+#define MEASUREMENT_DELAY_CM         14     //measurement delay in cm.  This is the distance from filament sensor to middle of barrel
+#define MEASURED_UPPER_LIMIT          2.00  //upper limit factor used for sensor reading validation in mm
+#define MEASURED_LOWER_LIMIT          1.35  //lower limit factor for sensor reading validation in mm
+#define MAX_MEASUREMENT_DELAY        20     //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM  and lower number saves RAM)
 
 //defines used in the code
-//#define DEFAULT_MEASURED_FILAMENT_DIA  DEFAULT_NOMINAL_FILAMENT_DIA  //set measured to nominal initially
+#define DEFAULT_MEASURED_FILAMENT_DIA  DEFAULT_NOMINAL_FILAMENT_DIA  //set measured to nominal initially
 
 //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status.  Status will appear for 5 sec.
 //#define FILAMENT_LCD_DISPLAY
@@ -908,9 +908,9 @@
  *                                                                                *
  **********************************************************************************/
 //#define FILAMENT_RUNOUT_SENSOR
-//#define FILRUNOUT_PIN_INVERTING true        // Should be uncommented and true or false should assigned
-//#define ENDSTOPPULLUP_FIL_RUNOUT            // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
-//#define FILAMENT_RUNOUT_SCRIPT "M600"       // Script execute when filament run out
+#define FILRUNOUT_PIN_INVERTING true        // Should be uncommented and true or false should assigned
+#define ENDSTOPPULLUP_FIL_RUNOUT            // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
+#define FILAMENT_RUNOUT_SCRIPT "M600"       // Script execute when filament run out
 /**********************************************************************************/
 
 
@@ -963,12 +963,12 @@
  *                                                                        *
  **************************************************************************/
 //#define POWER_CONSUMPTION
-//#define POWER_VOLTAGE      12.00    //(V) The power supply OUT voltage
-//#define POWER_SENSITIVITY   0.066   //(V/A) How much increase V for 1A of increase
-//#define POWER_OFFSET        0.005   //(A) Help to get 0A when no load is connected.
-//#define POWER_ZERO          2.500   //(V) The /\V coming out from the sensor when no current flow.
-//#define POWER_ERROR         0.0     //(%) Ammortize measure error.
-//#define POWER_EFFICIENCY  100.0     //(%) The power efficency of the power supply
+#define POWER_VOLTAGE      12.00    //(V) The power supply OUT voltage
+#define POWER_SENSITIVITY   0.066   //(V/A) How much increase V for 1A of increase
+#define POWER_OFFSET        0.005   //(A) Help to get 0A when no load is connected.
+#define POWER_ZERO          2.500   //(V) The /\V coming out from the sensor when no current flow.
+#define POWER_ERROR         0.0     //(%) Ammortize measure error.
+#define POWER_EFFICIENCY  100.0     //(%) The power efficency of the power supply
 
 //When using an LCD, uncomment the line below to display the Power consumption sensor data on the last line instead of status. Status will appear for 5 sec.
 //#define POWER_CONSUMPTION_LCD_DISPLAY
@@ -1034,10 +1034,10 @@
 
 //This enable the firmware to write some configuration that require frequent update, on the SD card
 //#define SD_SETTINGS                     //Uncomment to enable
-//#define SD_CFG_SECONDS        300         //seconds between update
-//#define CFG_SD_FILE           "INFO.CFG"  //name of the configuration file
-//#define CFG_SD_MAX_KEY_LEN    3+1         //icrease this if you add key name longer than the actual value.
-//#define CFG_SD_MAX_VALUE_LEN  12+1        //this should be enought for int, long and float if you need to retrive strings increase this carefully
+#define SD_CFG_SECONDS        300         //seconds between update
+#define CFG_SD_FILE           "INFO.CFG"  //name of the configuration file
+#define CFG_SD_MAX_KEY_LEN    3+1         //icrease this if you add key name longer than the actual value.
+#define CFG_SD_MAX_VALUE_LEN  12+1        //this should be enought for int, long and float if you need to retrive strings increase this carefully
 /*****************************************************************************************/
 
 
@@ -1176,9 +1176,9 @@
 
 // Show a progress bar on HD44780 LCDs for SD printing
 //#define LCD_PROGRESS_BAR
-//#define PROGRESS_BAR_BAR_TIME 5000 // Amount of time (ms) to show the bar
-//#define PROGRESS_BAR_MSG_TIME 1500 // Amount of time (ms) to show the status message
-//#define PROGRESS_MSG_EXPIRE   0    // Amount of time (ms) to retain the status message (0=forever)
+#define PROGRESS_BAR_BAR_TIME 5000 // Amount of time (ms) to show the bar
+#define PROGRESS_BAR_MSG_TIME 1500 // Amount of time (ms) to show the status message
+#define PROGRESS_MSG_EXPIRE   0    // Amount of time (ms) to retain the status message (0=forever)
 //#define PROGRESS_MSG_ONCE        // Uncomment this to show messages for MSG_TIME then hide them
 /************************************************************************************************/
 
@@ -1209,7 +1209,7 @@
  *                                                                        *
  **************************************************************************/
 //#define CHDK
-//#define CHDK_DELAY 50   //How long in ms the pin should stay HIGH before going LOW again
+#define CHDK_DELAY 50   //How long in ms the pin should stay HIGH before going LOW again
 /**************************************************************************/
 
 
@@ -1263,7 +1263,7 @@
  *                                                                     *
  ***********************************************************************/
 //#define USE_MICROSTEPS
-//#define MICROSTEP_MODES {16, 16, 16, 16} // X Y Z E - [1,2,4,8,16,32]
+#define MICROSTEP_MODES {16, 16, 16, 16} // X Y Z E - [1,2,4,8,16,32]
 /***********************************************************************/
 
 
@@ -1277,7 +1277,7 @@
  *                                                                     *
  ***********************************************************************/
 //#define STEPPER_HIGH_LOW
-//#define STEPPER_HIGH_LOW_DELAY 1u  // Delay in microseconds
+#define STEPPER_HIGH_LOW_DELAY 1u  // Delay in microseconds
 /***********************************************************************/
 
 
@@ -1302,9 +1302,9 @@
  ***********************************************************************/
 //#define DIGIPOT_I2C
 // Number of channels available for I2C digipot, For Azteeg X3 Pro we have 8
-//#define DIGIPOT_I2C_NUM_CHANNELS 8
+#define DIGIPOT_I2C_NUM_CHANNELS 8
 // actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS
-//#define DIGIPOT_I2C_MOTOR_CURRENTS {1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0}
+#define DIGIPOT_I2C_MOTOR_CURRENTS {1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0}
 /***********************************************************************/
 
 
@@ -1484,9 +1484,9 @@
 #define MM_PER_ARC_SEGMENT 1
 #define N_ARC_CORRECTION 25
 
-//#define M100_FREE_MEMORY_WATCHER      // Uncomment to add the M100 Free Memory Watcher for debug purpose
-//#define M100_FREE_MEMORY_DUMPER       // Comment out to remove Dump sub-command
-//#define M100_FREE_MEMORY_CORRUPTOR    // Comment out to remove Corrupt sub-command
+//#define M100_FREE_MEMORY_WATCHER    // Uncomment to add the M100 Free Memory Watcher for debug purpose
+#define M100_FREE_MEMORY_DUMPER       // Comment out to remove Dump sub-command
+#define M100_FREE_MEMORY_CORRUPTOR    // Comment out to remove Corrupt sub-command
 /****************************************************************************************/
 
 
@@ -1517,10 +1517,10 @@
  *                                                                                       *
  *****************************************************************************************/
 //#define START_GCODE
-//#define START_PRINTING_SCRIPT "G28\nG1 Z10 F8000"
+#define START_PRINTING_SCRIPT "G28\nG1 Z10 F8000"
 
 //#define STOP_GCODE
-//#define STOP_PRINTING_SCRIPT "G28\nM107\nM104 T0 S0\nM140 S0\nM84\nM81"
+#define STOP_PRINTING_SCRIPT "G28\nM107\nM104 T0 S0\nM140 S0\nM84\nM81"
 /*****************************************************************************************/
  
 #endif