Skip to content

L
laser-gcode-exporter-inkscape-plugin
Commit 19c67c85 authored by leonmuller's avatar leonmuller
Browse files
Options

Spent a day stuffing around with the exporter and marlin firmware to figure... 

Spent a day stuffing around with the exporter and marlin firmware to figure out why pronterface was throwing checksum errors when
sending lots of G02 and G03 arc vector cuts. It turns out that with too much precision in the cuts marlin's buffer fills up and it's
unable to receive any more serial data. I resolved this by reducing the float point precision down to 3 decimal places and shifting
power and pulse settings to the G00 move command that comes before a set of G01, G02 and G03 commands to limit data that's needed to
be sent over the wire.

I also fixed up the part of the exporter to allow the offset and scaling functions to work. Though I found that looking at the scaling
code it will only scale from the original 0,0 coordinate, it doesn't scale based on a centre point.

I was able to burn vector gcode files with 10000 lines without issue, 30 minute burns with no checksum errors reported by Marlin.
parent 2faa55fb
Show whitespace changes
Inline Side-by-side
Showing with 52 additions and 37 deletions
turnkeylaser.py
View file @ 19c67c85
...@@ -70,6 +70,16 @@ Changelog 2015-04-11 ...@@ -70,6 +70,16 @@ Changelog 2015-04-11
Added back in raster optimising, it's not perfect but it's mostly there. Only a little slow parsing white vertical space now. Added back in raster optimising, it's not perfect but it's mostly there. Only a little slow parsing white vertical space now.
Found that raster optimisation code seems to be changing the pixel data at the end of the line somewhere. I'm not sure how since it's meant to just be cutting part of the data line out not changing it. will need to investigate further. Found that raster optimisation code seems to be changing the pixel data at the end of the line somewhere. I'm not sure how since it's meant to just be cutting part of the data line out not changing it. will need to investigate further.
Added option to the menu for users to disable raster optimisations. Added option to the menu for users to disable raster optimisations.
Changelog 2015-05-09
Spent a day stuffing around with the exporter and marlin firmware to figure out why pronterface was throwing checksum errors when
sending lots of G02 and G03 arc vector cuts. It turns out that with too much precision in the cuts marlin's buffer fills up and it's
unable to receive any more serial data. I resolved this by reducing the float point precision down to 3 decimal places and shifting
power and pulse settings to the G00 move command that comes before a set of G01, G02 and G03 commands to limit data that's needed to
be sent over the wire.
I also fixed up the part of the exporter to allow the offset and scaling functions to work. Though I found that looking at the scaling
code it will only scale from the original 0,0 coordinate, it doesn't scale based on a centre point.
""" """
### ###
...@@ -456,7 +466,7 @@ class Gcode_tools(inkex.Effect): ...@@ -456,7 +466,7 @@ class Gcode_tools(inkex.Effect):
self.OptionParser.add_option("", "--unit", action="store", type="string", dest="unit", default="G21 (All units in mm)\n", help="Units") self.OptionParser.add_option("", "--unit", action="store", type="string", dest="unit", default="G21 (All units in mm)\n", help="Units")
self.OptionParser.add_option("", "--function", action="store", type="string", dest="function", default="Curve", help="What to do: Curve|Area|Area inkscape") self.OptionParser.add_option("", "--function", action="store", type="string", dest="function", default="Curve", help="What to do: Curve|Area|Area inkscape")
self.OptionParser.add_option("", "--tab", action="store", type="string", dest="tab", default="", help="Means nothing right now. Notebooks Tab.") self.OptionParser.add_option("", "--tab", action="store", type="string", dest="tab", default="", help="Means nothing right now. Notebooks Tab.")
self.OptionParser.add_option("", "--generate_not_parametric_code",action="store", type="inkbool", dest="generate_not_parametric_code", default=False,help="Generated code will be not parametric.") #self.OptionParser.add_option("", "--generate_not_parametric_code",action="store", type="inkbool", dest="generate_not_parametric_code", default=False,help="Generated code will be not parametric.")
self.OptionParser.add_option("", "--double_sided_cutting",action="store", type="inkbool", dest="double_sided_cutting", default=False,help="Generate code for double-sided cutting.") self.OptionParser.add_option("", "--double_sided_cutting",action="store", type="inkbool", dest="double_sided_cutting", default=False,help="Generate code for double-sided cutting.")
self.OptionParser.add_option("", "--draw-curves", action="store", type="inkbool", dest="drawCurves", default=False,help="Draws curves to show what geometry was processed") self.OptionParser.add_option("", "--draw-curves", action="store", type="inkbool", dest="drawCurves", default=False,help="Draws curves to show what geometry was processed")
self.OptionParser.add_option("", "--logging", action="store", type="inkbool", dest="logging", default=False, help="Enable output logging from the plugin") self.OptionParser.add_option("", "--logging", action="store", type="inkbool", dest="logging", default=False, help="Enable output logging from the plugin")
...@@ -587,18 +597,19 @@ class Gcode_tools(inkex.Effect): ...@@ -587,18 +597,19 @@ class Gcode_tools(inkex.Effect):
if c[5] == 0: if c[5] == 0:
c[5] = None c[5] = None
# next few lines generate the stuff at the front of the file - scaling, offsets, etc (adina) # next few lines generate the stuff at the front of the file - scaling, offsets, etc (adina)
if self.options.generate_not_parametric_code: #if self.options.generate_not_parametric_code:
s = ["X", "Y", "Z", "I", "J", "K"] s = ["X", "Y", "Z", "I", "J", "K"]
s1 = ["","","","","",""] s1 = ["","","","","",""]
m = [self.options.Xscale, -self.options.Yscale, 1, m = [self.options.Xscale, -self.options.Yscale, 1,
self.options.Xscale, -self.options.Yscale, 1] self.options.Xscale, -self.options.Yscale, 1]
a = [self.options.Xoffset, self.options.Yoffset, 0, 0, 0, 0] a = [self.options.Xoffset, self.options.Yoffset, 0, 0, 0, 0]
else:
s = ["X", "Y", "Z", "I", "J", "K"] # else:
s1 = ["", "", "", "", "", ""] # s = ["X", "Y", "Z", "I", "J", "K"]
m = [1, -1, 1, 1, -1, 1] # s1 = ["", "", "", "", "", ""]
a = [0, 0, 0, 0, 0, 0] # m = [1, -1, 1, 1, -1, 1]
# a = [0, 0, 0, 0, 0, 0]
#There's no aphrodisiac like loneliness #There's no aphrodisiac like loneliness
#Add the page height if the origin is the bottom left. #Add the page height if the origin is the bottom left.
...@@ -609,7 +620,7 @@ class Gcode_tools(inkex.Effect): ...@@ -609,7 +620,7 @@ class Gcode_tools(inkex.Effect):
for i in range(6): for i in range(6):
if c[i]!=None: if c[i]!=None:
value = self.unitScale*(c[i]*m[i]+a[i]) value = self.unitScale*(c[i]*m[i]+a[i])
args.append(s[i] + ("%f" % value) + s1[i]) args.append(s[i] + ("%.3f" % value) + s1[i])
return " ".join(args) return " ".join(args)
...@@ -621,15 +632,18 @@ class Gcode_tools(inkex.Effect): ...@@ -621,15 +632,18 @@ class Gcode_tools(inkex.Effect):
# Use the "alternative" feed rate specified # Use the "alternative" feed rate specified
cutFeed = "F%i" % altfeed cutFeed = "F%i" % altfeed
else: else:
if self.options.generate_not_parametric_code: #if self.options.generate_not_parametric_code:
cutFeed = "F%i" % self.options.feed # cutFeed = "F%i" % self.options.feed
else: #else:
cutFeed = "F%i" % self.options.feed cutFeed = "F%i" % self.options.feed
#This extension assumes that your copy of Inkscape is running at 90dpi (it is by default) #This extension assumes that your copy of Inkscape is running at 90dpi (it is by default)
#R = mm per pixel #R = mm per pixel
#R = 1 / dots per mm #R = 1 / dots per mm
#90dpi = 1 / (90 / 25.4) #90dpi = 1 / (90 / 25.4)
#Rasters are exported internally at 270dpi.
#So R = 1 / (270 / 25.4)
# = 0.09406
gcode += '\n\n;Beginning of Raster Image '+str(curve['id'])+' pixel size: '+str(curve['width'])+'x'+str(curve['height'])+'\n' gcode += '\n\n;Beginning of Raster Image '+str(curve['id'])+' pixel size: '+str(curve['width'])+'x'+str(curve['height'])+'\n'
gcode += 'M649 S'+str(laserPower)+' B2 D0 R0.09406\n' gcode += 'M649 S'+str(laserPower)+' B2 D0 R0.09406\n'
...@@ -791,9 +805,6 @@ class Gcode_tools(inkex.Effect): ...@@ -791,9 +805,6 @@ class Gcode_tools(inkex.Effect):
if (altfeed): if (altfeed):
# Use the "alternative" feed rate specified # Use the "alternative" feed rate specified
cutFeed = "F%i" % altfeed cutFeed = "F%i" % altfeed
else:
if self.options.generate_not_parametric_code:
cutFeed = "F%i" % self.options.feed
else: else:
cutFeed = "F%i" % self.options.feed cutFeed = "F%i" % self.options.feed
...@@ -821,10 +832,10 @@ class Gcode_tools(inkex.Effect): ...@@ -821,10 +832,10 @@ class Gcode_tools(inkex.Effect):
#G00 : Move with the laser off to a new point #G00 : Move with the laser off to a new point
if s[1] == 'move': if s[1] == 'move':
#Turn off the laser if it was on previously. #Turn off the laser if it was on previously.
if lg != "G00": #if lg != "G00":
gcode += LASER_OFF + "\n" # gcode += LASER_OFF + "\n"
gcode += "G00" + " " + self.make_args(si[0]) + " F%i" % self.options.Mfeed + "\n" gcode += "G00" + " S%.2f " % laserPower + self.make_args(si[0]) + " F%i " % self.options.Mfeed + "%s" % ppmValue + "\n"
lg = 'G00' lg = 'G00'
elif s[1] == 'end': elif s[1] == 'end':
...@@ -832,7 +843,7 @@ class Gcode_tools(inkex.Effect): ...@@ -832,7 +843,7 @@ class Gcode_tools(inkex.Effect):
#G01 : Move with the laser turned on to a new point #G01 : Move with the laser turned on to a new point
elif s[1] == 'line': elif s[1] == 'line':
gcode += "G01 " + "S%.2f " % laserPower + self.make_args(si[0]) + " %s " % cutFeed + "%s" % ppmValue + "\n" gcode += "G01 " + "S%.2f " % laserPower + self.make_args(si[0]) + " %s " % cutFeed + "\n"
lg = 'G01' lg = 'G01'
#G02 and G03 : Move in an arc with the laser turned on. #G02 and G03 : Move in an arc with the laser turned on.
...@@ -847,7 +858,7 @@ class Gcode_tools(inkex.Effect): ...@@ -847,7 +858,7 @@ class Gcode_tools(inkex.Effect):
gcode += cwArc gcode += cwArc
else: else:
gcode += ccwArc gcode += ccwArc
gcode += " " + "S%.2f " % laserPower + self.make_args(si[0] + [None, dx, dy, None]) + " %s " % cutFeed + "%s" % ppmValue + "\n" gcode += " " + self.make_args(si[0] + [None, dx, dy, None]) + " %s " % cutFeed + "\n"
else: else:
r = (r1.mag()+r2.mag())/2 r = (r1.mag()+r2.mag())/2
...@@ -855,12 +866,12 @@ class Gcode_tools(inkex.Effect): ...@@ -855,12 +866,12 @@ class Gcode_tools(inkex.Effect):
gcode += cwArc gcode += cwArc
else: else:
gcode += ccwArc gcode += ccwArc
gcode += " " + "S%.2f " % laserPower + self.make_args(si[0]) + " R%f" % (r*self.options.Xscale) + " %s " % cutFeed + "%s" % ppmValue + "\n" gcode += " " + "S%.2f " % laserPower + self.make_args(si[0]) + " R%f" % (r*self.options.Xscale) + " %s " % cutFeed + "\n"
lg = cwArc lg = cwArc
#The arc is less than the minimum arc radius, draw it as a straight line. #The arc is less than the minimum arc radius, draw it as a straight line.
else: else:
gcode += "G01 " + "S%.2f " % laserPower + self.make_args(si[0]) + " %s " % cutFeed + "%s" % ppmValue + "\n" gcode += "G01 " + "S%.2f " % laserPower + self.make_args(si[0]) + " %s " % cutFeed + "\n"
lg = 'G01' lg = 'G01'
...@@ -928,7 +939,7 @@ class Gcode_tools(inkex.Effect): ...@@ -928,7 +939,7 @@ class Gcode_tools(inkex.Effect):
simpletransform.applyTransformToPath(trans, csp) simpletransform.applyTransformToPath(trans, csp)
path['data'] = csp path['data'] = csp
#Apply a transoform in the Y plan to flip the path vertically #Apply a transform in the Y plan to flip the path vertically
#If we want our origin to the the top left. #If we want our origin to the the top left.
if (self.options.origin == 'topleft'): if (self.options.origin == 'topleft'):
csp = path['data'] csp = path['data']
...@@ -1215,7 +1226,12 @@ class Gcode_tools(inkex.Effect): ...@@ -1215,7 +1226,12 @@ class Gcode_tools(inkex.Effect):
#Turnkey - Need to figure out why inkscape sometimes gets to this point and hasn't found the objects above. #Turnkey - Need to figure out why inkscape sometimes gets to this point and hasn't found the objects above.
# If there are any objects left over, it's because they don't belong # If there are any objects left over, it's because they don't belong
# to any inkscape layer (bug in inkscape?). Output those now. # to any inkscape layer (bug in inkscape?). Output those now.
#Turnkey - This is caused by objects being inside a group.
if (selected): if (selected):
inkex.errormsg("Warning: Your selected object is part of a group. If your group has a transformations/skew/rotation applied to it these will not be exported correctly. Please ungroup your objects first then re-export. Select them and press Shift+Ctrl+G to ungroup.\n")
pathList = [] pathList = []
# Use the identity transform (eg no transform) for the root objects # Use the identity transform (eg no transform) for the root objects
trans = simpletransform.parseTransform("") trans = simpletransform.parseTransform("")
...@@ -1341,7 +1357,7 @@ class Gcode_tools(inkex.Effect): ...@@ -1341,7 +1357,7 @@ class Gcode_tools(inkex.Effect):
inkex.errormsg(("You must choose mm or in")) inkex.errormsg(("You must choose mm or in"))
return return
if not self.options.generate_not_parametric_code: #Put the header data in the gcode file
gcode += """ gcode += """
; Raster data will always precede vector data ; Raster data will always precede vector data
; Default Cut Feedrate %i mm per minute ; Default Cut Feedrate %i mm per minute
...@@ -1365,7 +1381,7 @@ class Gcode_tools(inkex.Effect): ...@@ -1365,7 +1381,7 @@ class Gcode_tools(inkex.Effect):
self.options.Yscale *= -1 self.options.Yscale *= -1
self.flipArcs = not(self.flipArcs) self.flipArcs = not(self.flipArcs)
self.options.generate_not_parametric_code = True #self.options.generate_not_parametric_code = True
self.pageHeight = 0 self.pageHeight = 0
gcode += self.effect_curve(selected) gcode += self.effect_curve(selected)
...@@ -1383,4 +1399,3 @@ class Gcode_tools(inkex.Effect): ...@@ -1383,4 +1399,3 @@ class Gcode_tools(inkex.Effect):
e = Gcode_tools() e = Gcode_tools()
e.affect() e.affect()
inkex.errormsg("Finished processing.") inkex.errormsg("Finished processing.")
\ No newline at end of file
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment