/****************************************************************************************
* 84
* Teensy++ 2.0 Breadboard pin assignments (AT90USB1286)
* Requires the Teensyduino software with Teensy++ 2.0 selected in Arduino IDE!
* http://www.pjrc.com/teensy/teensyduino.html
* See http://reprap.org/wiki/Printrboard for more info
* CLI build: DEFINES=AT90USBxx_TEENSYPP_ASSIGNMENTS HARDWARE_MOTHERBOARD=84 make
****************************************************************************************/
#define KNOWN_BOARD 1
#define AT90USB 1286 // Disable MarlinSerial etc.
#ifndef __AVR_AT90USB1286__
#error Oops! Make sure you have 'Teensy++ 2.0' selected from the 'Tools -> Boards' menu.
#endif
#define LARGE_FLASH true
/*
DaveX plan for Teensylu/printrboard-type pinouts (ref teensylu & sprinter) for a TeensyBreadboard:
USB
GND GND |-----#####-----| +5V ATX +5SB
ATX PS_ON PWM 27 |b7 ##### b6| 26 PWM* Stepper Enable
PWM 0 |d0 b5| 25 PWM*
PWM 1 |d1 b4| 24 PWM
X_MIN 2 |d2 b3| 23 MISO_PIN
Y_MIN 3 |d3 b2| 22 MOSI_PIN
Z_MIN 4 |d4 * * b1| 21 SCK_PIN
5 |d5 e e b0| 20 SDSS
LED 6 |d6 5 4 e7| 19
7 |d7 e6| 18
LCD RS 8 |e0 | GND
LCD EN 9 |e1 a4 a0 R| AREF
LCD D4 10 |c0 a5 a1 f0| 38 A0 ENC_1
LCD D5 11 |c1 a6 a2 f1| 39 A1 ENC_2
LCD D6 12 |c2 a7 a3 f2| 40 A2 ENC_CLK
LCD D6 13 |c3 f3| 41 A3
Bed Heat PWM 14 |c4 V G R f4| 42 A4
Extruder Heat PWM 15 |c5 c n S f5| 43 A5
Fan PWM 16 |c6 c d T f6| 44 A6 Bed TC
17 |c7 * * * f7| 45 A7 Extruder TC * 4.7k * +5
-----------------
Interior E4: 36, INT4
Interior E5: 37, INT5
Interior PA0-7: 28-35 -- Printrboard and Teensylu use these pins for step & direction:
T++ PA Signal Marlin
Z STEP 32 a4 a0 28 X STEP
Z DIR 33 a5 a1 29 X DIR
E STEP 34 a6 a2 30 Y STEP
E DIR 35 a7 a3 31 Y DIR
*/
#ifndef AT90USBxx_TEENSYPP_ASSIGNMENTS // use Teensyduino Teensy++2.0 pin assignments instead of Marlin alphabetical.
#error Uncomment #define AT90USBxx_TEENSYPP_ASSIGNMENTS in fastio.h for this config
// or build from command line with: DEFINES=AT90USBxx_TEENSYPP_ASSIGNMENTS HARDWARE_MOTHERBOARD=84 make
#endif
#define ORIG_X_STEP_PIN 28 // 0 Marlin
#define ORIG_X_DIR_PIN 29 // 1 Marlin
#define ORIG_X_ENABLE_PIN 26
#define ORIG_Y_STEP_PIN 30 // 2 Marlin
#define ORIG_Y_DIR_PIN 31 // 3
#define ORIG_Y_ENABLE_PIN 26 // Shared w/x
#define ORIG_Z_STEP_PIN 32 // 4
#define ORIG_Z_DIR_PIN 33 // 5
#define ORIG_Z_ENABLE_PIN 26 // Shared w/x
#define ORIG_E0_STEP_PIN 34 // 6
#define ORIG_E0_DIR_PIN 35 // 7
#define ORIG_E0_ENABLE_PIN 26 // Shared w/x
#define ORIG_HEATER_0_PIN 15 // 21 // Extruder
#define ORIG_HEATER_1_PIN -1
#define ORIG_HEATER_2_PIN -1
#define ORIG_HEATER_BED_PIN 14 // 20 // Bed
#define ORIG_FAN_PIN 16 // 22 // Fan
#define X_STOP_PIN 2
#define Y_STOP_PIN 3
#define Z_STOP_PIN 4
#define ORIG_TEMP_0_PIN 7 // Extruder / Analog pin numbering
#define ORIG_TEMP_BED_PIN 6 // Bed / Analog pin numbering
#define ORIG_TEMP_1_PIN -1
#define ORIG_TEMP_2_PIN -1
#define SDPOWER -1
#define SD_DETECT_PIN -1
#define SDSS 20 // 8
#define LED_PIN 6
#define ORIG_PS_ON_PIN 27
#define KILL_PIN -1
#define ALARM_PIN -1
#if ENABLED(ULTIPANEL)
#define LCD_PINS_RS 8
#define LCD_PINS_ENABLE 9
#define LCD_PINS_D4 10
#define LCD_PINS_D5 11
#define LCD_PINS_D6 12
#define LCD_PINS_D7 13
#define BTN_EN1 38
#define BTN_EN2 39
#define BTN_ENC 40
#endif