/****************************************************************************************
* 6 - 62 - 63 - 64 - 65
*  6 - Sanguinololu <1.2
* 62 - Sanguinololu 1.2 and above
* 63 - Melzi
* 64 - STB 1.1
* 65 - Azteeg X1
* 66 - MELZI 1284
****************************************************************************************/

 #if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega1284P__)
    #error Oops!  Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu.
  #endif

  #define KNOWN_BOARD 1

  #if !MB(SANGUINOLOLU_11)
    #define SANGUINOLOLU_V_1_2
  #endif

  #if defined(__AVR_ATmega1284P__)
    #define LARGE_FLASH true
  #endif

  #define ORIG_X_STEP_PIN         15
  #define ORIG_X_DIR_PIN          21
  #define X_STOP_PIN              18

  #define ORIG_Y_STEP_PIN         22
  #define ORIG_Y_DIR_PIN          23
  #define Y_STOP_PIN              19

  #define ORIG_Z_STEP_PIN          3
  #define ORIG_Z_DIR_PIN           2
  #define Z_STOP_PIN              20

  #define ORIG_E0_STEP_PIN         1
  #define ORIG_E0_DIR_PIN          0

  #define LED_PIN                 -1

  #define ORIG_FAN_PIN            -1

  #if ORIG_FAN_PIN == 12 || ORIG_FAN_PIN ==13
    #define FAN_SOFT_PWM
  #endif

  #if MB(AZTEEG_X1) || MB(STB_11) || MB(MELZI)
    #define ORIG_FAN_PIN           4 // Works for Panelolu2 too
    #if MB(MELZI)
      #define LED_PIN             27
    #elif MB(STB_11)
      #define LCD_PIN_BL          17 // LCD backlight LED
    #endif
  #endif

  #if NUM_SERVOS > 0
    #define SERVO0_PIN            -1
    #if NUM_SERVOS > 1
      #define SERVO1_PIN          -1
      #if NUM_SERVOS > 2
        #define SERVO2_PIN        -1
        #if NUM_SERVOS > 3
          #define SERVO3_PIN      -1
        #endif
      #endif
    #endif
  #endif

  #define ORIG_PS_ON_PIN          -1
  #define KILL_PIN                -1

  #define ORIG_HEATER_0_PIN       13 // (extruder)
  #define ORIG_HEATER_1_PIN       -1
  #define ORIG_HEATER_2_PIN       -1

  #if ENABLED(SANGUINOLOLU_V_1_2)

    #define ORIG_HEATER_BED_PIN   12 // (bed)
    #define ORIG_X_ENABLE_PIN     14
    #define ORIG_Y_ENABLE_PIN     14
    #define ORIG_Z_ENABLE_PIN     26
    #define ORIG_E0_ENABLE_PIN    14

    #if ENABLED(LCD_I2C_PANELOLU2)
      #define ORIG_FAN_PIN         4 // Uses Transistor1 (PWM) on Panelolu2's Sanguino Adapter Board to drive the fan
    #endif

  #else

    #define ORIG_HEATER_BED_PIN   14  // (bed)
    #define ORIG_X_ENABLE_PIN     -1
    #define ORIG_Y_ENABLE_PIN     -1
    #define ORIG_Z_ENABLE_PIN     -1
    #define ORIG_E0_ENABLE_PIN    -1

  #endif

    #define ORIG_TEMP_0_PIN        7   // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 33 extruder)
    #define ORIG_TEMP_1_PIN       -1
    #define ORIG_TEMP_2_PIN       -1
    #define ORIG_TEMP_BED_PIN      6   // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 34 bed)
    #define SDPOWER               -1
    #define SDSS                  31

  /**
   * On some broken versions of the Sanguino libraries the pin definitions are wrong,
   * which then needs SDSS as pin 24. But you should upgrade your Sanguino libraries! See #368.
   */
  //#define SDSS               24

  #if ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL)

    // No buzzer installed
    #define ORIG_BEEPER_PIN -1

    //LCD Pins
    #if ENABLED(DOGLCD)

      #if ENABLED(U8GLIB_ST7920) //SPI GLCD 12864 ST7920 ( like [www.digole.com] ) For Melzi V2.0
        #if MB(MELZI) // Melzi board
          #define LCD_PINS_RS     30 //CS chip select /SS chip slave select
          #define LCD_PINS_ENABLE 29 //SID (MOSI)
          #define LCD_PINS_D4     17 //SCK (CLK) clock
          #define ORIG_BEEPER_PIN 27 // Pin 27 is taken by LED_PIN, but Melzi LED does nothing with Marlin so this can be used for ORIG_BEEPER_PIN. You can use this pin with M42 instead of ORIG_BEEPER_PIN.
        #else         // Sanguinololu 1.3
          #define LCD_PINS_RS      4
          #define LCD_PINS_ENABLE 17
          #define LCD_PINS_D4     30
          #define LCD_PINS_D5     29
          #define LCD_PINS_D6     28
          #define LCD_PINS_D7     27
        #endif
      #else // DOGM SPI LCD Support

        #define DOGLCD_A0         30
        #define DOGLCD_CS         29
        #define LCD_CONTRAST       1
      #endif

      // Uncomment screen orientation
      #define LCD_SCREEN_ROT_0
      //#define LCD_SCREEN_ROT_90
      //#define LCD_SCREEN_ROT_180
      //#define LCD_SCREEN_ROT_270

    #else // !DOGLCD - Standard Hitachi LCD controller
      #define LCD_PINS_RS          4
      #define LCD_PINS_ENABLE     17
      #define LCD_PINS_D4         30
      #define LCD_PINS_D5         29
      #define LCD_PINS_D6         28
      #define LCD_PINS_D7         27
    #endif // !DOGLCD

    //The encoder and click button
    #define BTN_EN1               11
    #define BTN_EN2               10
    #if ENABLED(LCD_I2C_PANELOLU2)
      #if MB(MELZI)
        #define BTN_ENC           29
        #define LCD_SDSS          30 // Panelolu2 SD card reader rather than the Melzi
      #else
        #define BTN_ENC           30
      #endif
    #else
      #define BTN_ENC             16
      #define LCD_SDSS            28 // Smart Controller SD card reader rather than the Melzi
    #endif //Panelolu2

    #define SD_DETECT_PIN         -1

  #elif ENABLED(MAKRPANEL)
    #define ORIG_BEEPER_PIN       29

    // Pins for DOGM SPI LCD Support
    #define DOGLCD_A0             30
    #define DOGLCD_CS             17
    #define LCD_PIN_BL            28 // backlight LED on PA3
    // GLCD features
    #define LCD_CONTRAST           1
    // Uncomment screen orientation
    #define LCD_SCREEN_ROT_0
    //#define LCD_SCREEN_ROT_90
    //#define LCD_SCREEN_ROT_180
    //#define LCD_SCREEN_ROT_270
    //The encoder and click button
    #define BTN_EN1               11
    #define BTN_EN2               10
    #define BTN_ENC               16

    #define SD_DETECT_PIN         -1

  #endif // MAKRPANEL