/****************************************************************************************
* 10 BOARD_GEN7_CUSTOM - Gen7 custom (Alfons3 Version)
* 11 BOARD_GEN7_12 - Gen7 v1.1, v1.2
* 12 BOARD_GEN7_13 - Gen7 v1.3
* 12 BOARD_GEN7_14 - Gen7 v1.4
*
*  2 BOARD_CHEAPTRONIC - Cheaptronic v1.0
* 20 BOARD_SETHI - Sethi 3D_1
* 21 BOARD_ELEFU_3 - Elefu Ra Board (v3)
* 22 BOARD_GEN3_MONOLITHIC - Gen3 Monolithic Electronics
*
*  3 BOARD_RAMPS_OLD - MEGA/RAMPS up to 1.2
* 33 BOARD_RAMPS_13_EFB - RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Bed)
* 34 BOARD_RAMPS_13_EEB - RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Bed)
* 35 BOARD_RAMPS_13_EFF - RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Fan)
* 36 BOARD_RAMPS_13_EEF - RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Fan)
*
*301 BOARD_RAMBO - Rambo
*
*  4 BOARD_DUEMILANOVE_328P - Duemilanove w/ ATMega328P pin assignment
*
*  5 BOARD_GEN6 - Gen6
* 51 BOARD_GEN6_DELUXE - Gen6 deluxe
*
*  6 BOARD_SANGUINOLOLU_11 - Sanguinololu < 1.2
* 62 BOARD_SANGUINOLOLU_12 - Sanguinololu 1.2 and above
* 63 BOARD_MELZI - Melzi
* 64 BOARD_STB_11 - STB V1.1
* 65 BOARD_AZTEEG_X1 - Azteeg X1
* 66 BOARD_MELZI_1284 - Melzi with ATmega1284 (MaKr3d version)
* 67 BOARD_AZTEEG_X3 - Azteeg X3
* 68 BOARD_AZTEEG_X3_PRO - Azteeg X3 Pro
*
*  7 BOARD_ULTIMAKER - Ultimaker
*
* 70 BOARD_MEGATRONICS   - Megatronics
*701 BOARD_MEGATRONICS_2 - Megatronics v2.0
*702 BOARD_MEGATRONICS_1 - Minitronics v1.0
*703 BOARD_MEGATRONICS_3 - Megatronics v3.0
* 71 BOARD_ULTIMAKER_OLD - Ultimaker (Older electronics. Pre 1.5.4. This is rare)
* 72 BOARD_ULTIMAIN_2 - Ultimainboard 2.x (Uses TEMP_SENSOR 20)
* 77 BOARD_3DRAG - 3Drag Controller
* 78 BOARD_K8200 - Vellemann K8200 Controller (derived from 3Drag Controller)
*
*  8 BOARD_TEENSYLU - Teensylu
* 80 BOARD_RUMBA - Rumba
* 81 BOARD_PRINTRBOARD - Printrboard (AT90USB1286)
* 82 BOARD_BRAINWAVE - Brainwave (AT90USB646)
* 83 BOARD_SAV_MKI - SAV Mk-I (AT90USB1286)
* 84 BOARD_TEENSY2 - Teensy++2.0 (AT90USB1286)
* 88 BOARD_5DPRINT - 5DPrint D8 Driver Board
*
*  9 BOARD_GEN3_PLUS - Gen3+
* 90 BOARD_OMCA_A - Alpha OMCA board
* 91 BOARD_OMCA - Final OMCA board
*999 BOARD_LEAPFROG - Leapfrog
*
*99 BOARD_99 - Custom motherboard
****************************************************************************************/

#ifndef PINS_H
#define PINS_H

#include "boards.h"

#if !MB(5DPRINT)
#define X_MS1_PIN -1
#define X_MS2_PIN -1
#define Y_MS1_PIN -1
#define Y_MS2_PIN -1
#define Z_MS1_PIN -1
#define Z_MS2_PIN -1
#define E0_MS1_PIN -1
#define E0_MS2_PIN -1
#define E1_MS1_PIN -1
#define E1_MS2_PIN -1
#define DIGIPOTSS_PIN -1
#endif


/******************************************************************************
* 10
* Gen7 Alfons
* These Pins are assigned for the modified GEN7
* Board from Alfons3 Please review the pins and adjust it for your needs
******************************************************************************/

#if MB(GEN7_CUSTOM)
  #define KNOWN_BOARD

  #if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__)
    #error Oops!  Make sure you have 'Gen7' selected from the 'Tools -> Boards' menu.
  #endif

  //X axis pins
  #define ORIG_X_STEP_PIN       21  // different from standard GEN7
  #define ORIG_X_DIR_PIN        20  // different from standard GEN7
  #define ORIG_X_ENABLE_PIN     24
  #define X_STOP_PIN            0

  //Y axis pins
  #define ORIG_Y_STEP_PIN       23
  #define ORIG_Y_DIR_PIN        22
  #define ORIG_Y_ENABLE_PIN     24
  #define Y_STOP_PIN            1

  //Z axis pins
  #define ORIG_Z_STEP_PIN       26
  #define ORIG_Z_DIR_PIN        25
  #define ORIG_Z_ENABLE_PIN     24
  #define Z_STOP_PIN            2
  
  //extruder pins
  #define ORIG_E0_STEP_PIN      28
  #define ORIG_E0_DIR_PIN       27
  #define ORIG_E0_ENABLE_PIN    24
  
  #define ORIG_TEMP_0_PIN       2
  #define ORIG_TEMP_1_PIN       -1
  #define ORIG_TEMP_2_PIN       -1
  #define ORIG_TEMP_BED_PIN     1  // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 34 bed)
 
  #define ORIG_HEATER_0_PIN     4
  #define ORIG_HEATER_1_PIN     -1
  #define ORIG_HEATER_2_PIN     -1
  #define ORIG_HEATER_BED_PIN   3  // (bed)
  
  #define SDPOWER               -1
  #define SDSS                  31  // SCL pin of I2C header || CS Pin for SD Card support
  #define LED_PIN               -1
  
  #define ORIG_FAN_PIN          -1
  #define PS_ON_PIN             19
  
  //our pin for debugging.
  #define DEBUG_PIN             -1
  
  //our RS485 pins
  //#define TX_ENABLE_PIN       12
  //#define RX_ENABLE_PIN       13
  
  #define BEEPER                -1
  #define SDCARDDETECT          -1
  #define SUICIDE_PIN           -1  //has to be defined; otherwise Power_off doesn't work
  
  #define KILL_PIN              -1
  //Pins for 4bit LCD Support
  #define LCD_PINS_RS           18
  #define LCD_PINS_ENABLE       17
  #define LCD_PINS_D4           16
  #define LCD_PINS_D5           15
  #define LCD_PINS_D6           13
  #define LCD_PINS_D7           14
  
  //buttons are directly attached
  #define BTN_EN1               11
  #define BTN_EN2               10
  #define BTN_ENC               12  //the click

#endif // GEN7_CUSTOM
/****************************************************************************************/



/****************************************************************************************
* 11
* Gen7 v1.1, v1.2
****************************************************************************************/

#if MB(GEN7_12)
  #define KNOWN_BOARD
  
  #if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__)
    #error Oops! Make sure you have 'Gen7' selected from the 'Tools -> Boards' menu.
  #endif
  
  #ifndef GEN7_VERSION
    #define GEN7_VERSION          12  // v1.x
  #endif
  
  //X axis pins
  #define ORIG_X_STEP_PIN       19
  #define ORIG_X_DIR_PIN        18
  #define ORIG_X_ENABLE_PIN     24
  #define X_STOP_PIN             7
  
  //Y axis pins
  #define ORIG_Y_STEP_PIN       23
  #define ORIG_Y_DIR_PIN        22
  #define ORIG_Y_ENABLE_PIN     24
  #define Y_STOP_PIN             5
  
  //Z axis pins
  #define ORIG_Z_STEP_PIN       26
  #define ORIG_Z_DIR_PIN        25
  #define ORIG_Z_ENABLE_PIN     24
  #define ORIG_Z_MIN_PIN         1
  #define ORIG_Z_MAX_PIN         0
  
  //extruder pins
  #define ORIG_E0_STEP_PIN      28
  #define ORIG_E0_DIR_PIN       27
  #define ORIG_E0_ENABLE_PIN    24
  
  #define ORIG_TEMP_0_PIN        1
  #define ORIG_TEMP_1_PIN       -1
  #define ORIG_TEMP_2_PIN       -1
  #define ORIG_TEMP_BED_PIN      2
  
  #define ORIG_HEATER_0_PIN      4
  #define ORIG_HEATER_1_PIN     -1
  #define ORIG_HEATER_2_PIN     -1
  #define ORIG_HEATER_BED_PIN    3
  
  #define KILL_PIN              -1
  
  #define SDPOWER               -1
  #define SDSS                  -1  // SCL pin of I2C header
  #define LED_PIN               -1
  
  #define ORIG_FAN_PIN          31
  #define PS_ON_PIN             15
  
  //All these generations of Gen7 supply thermistor power
  //via PS_ON, so ignore bad thermistor readings
  #define BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE
  
  //our pin for debugging.
  #define DEBUG_PIN              0
  
  //our RS485 pins
  #define TX_ENABLE_PIN         12
  #define RX_ENABLE_PIN         13

#endif
/****************************************************************************************/



/****************************************************************************************
* 12
* Gen7 v1.3
****************************************************************************************/

#if MB(GEN7_13)
  #define KNOWN_BOARD
  
  #if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__)
    #error Oops! Make sure you have 'Gen7' selected from the 'Tools -> Boards' menu.
  #endif
  
  #ifndef GEN7_VERSION
    #define GEN7_VERSION        13  // v1.x
  #endif
  
  //X axis pins
  #define ORIG_X_STEP_PIN       19
  #define ORIG_X_DIR_PIN        18
  #define ORIG_X_ENABLE_PIN     24
  #define X_STOP_PIN             7
  
  //Y axis pins
  #define ORIG_Y_STEP_PIN       23
  #define ORIG_Y_DIR_PIN        22
  #define ORIG_Y_ENABLE_PIN     24
  #define Y_STOP_PIN             5
  
  //Z axis pins
  #define ORIG_Z_STEP_PIN       26
  #define ORIG_Z_DIR_PIN        25
  #define ORIG_Z_ENABLE_PIN     24
  #define ORIG_Z_MIN_PIN         1
  #define ORIG_Z_MAX_PIN         0
  
  //extruder pins
  #define ORIG_E0_STEP_PIN      28
  #define ORIG_E0_DIR_PIN       27
  #define ORIG_E0_ENABLE_PIN    24
  
  #define ORIG_TEMP_0_PIN        1
  #define ORIG_TEMP_1_PIN       -1
  #define ORIG_TEMP_2_PIN       -1
  #define ORIG_TEMP_BED_PIN      2
  
  #define ORIG_HEATER_0_PIN      4
  #define ORIG_HEATER_1_PIN     -1
  #define ORIG_HEATER_2_PIN     -1
  #define ORIG_HEATER_BED_PIN    3
  
  #define KILL_PIN              -1
  
  #define SDPOWER               -1
  #define SDSS                  -1  // SCL pin of I2C header
  #define LED_PIN               -1
  
  #define ORIG_FAN_PIN          -1  // Gen7 v1.3 removed the fan pin
  #define PS_ON_PIN             15
  
  //All these generations of Gen7 supply thermistor power
  //via PS_ON, so ignore bad thermistor readings
  #define BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE
  
  //our pin for debugging.
  #define DEBUG_PIN              0
  
  //our RS485 pins
  #define TX_ENABLE_PIN         12
  #define RX_ENABLE_PIN         13

#endif
/****************************************************************************************/



/****************************************************************************************
* 13
* Gen7 v1.4 pin assignment
****************************************************************************************/

#if MB(GEN7_14)
  #define GEN7_VERSION        14 // v1.4
  #define KNOWN_BOARD
  
  #if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__)
    #error Oops! Make sure you have 'Gen7' selected from the 'Tools -> Boards' menu.
  #endif
  
  //X axis pins
  #define ORIG_X_STEP_PIN       29
  #define ORIG_X_DIR_PIN        28
  #define ORIG_X_ENABLE_PIN     25
  #define X_STOP_PIN             0
  
  //Y axis pins
  #define ORIG_Y_STEP_PIN       27
  #define ORIG_Y_DIR_PIN        26
  #define ORIG_Y_ENABLE_PIN     25
  #define Y_STOP_PIN             1
  
  //Z axis pins
  #define ORIG_Z_STEP_PIN       23
  #define ORIG_Z_DIR_PIN        22
  #define ORIG_Z_ENABLE_PIN     25
  #define Z_STOP_PIN             2
  
  //extruder pins
  #define ORIG_E0_STEP_PIN      19
  #define ORIG_E0_DIR_PIN       18
  #define ORIG_E0_ENABLE_PIN    25
  
  #define ORIG_TEMP_0_PIN        1
  #define ORIG_TEMP_1_PIN       -1
  #define ORIG_TEMP_2_PIN       -1
  #define ORIG_TEMP_BED_PIN      0
  
  #define ORIG_HEATER_0_PIN      4
  #define ORIG_HEATER_1_PIN     -1
  #define ORIG_HEATER_2_PIN     -1
  #define ORIG_HEATER_BED_PIN    3
  
  #define KILL_PIN              -1

  #define SDPOWER               -1
  #define SDSS                  -1  // SCL pin of I2C header
  #define LED_PIN               -1

  #define ORIG_FAN_PIN          -1

  #define PS_ON_PIN             15

  //our pin for debugging.
  #define DEBUG_PIN              0

  //our RS485 pins
  #define TX_ENABLE_PIN         12
  #define RX_ENABLE_PIN         13

#endif // GEN7
/****************************************************************************************/



/****************************************************************************************
* 2
* Cheaptronic v1.0
****************************************************************************************/

#if MB(CHEAPTRONIC)
  #define KNOWN_BOARD 1
  
  #ifndef __AVR_ATmega2560__
    #error Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
  #endif
  
  #define LARGE_FLASH        true
  
  //X motor stepper
  #define ORIG_X_STEP_PIN 14
  #define ORIG_X_DIR_PIN 15
  #define ORIG_X_ENABLE_PIN 24
  
  //X endstop
  #define ORIG_X_MIN_PIN 3
  #define ORIG_X_MAX_PIN -1
  
  //Y motor stepper
  #define ORIG_Y_STEP_PIN 35
  #define ORIG_Y_DIR_PIN 36
  #define ORIG_Y_ENABLE_PIN 31
  
  //Y endstop
  #define ORIG_Y_MIN_PIN 2
  #define ORIG_Y_MAX_PIN -1
  
  //Z motor stepper
  #define ORIG_Z_STEP_PIN 40
  #define ORIG_Z_DIR_PIN 41
  #define ORIG_Z_ENABLE_PIN 37
  
  //Z endstop
  #define ORIG_Z_MIN_PIN 5
  #define ORIG_Z_MAX_PIN -1
  
  //Extruder 0 stepper
  #define ORIG_E0_STEP_PIN 26
  #define ORIG_E0_DIR_PIN 28
  #define ORIG_E0_ENABLE_PIN 25
  
  //Extruder 1 stepper
  #define ORIG_E1_STEP_PIN 33
  #define ORIG_E1_DIR_PIN 34
  #define ORIG_E1_ENABLE_PIN 30
  
  #define SDPOWER -1
  #define SDSS -1
  #define LED_PIN -1
  
  //FAN
  #define ORIG_FAN_PIN -1
  
  #define PS_ON_PIN -1
  #define KILL_PIN -1
  
  #define ORIG_HEATER_0_PIN 19 // EXTRUDER 1
  #define ORIG_HEATER_1_PIN 23 // EXTRUDER 2
  //HeatedBad
  #define ORIG_HEATER_BED_PIN 22
  //Cheaptronic v1.0 hasent EXTRUDER 3
  #define ORIG_HEATER_2_PIN -1
  
  //Temperature sensors
  #define ORIG_TEMP_0_PIN 15
  #define ORIG_TEMP_1_PIN 14
  #define ORIG_TEMP_2_PIN -1
  #define ORIG_TEMP_BED_PIN 13
  
  //Cheaptronic v1.0 dont support LCD
  #define LCD_PINS_RS -1
  #define LCD_PINS_ENABLE -1
  #define LCD_PINS_D4 -1
  #define LCD_PINS_D5 -1
  #define LCD_PINS_D6 -1
  #define LCD_PINS_D7 -1
  
  //Cheaptronic v1.0 dont support keypad
  #define BTN_EN1 -1
  #define BTN_EN2 -1
  #define BTN_ENC -1
  #define BLEN_C 2
  #define BLEN_B 1
  #define BLEN_A 0
  
  //Cheaptronic v1.0 does not use this port
  #define SDCARDDETECT -1
  
  //encoder rotation values
  #define encrot0 0
  #define encrot1 2
  #define encrot2 3
  #define encrot3 1

#endif // CHEAPTRONIC
/****************************************************************************************/



/****************************************************************************************
* 20
* Sethi 3D_1 pin assignment - www.sethi3d.com.br
****************************************************************************************/

#if MB(SETHI)
  #define KNOWN_BOARD
  
  #if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__)
    #error Oops! Make sure you have 'Sethi 3D' selected from the 'Tools -> Boards' menu.
  #endif
  
  #ifndef GEN7_VERSION
  #define GEN7_VERSION 12 // v1.x
  #endif
  
  //x axis pins
  #define ORIG_X_STEP_PIN 19
  #define ORIG_X_DIR_PIN 18
  #define ORIG_X_ENABLE_PIN 24
  #define X_STOP_PIN 2
  
  //y axis pins
  #define ORIG_Y_STEP_PIN 23
  #define ORIG_Y_DIR_PIN 22
  #define ORIG_Y_ENABLE_PIN 24
  #define Y_STOP_PIN 0
  
  //z axis pins
  #define ORIG_Z_STEP_PIN 26
  #define ORIG_Z_DIR_PIN 25
  #define ORIG_Z_ENABLE_PIN 24
  #define ORIG_Z_MIN_PIN 1
  #define ORIG_Z_MAX_PIN 0
  
  //extruder pins
  #define ORIG_E0_STEP_PIN 28
  #define ORIG_E0_DIR_PIN 27
  #define ORIG_E0_ENABLE_PIN 24
  
  #define ORIG_TEMP_0_PIN 1
  #define ORIG_TEMP_1_PIN -1
  #define ORIG_TEMP_2_PIN -1
  #define ORIG_TEMP_BED_PIN 2
  
  #define ORIG_HEATER_0_PIN 4
  #define ORIG_HEATER_1_PIN -1
  #define ORIG_HEATER_2_PIN -1
  #define ORIG_HEATER_BED_PIN 3
  
  #define KILL_PIN -1
  
  #define SDPOWER -1
  #define SDSS -1 // SCL pin of I2C header
  #define LED_PIN -1
  
  #if (GEN7_VERSION >= 13)
  // Gen7 v1.3 removed the fan pin
  #define ORIG_FAN_PIN -1
  #else
  #define ORIG_FAN_PIN 31
  #endif
  #define PS_ON_PIN 15
  
  //All these generations of Gen7 supply thermistor power
  //via PS_ON, so ignore bad thermistor readings
  #define BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE
  
  //our pin for debugging.
  #define DEBUG_PIN 0
  
  //our RS485 pins
  #define TORIG_X_ENABLE_PIN 12
  #define RORIG_X_ENABLE_PIN 13

#endif // SETHI
/****************************************************************************************/



/****************************************************************************************
* 21
* Elefu RA Board
****************************************************************************************/

#if MB(ELEFU_3)
  #define KNOWN_BOARD 1
  
  #ifndef __AVR_ATmega2560__
    #error Oops!  Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
  #endif
  
  
  #define ORIG_X_STEP_PIN        49
  #define ORIG_X_DIR_PIN         13
  #define ORIG_X_ENABLE_PIN      48
  #define ORIG_X_MIN_PIN         35
  #define ORIG_X_MAX_PIN         -1 //34
  
  #define ORIG_Y_STEP_PIN        11
  #define ORIG_Y_DIR_PIN          9
  #define ORIG_Y_ENABLE_PIN      12
  #define ORIG_Y_MIN_PIN         33
  #define ORIG_Y_MAX_PIN         -1 //32
  
  #define ORIG_Z_STEP_PIN         7
  #define ORIG_Z_DIR_PIN          6
  #define ORIG_Z_ENABLE_PIN       8
  #define ORIG_Z_MIN_PIN          31
  #define ORIG_Z_MAX_PIN          -1 //30
  
  #define ORIG_E2_STEP_PIN        43
  #define ORIG_E2_DIR_PIN         47
  #define ORIG_E2_ENABLE_PIN      42
  
  #define ORIG_E1_STEP_PIN        18
  #define ORIG_E1_DIR_PIN         19
  #define ORIG_E1_ENABLE_PIN      38
  
  #define ORIG_E0_STEP_PIN        40
  #define ORIG_E0_DIR_PIN         41
  #define ORIG_E0_ENABLE_PIN      37
  
  #define SDPOWER                 -1
  #define LED_PIN                 -1  //Use +12V Aux port for LED Ring
  
  #define ORIG_FAN_PIN            16 //5V PWM
  
  #define PS_ON_PIN               10 //Set to -1 if using a manual switch on the PWRSW Connector
  #define SLEEP_WAKE_PIN          26 //This feature still needs work
  
  #define ORIG_HEATER_0_PIN       45 //12V PWM1
  #define ORIG_HEATER_1_PIN       46 //12V PWM2
  #define ORIG_HEATER_2_PIN       17 //12V PWM3
  #define ORIG_HEATER_BED_PIN     44 //DOUBLE 12V PWM
  #define ORIG_TEMP_0_PIN          3 //ANALOG NUMBERING
  #define ORIG_TEMP_1_PIN          2 //ANALOG NUMBERING
  #define ORIG_TEMP_2_PIN          1 //ANALOG NUMBERING
  #define ORIG_TEMP_BED_PIN        0 //ANALOG NUMBERING
  
  #define BEEPER 		          36
  
  #define KILL_PIN                -1
  
  // M240  Triggers a camera by emulating a Canon RC-1 Remote
  // Data from: http://www.doc-diy.net/photo/rc-1_hacked/
  #define PHOTOGRAPH_PIN          29
  
  #ifdef RA_CONTROL_PANEL
    #define SDSS             53
    #define SDCARDDETECT     28

    #define BTN_EN1          14
    #define BTN_EN2          39
    #define BTN_ENC          15  //the click

    #define BLEN_C           2
    #define BLEN_B           1
    #define BLEN_A           0

    //encoder rotation values
    #define encrot0          0
    #define encrot1          2
    #define encrot2          3
    #define encrot3          1

  #endif //RA_CONTROL_PANEL
  
  #ifdef RA_DISCO
    //variables for which pins the TLC5947 is using
    #define TLC_CLOCK_PIN    25
    #define TLC_BLANK_PIN    23
    #define TLC_XLAT_PIN     22
    #define TLC_DATA_PIN     24
    
    //We also need to define pin to port number mapping for the 2560 to match the pins listed above. If you change the TLC pins, update this as well per the 2560 datasheet!
    //This currently only works with the RA Board.
    #define TLC_CLOCK_BIT 3 //bit 3 on port A
    #define TLC_CLOCK_PORT &PORTA //bit 3 on port A
    
    #define TLC_BLANK_BIT 1 //bit 1 on port A
    #define TLC_BLANK_PORT &PORTA //bit 1 on port A
    
    #define TLC_DATA_BIT 2 //bit 2 on port A
    #define TLC_DATA_PORT &PORTA //bit 2 on port A
    
    #define TLC_XLAT_BIT 0 //bit 0 on port A
    #define TLC_XLAT_PORT &PORTA //bit 0 on port A
    
    //change this to match your situation. Lots of TLCs takes up the arduino SRAM very quickly, so be careful
    //Leave it at at least 1 if you have enabled RA_LIGHTING
    //The number of TLC5947 boards chained together for use with the animation, additional ones will repeat the animation on them, but are not individually addressable and mimic those before them. You can leave the default at 2 even if you only have 1 TLC5947 module.
    #define NUM_TLCS 2
    
    //These TRANS_ARRAY values let you change the order the LEDs on the lighting modules will animate for chase functions.
    //Modify them according to your specific situation.
    //NOTE: the array should be 8 long for every TLC you have. These defaults assume (2) TLCs.
    #define TRANS_ARRAY {0, 1, 2, 3, 4, 5, 6, 7, 15, 14, 13, 12, 11, 10, 9, 8} //forwards
    //#define TRANS_ARRAY {7, 6, 5, 4, 3, 2, 1, 0, 8, 9, 10, 11, 12, 13, 14, 15} //backwards
  #endif //RA_LIGHTING

#endif // ELEFU_3
/****************************************************************************************/




/****************************************************************************************
* 22
* Gen3  Monolithic Electronics
****************************************************************************************/

#if MB(GEN3_MONOLITHIC)
  #define KNOWN_BOARD 1
  
  #ifndef __AVR_ATmega644P__
    #error Oops!  Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu.
  #endif
  
  #define DEBUG_PIN 0
  
  // x axis
  #define ORIG_X_STEP_PIN 15
  #define ORIG_X_DIR_PIN 18
  #define ORIG_X_MIN_PIN 20
  //Alex Checar #define X_STOP_PIN         20
  #define ORIG_X_ENABLE_PIN 24 //actually uses Y_enable_pin
  #define ORIG_X_MAX_PIN -1
  
  // y axes
  #define ORIG_Y_STEP_PIN 23
  #define ORIG_Y_DIR_PIN 22
  #define ORIG_Y_MIN_PIN 25
  //Alex Checar #define Y_STOP_PIN         25
  #define ORIG_Y_ENABLE_PIN 24 //shared with X_enable_pin
  #define ORIG_Y_MAX_PIN -1
  
  // z axes
  #define ORIG_Z_STEP_PIN 27
  #define ORIG_Z_DIR_PIN 28
  #define ORIG_Z_MIN_PIN 30
  //Alex Checar #define Z_STOP_PIN         30
  #define ORIG_Z_ENABLE_PIN 29
  #define ORIG_Z_MAX_PIN -1
  
  //extruder pins
  #define ORIG_E0_STEP_PIN         12
  #define ORIG_E0_DIR_PIN          17
  #define ORIG_E0_ENABLE_PIN       3
  
  #define ORIG_HEATER_0_PIN 16
  #define ORIG_TEMP_0_PIN 0
  
  #define ORIG_FAN_PIN -1
  
  //bed pins
  #define ORIG_HEATER_BED_PIN -1
  #define ORIG_TEMP_BED_PIN -1
  
  #define SDSS		   -1
  #define SDPOWER          -1
  #define LED_PIN          -1
  
  //pin for controlling the PSU.
  #define PS_ON_PIN       14	//Alex, Do this work on the card?
  
  //Alex extras from Gen3+
  #define KILL_PIN                -1
  #define ORIG_TEMP_1_PIN         -1
  #define ORIG_TEMP_2_PIN         -1
  #define ORIG_HEATER_2_PIN       -1

#endif // GEN3_MONOLITHIC
/****************************************************************************************/



/****************************************************************************************
* 3 
* RAMPS OLD
****************************************************************************************/

#if MB(RAMPS_OLD)
  #define KNOWN_BOARD 1
  
  #if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__)
    #error Oops!  Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
  #endif
  
  // Uncomment the following line for RAMPS v1.0
  //#define RAMPS_V_1_0
  
  #define ORIG_X_STEP_PIN         26
  #define ORIG_X_DIR_PIN          28
  #define ORIG_X_ENABLE_PIN       24
  #define ORIG_X_MIN_PIN           3
  #define ORIG_X_MAX_PIN           2
  
  #define ORIG_Y_STEP_PIN         38
  #define ORIG_Y_DIR_PIN          40
  #define ORIG_Y_ENABLE_PIN       36
  #define ORIG_Y_MIN_PIN          16
  #define ORIG_Y_MAX_PIN          17
  
  #define ORIG_Z_STEP_PIN         44
  #define ORIG_Z_DIR_PIN          46
  #define ORIG_Z_ENABLE_PIN       42
  #define ORIG_Z_MIN_PIN          18
  #define ORIG_Z_MAX_PIN          19
  
  #define ORIG_E0_STEP_PIN        32
  #define ORIG_E0_DIR_PIN         34
  #define ORIG_E0_ENABLE_PIN      30
  
  #define SDPOWER                 48
  #define SDSS                    53
  #define LED_PIN                 13
  #define PS_ON_PIN               -1
  #define KILL_PIN                -1
  
  #ifdef RAMPS_V_1_0 // RAMPS_V_1_0
    #define ORIG_HEATER_0_PIN     12    // RAMPS 1.0
    #define ORIG_HEATER_BED_PIN   -1    // RAMPS 1.0
    #define ORIG_FAN_PIN          11    // RAMPS 1.0
  #else // RAMPS_V_1_1 or RAMPS_V_1_2
    #define ORIG_HEATER_0_PIN     10    // RAMPS 1.1
    #define ORIG_HEATER_BED_PIN    8    // RAMPS 1.1
    #define ORIG_FAN_PIN           9    // RAMPS 1.1
  #endif

  #define ORIG_HEATER_1_PIN       -1
  #define ORIG_HEATER_2_PIN       -1
  #define ORIG_TEMP_0_PIN          2    // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
  #define ORIG_TEMP_1_PIN         -1
  #define ORIG_TEMP_2_PIN         -1
  #define ORIG_TEMP_BED_PIN        1    // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
  
  // SPI for Max6675 Thermocouple
  #ifndef SDSUPPORT
    #define MAX6675_SS       66// Do not use pin 53 if there is even the remote possibility of using Display/SD card
  #else
    #define MAX6675_SS       66// Do not use pin 49 as this is tied to the switch inside the SD card socket to detect if there is an SD card present
  #endif
  
  #ifndef SDSUPPORT
    // these pins are defined in the SD library if building with SD support
    #define SCK_PIN          52
    #define MISO_PIN         50
    #define MOSI_PIN         51
  #endif

#endif // RAMPS_OLD
/****************************************************************************************/




/****************************************************************************************
* 33
* RAMPS 1.3 / 1.4
* RAMPS_13_EFB (Extruder, Fan, Bed)
****************************************************************************************/

#if MB(RAMPS_13_EFB)
  #define KNOWN_BOARD 1
  
  #if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__)
    #error Oops!  Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
  #endif
  
  #define LARGE_FLASH true
  
  //X axis pins
  #define ORIG_X_STEP_PIN         54
  #define ORIG_X_DIR_PIN          55
  #define ORIG_X_ENABLE_PIN       38
  #define ORIG_X_MIN_PIN           3
  #define ORIG_X_MAX_PIN           2
  
  //Y axis pins
  #define ORIG_Y_STEP_PIN         60
  #define ORIG_Y_DIR_PIN          61
  #define ORIG_Y_ENABLE_PIN       56
  #define ORIG_Y_MIN_PIN          14
  #define ORIG_Y_MAX_PIN          15
  
  #define Y2_STEP_PIN             36
  #define Y2_DIR_PIN              34
  #define Y2_ENABLE_PIN           30

  //Z axis pins
  #define ORIG_Z_STEP_PIN         46
  #define ORIG_Z_DIR_PIN          48
  #define ORIG_Z_ENABLE_PIN       62
  #define ORIG_Z_MIN_PIN          18
  #define ORIG_Z_MAX_PIN          19

  #define Z2_STEP_PIN             36
  #define Z2_DIR_PIN              34
  #define Z2_ENABLE_PIN           30

  //E axis pins
  #define ORIG_E0_STEP_PIN        26
  #define ORIG_E0_DIR_PIN         28
  #define ORIG_E0_ENABLE_PIN      24

  #define ORIG_E1_STEP_PIN        36
  #define ORIG_E1_DIR_PIN         34
  #define ORIG_E1_ENABLE_PIN      30
  
  #define SDPOWER                 -1
  #define SDSS                    53
  #define LED_PIN                 13
  
  #define ORIG_FAN_PIN             9
  #define PS_ON_PIN               12
  
  #define ORIG_HEATER_0_PIN       10   // Hotend 1
  #define ORIG_HEATER_1_PIN       -1
  #define ORIG_HEATER_2_PIN       -1
  #define ORIG_HEATER_3_PIN       -1

  #define ORIG_TEMP_0_PIN         13   // ANALOG NUMBERING
  #define ORIG_TEMP_1_PIN         15   // ANALOG NUMBERING
  #define ORIG_TEMP_2_PIN         -1   // ANALOG NUMBERING
  #define ORIG_TEMP_3_PIN         -1   // ANALOG NUMBERING
  
  #define ORIG_HEATER_BED_PIN      8   // BED
  #define ORIG_TEMP_BED_PIN       14   // ANALOG NUMBERING
  
  #ifdef FILAMENT_SENSOR
    // FMM added for Filament Extruder
    //define analog pin for the filament width sensor input
    //Use the RAMPS 1.4 Analog input 5 on the AUX2 connector
    #define FILWIDTH_PIN           5
  #endif
  
  #if defined(REPRAP_DISCOUNT_SMART_CONTROLLER) || defined(G3D_PANEL)
    #define KILL_PIN              41
  #else
    #define KILL_PIN              -1
  #endif
  
  #if NUM_SERVOS > 0
    #define SERVO0_PIN            11
  #endif
  
  #if NUM_SERVOS > 1
    #define SERVO1_PIN             6
  #endif
  
  #if NUM_SERVOS > 2
    #define SERVO2_PIN             5
  #endif
  
  #if NUM_SERVOS > 3
    #define SERVO3_PIN             4
  #endif
    
  #ifdef ULTRA_LCD
    #ifdef NEWPANEL
      #define LCD_PINS_RS         16
      #define LCD_PINS_ENABLE     17
      #define LCD_PINS_D4         23
      #define LCD_PINS_D5         25
      #define LCD_PINS_D6         27
      #define LCD_PINS_D7         29
  
      #ifdef REPRAP_DISCOUNT_SMART_CONTROLLER
        #define BEEPER            37
  
        #define BTN_EN1           31
        #define BTN_EN2           33
        #define BTN_ENC           35
  
        #define SDCARDDETECT      49
      #elif defined(LCD_I2C_PANELOLU2)
        #define BTN_EN1           47  //reverse if the encoder turns the wrong way.
        #define BTN_EN2           43
        #define BTN_ENC           32
        #define LCD_SDSS          53
        #define SDCARDDETECT      -1
        #define KILL_PIN          41
      #elif defined(LCD_I2C_VIKI)
        #define BTN_EN1           22  //reverse if the encoder turns the wrong way.
        #define BTN_EN2            7
        #define BTN_ENC           -1
        #define LCD_SDSS          53
        #define SDCARDDETECT      49
      #else
        //arduino pin which triggers an piezzo beeper
        #define BEEPER            33  // Beeper on AUX-4
  
        //buttons are directly attached using AUX-2
        #ifdef REPRAPWORLD_KEYPAD
          #define BTN_EN1         64 // encoder
          #define BTN_EN2         59 // encoder
          #define BTN_ENC         63 // enter button
          #define SHIFT_OUT       40 // shift register
          #define SHIFT_CLK       44 // shift register
          #define SHIFT_LD        42 // shift register
        #else
          #define BTN_EN1         37
          #define BTN_EN2         35
          #define BTN_ENC         31  //the click
        #endif
  
        #ifdef G3D_PANEL
          #define SDCARDDETECT    49
        #else
          #define SDCARDDETECT    -1  // Ramps does not use this port
        #endif
  
      #endif
  
    #else //old style panel with shift register
      //arduino pin witch triggers an piezzo beeper
      #define BEEPER              33   //No Beeper added
  
      //buttons are attached to a shift register
      // Not wired this yet
      //#define SHIFT_CLK         38
      //#define SHIFT_LD          42
      //#define SHIFT_OUT         40
      //#define SHIFT_EN          17
  
      #define LCD_PINS_RS         16
      #define LCD_PINS_ENABLE     17
      #define LCD_PINS_D4         23
      #define LCD_PINS_D5         25
      #define LCD_PINS_D6         27
      #define LCD_PINS_D7         29
    #endif
  #endif //ULTRA_LCD
  
  // SPI for Max6675 Thermocouple
  #ifndef SDSUPPORT
  // these pins are defined in the SD library if building with SD support
    #define SCK_PIN               52
    #define MISO_PIN              50
    #define MOSI_PIN              51
    #define MAX6675_SS            66 // Do not use pin 53 if there is even the remote possibility of using Display/SD card
  #else
    #define MAX6675_SS            66// Do not use pin 49 as this is tied to the switch inside the SD card socket to detect if there is an SD card present
  #endif

#endif // RAMPS_13_EFB
/****************************************************************************************/




/****************************************************************************************
* 34
* RAMPS 1.3 / 1.4
* RAMPS_13_EEB (Extruder, Extruder, Bed)
****************************************************************************************/

#if MB(RAMPS_13_EEB)
  #define KNOWN_BOARD 1
  
  #if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__)
    #error Oops!  Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
  #endif
  
  #define LARGE_FLASH true
  
    //X axis pins
  #define ORIG_X_STEP_PIN         54
  #define ORIG_X_DIR_PIN          55
  #define ORIG_X_ENABLE_PIN       38
  #define ORIG_X_MIN_PIN           3
  #define ORIG_X_MAX_PIN           2
  
  //Y axis pins
  #define ORIG_Y_STEP_PIN         60
  #define ORIG_Y_DIR_PIN          61
  #define ORIG_Y_ENABLE_PIN       56
  #define ORIG_Y_MIN_PIN          14
  #define ORIG_Y_MAX_PIN          15
  
  #define Y2_STEP_PIN             36
  #define Y2_DIR_PIN              34
  #define Y2_ENABLE_PIN           30

  //Z axis pins
  #define ORIG_Z_STEP_PIN         46
  #define ORIG_Z_DIR_PIN          48
  #define ORIG_Z_ENABLE_PIN       62
  #define ORIG_Z_MIN_PIN          18
  #define ORIG_Z_MAX_PIN          19

  #define Z2_STEP_PIN             36
  #define Z2_DIR_PIN              34
  #define Z2_ENABLE_PIN           30

  //E axis pins
  #define ORIG_E0_STEP_PIN        26
  #define ORIG_E0_DIR_PIN         28
  #define ORIG_E0_ENABLE_PIN      24

  #define ORIG_E1_STEP_PIN        36
  #define ORIG_E1_DIR_PIN         34
  #define ORIG_E1_ENABLE_PIN      30
  
  #define SDPOWER                 -1
  #define SDSS                    53
  #define LED_PIN                 13
  
  #define ORIG_FAN_PIN             4
  #define PS_ON_PIN               12
  
  #define ORIG_HEATER_0_PIN       10   // HOTEND 1
  #define ORIG_HEATER_1_PIN        9   // HOTEND 2
  #define ORIG_HEATER_2_PIN       -1
  #define ORIG_HEATER_3_PIN       -1

  #define ORIG_TEMP_0_PIN         13   // ANALOG NUMBERING
  #define ORIG_TEMP_1_PIN         15   // ANALOG NUMBERING
  #define ORIG_TEMP_2_PIN         -1   // ANALOG NUMBERING
  #define ORIG_TEMP_3_PIN         -1   // ANALOG NUMBERING
  
  #define ORIG_HEATER_BED_PIN      8   // BED
  #define ORIG_TEMP_BED_PIN       14   // ANALOG NUMBERING
  
  #ifdef FILAMENT_SENSOR
    // FMM added for Filament Extruder
    //define analog pin for the filament width sensor input
    //Use the RAMPS 1.4 Analog input 5 on the AUX2 connector
    #define FILWIDTH_PIN           5
  #endif
  
  #if NUM_SERVOS > 0
    #define SERVO0_PIN            11
  #endif
  
  #if NUM_SERVOS > 1
    #define SERVO1_PIN             6
  #endif
  
  #if NUM_SERVOS > 2
    #define SERVO2_PIN             5
  #endif
  
  #if NUM_SERVOS > 3
    #define SERVO3_PIN             4
  #endif
    
  #ifdef ULTRA_LCD
    #ifdef NEWPANEL
      #define LCD_PINS_RS         16
      #define LCD_PINS_ENABLE     17
      #define LCD_PINS_D4         23
      #define LCD_PINS_D5         25
      #define LCD_PINS_D6         27
      #define LCD_PINS_D7         29
  
      #ifdef REPRAP_DISCOUNT_SMART_CONTROLLER
        #define BEEPER            37
  
        #define BTN_EN1           31
        #define BTN_EN2           33
        #define BTN_ENC           35
  
        #define SDCARDDETECT      49
      #elif defined(LCD_I2C_PANELOLU2)
        #define BTN_EN1           47  //reverse if the encoder turns the wrong way.
        #define BTN_EN2           43
        #define BTN_ENC           32
        #define LCD_SDSS          53
        #define SDCARDDETECT      -1
        #define KILL_PIN          41
      #elif defined(LCD_I2C_VIKI)
        #define BTN_EN1           22  //reverse if the encoder turns the wrong way.
        #define BTN_EN2            7
        #define BTN_ENC           -1
        #define LCD_SDSS          53
        #define SDCARDDETECT      49
      #else
        //arduino pin which triggers an piezzo beeper
        #define BEEPER            33  // Beeper on AUX-4
  
        //buttons are directly attached using AUX-2
        #ifdef REPRAPWORLD_KEYPAD
          #define BTN_EN1         64 // encoder
          #define BTN_EN2         59 // encoder
          #define BTN_ENC         63 // enter button
          #define SHIFT_OUT       40 // shift register
          #define SHIFT_CLK       44 // shift register
          #define SHIFT_LD        42 // shift register
        #else
          #define BTN_EN1         37
          #define BTN_EN2         35
          #define BTN_ENC         31  //the click
        #endif
  
        #ifdef G3D_PANEL
          #define SDCARDDETECT    49
        #else
          #define SDCARDDETECT    -1  // Ramps does not use this port
        #endif
  
      #endif
  
    #else //old style panel with shift register
      //arduino pin witch triggers an piezzo beeper
      #define BEEPER              33  //No Beeper added
  
      //buttons are attached to a shift register
      // Not wired this yet
      //#define SHIFT_CLK 38
      //#define SHIFT_LD 42
      //#define SHIFT_OUT 40
      //#define SHIFT_EN 17
  
      #define LCD_PINS_RS         16
      #define LCD_PINS_ENABLE     17
      #define LCD_PINS_D4         23
      #define LCD_PINS_D5         25
      #define LCD_PINS_D6         27
      #define LCD_PINS_D7         29
    #endif
  #endif //ULTRA_LCD
  
  // SPI for Max6675 Thermocouple
  #ifndef SDSUPPORT
  // these pins are defined in the SD library if building with SD support
    #define SCK_PIN               52
    #define MISO_PIN              50
    #define MOSI_PIN              51
    #define MAX6675_SS            66  // Do not use pin 53 if there is even the remote possibility of using Display/SD card
  #else
    #define MAX6675_SS            66  // Do not use pin 49 as this is tied to the switch inside the SD card socket to detect if there is an SD card present
  #endif

#endif // RAMPS_13_EEB
/****************************************************************************************/




/****************************************************************************************
* 35
* RAMPS 1.3 / 1.4
* RAMPS_13_EFF (Extruder, Fan, Fan)
****************************************************************************************/

#if MB(RAMPS_13_EFF)
  #define KNOWN_BOARD 1
  
  #if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__)
    #error Oops!  Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
  #endif
  
  #define LARGE_FLASH true
  
    //X axis pins
  #define ORIG_X_STEP_PIN         54
  #define ORIG_X_DIR_PIN          55
  #define ORIG_X_ENABLE_PIN       38
  #define ORIG_X_MIN_PIN           3
  #define ORIG_X_MAX_PIN           2
  
  //Y axis pins
  #define ORIG_Y_STEP_PIN         60
  #define ORIG_Y_DIR_PIN          61
  #define ORIG_Y_ENABLE_PIN       56
  #define ORIG_Y_MIN_PIN          14
  #define ORIG_Y_MAX_PIN          15
  
  #define Y2_STEP_PIN             36
  #define Y2_DIR_PIN              34
  #define Y2_ENABLE_PIN           30

  //Z axis pins
  #define ORIG_Z_STEP_PIN         46
  #define ORIG_Z_DIR_PIN          48
  #define ORIG_Z_ENABLE_PIN       62
  #define ORIG_Z_MIN_PIN          18
  #define ORIG_Z_MAX_PIN          19

  #define Z2_STEP_PIN             36
  #define Z2_DIR_PIN              34
  #define Z2_ENABLE_PIN           30

  //E axis pins
  #define ORIG_E0_STEP_PIN        26
  #define ORIG_E0_DIR_PIN         28
  #define ORIG_E0_ENABLE_PIN      24

  #define ORIG_E1_STEP_PIN        36
  #define ORIG_E1_DIR_PIN         34
  #define ORIG_E1_ENABLE_PIN      30
  
  #define SDPOWER                 -1
  #define SDSS                    53
  #define LED_PIN                 13
  
  #define ORIG_FAN_PIN             9
  #define PS_ON_PIN               12
  
  #define ORIG_HEATER_0_PIN       10   // HOTEND 1
  #define ORIG_HEATER_1_PIN       -1
  #define ORIG_HEATER_2_PIN       -1
  #define ORIG_HEATER_3_PIN       -1

  #define ORIG_TEMP_0_PIN         13   // ANALOG NUMBERING
  #define ORIG_TEMP_1_PIN         15   // ANALOG NUMBERING
  #define ORIG_TEMP_2_PIN         -1   // ANALOG NUMBERING
  #define ORIG_TEMP_3_PIN         -1   // ANALOG NUMBERING
  
  #define ORIG_HEATER_BED_PIN     -1   // BED
  #define ORIG_TEMP_BED_PIN       14   // ANALOG NUMBERING
  
  #ifdef FILAMENT_SENSOR
    // FMM added for Filament Extruder
    //define analog pin for the filament width sensor input
    //Use the RAMPS 1.4 Analog input 5 on the AUX2 connector
    #define FILWIDTH_PIN           5
  #endif
  
  #if NUM_SERVOS > 0
    #define SERVO0_PIN            11
  #endif
  
  #if NUM_SERVOS > 1
    #define SERVO1_PIN             6
  #endif
  
  #if NUM_SERVOS > 2
    #define SERVO2_PIN             5
  #endif
  
  #if NUM_SERVOS > 3
    #define SERVO3_PIN             4
  #endif
    
  #ifdef ULTRA_LCD
    #ifdef NEWPANEL
      #define LCD_PINS_RS         16
      #define LCD_PINS_ENABLE     17
      #define LCD_PINS_D4         23
      #define LCD_PINS_D5         25
      #define LCD_PINS_D6         27
      #define LCD_PINS_D7         29
  
      #ifdef REPRAP_DISCOUNT_SMART_CONTROLLER
        #define BEEPER            37
  
        #define BTN_EN1           31
        #define BTN_EN2           33
        #define BTN_ENC           35
  
        #define SDCARDDETECT      49
      #elif defined(LCD_I2C_PANELOLU2)
        #define BTN_EN1           47  //reverse if the encoder turns the wrong way.
        #define BTN_EN2           43
        #define BTN_ENC           32
        #define LCD_SDSS          53
        #define SDCARDDETECT      -1
        #define KILL_PIN          41
      #elif defined(LCD_I2C_VIKI)
        #define BTN_EN1           22  //reverse if the encoder turns the wrong way.
        #define BTN_EN2            7
        #define BTN_ENC           -1
        #define LCD_SDSS          53
        #define SDCARDDETECT      49
      #else
        //arduino pin which triggers an piezzo beeper
        #define BEEPER            33  // Beeper on AUX-4
  
        //buttons are directly attached using AUX-2
        #ifdef REPRAPWORLD_KEYPAD
          #define BTN_EN1         64 // encoder
          #define BTN_EN2         59 // encoder
          #define BTN_ENC         63 // enter button
          #define SHIFT_OUT       40 // shift register
          #define SHIFT_CLK       44 // shift register
          #define SHIFT_LD        42 // shift register
        #else
          #define BTN_EN1         37
          #define BTN_EN2         35
          #define BTN_ENC         31  //the click
        #endif
  
        #ifdef G3D_PANEL
          #define SDCARDDETECT    49
        #else
          #define SDCARDDETECT    -1  // Ramps does not use this port
        #endif
  
      #endif
  
    #else //old style panel with shift register
      //arduino pin witch triggers an piezzo beeper
      #define BEEPER              33  //No Beeper added
  
      //buttons are attached to a shift register
      // Not wired this yet
      //#define SHIFT_CLK 38
      //#define SHIFT_LD 42
      //#define SHIFT_OUT 40
      //#define SHIFT_EN 17
  
      #define LCD_PINS_RS         16
      #define LCD_PINS_ENABLE     17
      #define LCD_PINS_D4         23
      #define LCD_PINS_D5         25
      #define LCD_PINS_D6         27
      #define LCD_PINS_D7         29
    #endif
  #endif //ULTRA_LCD
  
  // SPI for Max6675 Thermocouple
  #ifndef SDSUPPORT
  // these pins are defined in the SD library if building with SD support
    #define SCK_PIN               52
    #define MISO_PIN              50
    #define MOSI_PIN              51
    #define MAX6675_SS            66  // Do not use pin 53 if there is even the remote possibility of using Display/SD card
  #else
    #define MAX6675_SS            66  // Do not use pin 49 as this is tied to the switch inside the SD card socket to detect if there is an SD card present
  #endif

#endif // RAMPS_13_EFF
/****************************************************************************************/




/****************************************************************************************
* 36
* RAMPS 1.3 / 1.4
* RAMPS_13_EEF (Extruder, Extruder, Fan)
****************************************************************************************/

#if MB(RAMPS_13_EEF)
  #define KNOWN_BOARD 1
  
  #if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__)
    #error Oops!  Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
  #endif
  
  #define LARGE_FLASH true
  
    //X axis pins
  #define ORIG_X_STEP_PIN         54
  #define ORIG_X_DIR_PIN          55
  #define ORIG_X_ENABLE_PIN       38
  #define ORIG_X_MIN_PIN           3
  #define ORIG_X_MAX_PIN           2
  
  //Y axis pins
  #define ORIG_Y_STEP_PIN         60
  #define ORIG_Y_DIR_PIN          61
  #define ORIG_Y_ENABLE_PIN       56
  #define ORIG_Y_MIN_PIN          14
  #define ORIG_Y_MAX_PIN          15
  
  #define Y2_STEP_PIN             36
  #define Y2_DIR_PIN              34
  #define Y2_ENABLE_PIN           30

  //Z axis pins
  #define ORIG_Z_STEP_PIN         46
  #define ORIG_Z_DIR_PIN          48
  #define ORIG_Z_ENABLE_PIN       62
  #define ORIG_Z_MIN_PIN          18
  #define ORIG_Z_MAX_PIN          19

  #define Z2_STEP_PIN             36
  #define Z2_DIR_PIN              34
  #define Z2_ENABLE_PIN           30

  //E axis pins
  #define ORIG_E0_STEP_PIN        26
  #define ORIG_E0_DIR_PIN         28
  #define ORIG_E0_ENABLE_PIN      24

  #define ORIG_E1_STEP_PIN        36
  #define ORIG_E1_DIR_PIN         34
  #define ORIG_E1_ENABLE_PIN      30
  
  #define SDPOWER                 -1
  #define SDSS                    53
  #define LED_PIN                 13
  
  #define ORIG_FAN_PIN             8
  #define PS_ON_PIN               12
  
  #define ORIG_HEATER_0_PIN       10   // HOTEND 1
  #define ORIG_HEATER_1_PIN        9   // HOTEND 2
  #define ORIG_HEATER_2_PIN       -1
  #define ORIG_HEATER_3_PIN       -1

  #define ORIG_TEMP_0_PIN         13   // ANALOG NUMBERING
  #define ORIG_TEMP_1_PIN         15   // ANALOG NUMBERING
  #define ORIG_TEMP_2_PIN         -1   // ANALOG NUMBERING
  #define ORIG_TEMP_3_PIN         -1   // ANALOG NUMBERING
  
  #define ORIG_HEATER_BED_PIN      8   // BED
  #define ORIG_TEMP_BED_PIN       14   // ANALOG NUMBERING
  
  #ifdef FILAMENT_SENSOR
    // FMM added for Filament Extruder
    //define analog pin for the filament width sensor input
    //Use the RAMPS 1.4 Analog input 5 on the AUX2 connector
    #define FILWIDTH_PIN           5
  #endif
  
  #if NUM_SERVOS > 0
    #define SERVO0_PIN            11
  #endif
  
  #if NUM_SERVOS > 1
    #define SERVO1_PIN             6
  #endif
  
  #if NUM_SERVOS > 2
    #define SERVO2_PIN             5
  #endif
  
  #if NUM_SERVOS > 3
    #define SERVO3_PIN             4
  #endif
    
  #ifdef ULTRA_LCD
    #ifdef NEWPANEL
      #define LCD_PINS_RS         16
      #define LCD_PINS_ENABLE     17
      #define LCD_PINS_D4         23
      #define LCD_PINS_D5         25
      #define LCD_PINS_D6         27
      #define LCD_PINS_D7         29
  
      #ifdef REPRAP_DISCOUNT_SMART_CONTROLLER
        #define BEEPER            37
  
        #define BTN_EN1           31
        #define BTN_EN2           33
        #define BTN_ENC           35
  
        #define SDCARDDETECT      49
      #elif defined(LCD_I2C_PANELOLU2)
        #define BTN_EN1           47  //reverse if the encoder turns the wrong way.
        #define BTN_EN2           43
        #define BTN_ENC           32
        #define LCD_SDSS          53
        #define SDCARDDETECT      -1
        #define KILL_PIN          41
      #elif defined(LCD_I2C_VIKI)
        #define BTN_EN1           22  //reverse if the encoder turns the wrong way.
        #define BTN_EN2            7
        #define BTN_ENC           -1
        #define LCD_SDSS          53
        #define SDCARDDETECT      49
      #else
        //arduino pin which triggers an piezzo beeper
        #define BEEPER            33  // Beeper on AUX-4
  
        //buttons are directly attached using AUX-2
        #ifdef REPRAPWORLD_KEYPAD
          #define BTN_EN1         64 // encoder
          #define BTN_EN2         59 // encoder
          #define BTN_ENC         63 // enter button
          #define SHIFT_OUT       40 // shift register
          #define SHIFT_CLK       44 // shift register
          #define SHIFT_LD        42 // shift register
        #else
          #define BTN_EN1         37
          #define BTN_EN2         35
          #define BTN_ENC         31  //the click
        #endif
  
        #ifdef G3D_PANEL
          #define SDCARDDETECT    49
        #else
          #define SDCARDDETECT    -1  // Ramps does not use this port
        #endif
  
      #endif
  
    #else //old style panel with shift register
      //arduino pin witch triggers an piezzo beeper
      #define BEEPER              33  //No Beeper added
  
      //buttons are attached to a shift register
      // Not wired this yet
      //#define SHIFT_CLK 38
      //#define SHIFT_LD 42
      //#define SHIFT_OUT 40
      //#define SHIFT_EN 17
  
      #define LCD_PINS_RS         16
      #define LCD_PINS_ENABLE     17
      #define LCD_PINS_D4         23
      #define LCD_PINS_D5         25
      #define LCD_PINS_D6         27
      #define LCD_PINS_D7         29
    #endif
  #endif //ULTRA_LCD
  
  // SPI for Max6675 Thermocouple
  #ifndef SDSUPPORT
  // these pins are defined in the SD library if building with SD support
    #define SCK_PIN               52
    #define MISO_PIN              50
    #define MOSI_PIN              51
    #define MAX6675_SS            66  // Do not use pin 53 if there is even the remote possibility of using Display/SD card
  #else
    #define MAX6675_SS            66  // Do not use pin 49 as this is tied to the switch inside the SD card socket to detect if there is an SD card present
  #endif

#endif // RAMPS_13_EEF
/****************************************************************************************/




/****************************************************************************************
* 301
* Rambo
****************************************************************************************/

#if MB(RAMBO)
#define KNOWN_BOARD

#ifndef __AVR_ATmega2560__
#error Oops!  Make sure you have 'Arduino Mega 2560' selected from the 'Tools -> Boards' menu.
#endif

#define LARGE_FLASH true

#define ORIG_X_STEP_PIN 37
#define ORIG_X_DIR_PIN 48
#define ORIG_X_MIN_PIN 12
#define ORIG_X_MAX_PIN 24
#define ORIG_X_ENABLE_PIN 29
#define X_MS1_PIN 40
#define X_MS2_PIN 41

#define ORIG_Y_STEP_PIN 36
#define ORIG_Y_DIR_PIN 49
#define ORIG_Y_MIN_PIN 11
#define ORIG_Y_MAX_PIN 23
#define ORIG_Y_ENABLE_PIN 28
#define Y_MS1_PIN 69
#define Y_MS2_PIN 39

#define ORIG_Z_STEP_PIN 35
#define ORIG_Z_DIR_PIN 47
#define ORIG_Z_MIN_PIN 10
#define ORIG_Z_MAX_PIN 30
#define ORIG_Z_ENABLE_PIN 27
#define Z_MS1_PIN 68
#define Z_MS2_PIN 67

#define ORIG_HEATER_BED_PIN 3
#define ORIG_TEMP_BED_PIN 2

#define ORIG_HEATER_0_PIN  9
#define ORIG_TEMP_0_PIN 0

#define ORIG_HEATER_1_PIN 7
#define ORIG_TEMP_1_PIN 1

#ifdef BARICUDA
#define ORIG_HEATER_2_PIN 6
#else
#define ORIG_HEATER_2_PIN -1
#endif
#define ORIG_TEMP_2_PIN -1

#define ORIG_E0_STEP_PIN         34
#define ORIG_E0_DIR_PIN          43
#define ORIG_E0_ENABLE_PIN       26
#define E0_MS1_PIN 65
#define E0_MS2_PIN 66

#define ORIG_E1_STEP_PIN         33
#define ORIG_E1_DIR_PIN          42
#define ORIG_E1_ENABLE_PIN       25
#define E1_MS1_PIN 63
#define E1_MS2_PIN 64

#define DIGIPOTSS_PIN 38
#define DIGIPOT_CHANNELS {4,5,3,0,1} // X Y Z E0 E1 digipot channels to stepper driver mapping

#define SDPOWER            -1
#define SDSS               53
#define LED_PIN            13
#define ORIG_FAN_PIN        8
#define PS_ON_PIN           4
#define KILL_PIN           -1 //80 with Smart Controller LCD
#define SUICIDE_PIN        -1  //PIN that has to be turned on right after start, to keep power flowing.

#ifdef ULTRA_LCD
  #define KILL_PIN 80
  #ifdef NEWPANEL
   //arduino pin which triggers an piezzo beeper
    #define BEEPER 79      // Beeper on AUX-4
    #define LCD_PINS_RS 70
    #define LCD_PINS_ENABLE 71
    #define LCD_PINS_D4 72
    #define LCD_PINS_D5 73
    #define LCD_PINS_D6 74
    #define LCD_PINS_D7 75

    //buttons are directly attached using AUX-2
    #define BTN_EN1 76
    #define BTN_EN2 77
    #define BTN_ENC 78  //the click

    #define BLEN_C 2
    #define BLEN_B 1
    #define BLEN_A 0

    #define SDCARDDETECT 81    // Ramps does not use this port

    //encoder rotation values
    #define encrot0 0
    #define encrot1 2
    #define encrot2 3
    #define encrot3 1
  #else //old style panel with shift register
    //arduino pin witch triggers an piezzo beeper
    #define BEEPER 33    No Beeper added
    //buttons are attached to a shift register
    // Not wired this yet
    // #define SHIFT_CLK 38
    // #define SHIFT_LD 42
    // #define SHIFT_OUT 40
    // #define SHIFT_EN 17

    #define LCD_PINS_RS 75
    #define LCD_PINS_ENABLE 17
    #define LCD_PINS_D4 23
    #define LCD_PINS_D5 25
    #define LCD_PINS_D6 27
    #define LCD_PINS_D7 29

    //encoder rotation values
    #define encrot0 0
    #define encrot1 2
    #define encrot2 3
    #define encrot3 1

    //bits in the shift register that carry the buttons for:
    // left up center down right red
    #define BL_LE 7
    #define BL_UP 6
    #define BL_MI 5
    #define BL_DW 4
    #define BL_RI 3
    #define BL_ST 2
    #define BLEN_B 1
    #define BLEN_A 0
  #endif
#endif //ULTRA_LCD

#ifdef FILAMENT_SENSOR
  //Filip added pin for Filament sensor analog input 
  #define FILWIDTH_PIN        3
#endif //FILAMENT_SENSOR

#endif // RAMBO
/****************************************************************************************/



/****************************************************************************************
* 4
* Duemilanove w/ ATMega328P
****************************************************************************************/

#if MB(DUEMILANOVE_328P)
#define KNOWN_BOARD 1

#ifndef __AVR_ATmega328P__
#error Oops!  Make sure you have 'Arduino Duemilanove w/ ATMega328' selected from the 'Tools -> Boards' menu.
#endif

#define ORIG_X_STEP_PIN         19
#define ORIG_X_DIR_PIN          18
#define ORIG_X_ENABLE_PIN       -1
#define X_STOP_PIN              17

#define ORIG_Y_STEP_PIN         10
#define ORIG_Y_DIR_PIN           7
#define ORIG_Y_ENABLE_PIN       -1
#define Y_STOP_PIN               8

#define ORIG_Z_STEP_PIN         13
#define ORIG_Z_DIR_PIN           3
#define ORIG_Z_ENABLE_PIN        2
#define Z_STOP_PIN               4

#define ORIG_E0_STEP_PIN         11
#define ORIG_E0_DIR_PIN          12
#define ORIG_E0_ENABLE_PIN       -1

#define SDPOWER          -1
#define SDSS          -1
#define LED_PIN            -1
#define ORIG_FAN_PIN             5
#define PS_ON_PIN          -1
#define KILL_PIN           -1

#define ORIG_HEATER_0_PIN        6
#define ORIG_HEATER_1_PIN        -1
#define ORIG_HEATER_2_PIN        -1
#define ORIG_TEMP_0_PIN          0    // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
#define ORIG_TEMP_1_PIN          -1
#define ORIG_TEMP_2_PIN          -1
#define ORIG_HEATER_BED_PIN      -1
#define ORIG_TEMP_BED_PIN        -1

#endif // DUEMILANOVE_328P
/****************************************************************************************/



/****************************************************************************************
* 5 - 51
* Gen6 - Gen6 Deluxe
****************************************************************************************/

#if MB(GEN6) || MB(GEN6_DELUXE)
#define KNOWN_BOARD 1

#ifndef __AVR_ATmega644P__
#ifndef __AVR_ATmega1284P__
#error Oops!  Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu.
#endif
#endif

//x axis pins
    #define ORIG_X_STEP_PIN      15
    #define ORIG_X_DIR_PIN       18
    #define ORIG_X_ENABLE_PIN    19
    #define X_STOP_PIN      20

    //y axis pins
    #define ORIG_Y_STEP_PIN      23
    #define ORIG_Y_DIR_PIN       22
    #define ORIG_Y_ENABLE_PIN    24
    #define Y_STOP_PIN      25

    //z axis pins
    #define ORIG_Z_STEP_PIN      27
    #define ORIG_Z_DIR_PIN       28
    #define ORIG_Z_ENABLE_PIN    29
    #define Z_STOP_PIN      30

    //extruder pins
    #define ORIG_E0_STEP_PIN      4    //Edited @ EJE Electronics 20100715
    #define ORIG_E0_DIR_PIN       2    //Edited @ EJE Electronics 20100715
    #define ORIG_E0_ENABLE_PIN    3    //Added @ EJE Electronics 20100715
    #define ORIG_TEMP_0_PIN      5     //changed @ rkoeppl 20110410
    #define ORIG_TEMP_1_PIN      -1    //changed @ rkoeppl 20110410


    #define ORIG_TEMP_2_PIN      -1    //changed @ rkoeppl 20110410
    #define ORIG_HEATER_0_PIN    14    //changed @ rkoeppl 20110410
    #define ORIG_HEATER_1_PIN    -1
    #define ORIG_HEATER_2_PIN    -1
    #if MOTHERBOARD == 5
    #define ORIG_HEATER_BED_PIN  -1    //changed @ rkoeppl 20110410
    #define ORIG_TEMP_BED_PIN    -1    //changed @ rkoeppl 20110410
    #else
    #define ORIG_HEATER_BED_PIN   1    //changed @ rkoeppl 20110410
    #define ORIG_TEMP_BED_PIN     0    //changed @ rkoeppl 20110410
    #endif
    #define SDPOWER          -1
    #define SDSS          17
    #define LED_PIN         -1    //changed @ rkoeppl 20110410
    #define ORIG_FAN_PIN         -1    //changed @ rkoeppl 20110410
    #define PS_ON_PIN       -1    //changed @ rkoeppl 20110410
    #define KILL_PIN        -1    //changed @ drakelive 20120830
    //our pin for debugging.

    #define DEBUG_PIN        0

    //our RS485 pins
    #define TX_ENABLE_PIN 12
    #define RX_ENABLE_PIN 13

#endif // GEN6 || GEN6_DELUXE
/****************************************************************************************/



/****************************************************************************************
* 6 - 62 - 63 - 64 - 65
*  6 - Sanguinololu <1.2
* 62 - Sanguinololu 1.2 and above
* 63 - Melzi
* 64 - STB 1.1
* 65 - Azteeg X1
****************************************************************************************/

#if MB(STB_11)
  #define STB
#endif

#if MB(MELZI) || MB(MELZI_1284)
  #define MELZI
#endif

#if MB(AZTEEG_X1)
  #define AZTEEG_X1
#endif

#if MB(SANGUINOLOLU_12) || MB(MELZI) || MB(STB_11) || MB(AZTEEG_X1) || MB(MELZI_1284)
  #undef MOTHERBOARD
  #define MOTHERBOARD BOARD_SANGUINOLOLU_11
  #define SANGUINOLOLU_V_1_2

  #if defined(__AVR_ATmega1284P__)
    #define LARGE_FLASH true
  #endif
#endif

#if MB(SANGUINOLOLU_11)
#define KNOWN_BOARD 1
#ifndef __AVR_ATmega644P__
#ifndef __AVR_ATmega1284P__
#error Oops!  Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu.
#endif
#endif

#define ORIG_X_STEP_PIN         15
#define ORIG_X_DIR_PIN          21
#define X_STOP_PIN         18

#define ORIG_Y_STEP_PIN         22
#define ORIG_Y_DIR_PIN          23
#define Y_STOP_PIN         19

#define ORIG_Z_STEP_PIN         3
#define ORIG_Z_DIR_PIN          2
#define Z_STOP_PIN         20

#define ORIG_E0_STEP_PIN         1
#define ORIG_E0_DIR_PIN          0

#define LED_PIN            -1

#define ORIG_FAN_PIN            -1
 #if ORIG_FAN_PIN == 12 || ORIG_FAN_PIN ==13
  #define FAN_SOFT_PWM
#endif

#ifdef MELZI
 #define LED_PIN            27 /* On some broken versions of the Sanguino libraries the pin definitions are wrong, which then needs LED_PIN as pin 28. But you better upgrade your Sanguino libraries! See #368. */
 #define ORIG_FAN_PIN            4 // Works for Panelolu2 too
#endif

#ifdef STB
 #define ORIG_FAN_PIN            4
	//  Uncomment this if you have the first generation (V1.10) of STBs board
 #define LCD_PIN_BL         17 // LCD backlight LED
#endif

#ifdef AZTEEG_X1
 #define ORIG_FAN_PIN            4
#endif

#if NUM_SERVOS > 0
  #define SERVO0_PIN          -1
#endif

#if NUM_SERVOS > 1
  #define SERVO1_PIN        -1
#endif

#if NUM_SERVOS > 2
  #define SERVO2_PIN        -1
#endif

#if NUM_SERVOS > 3
  #define SERVO3_PIN        -1
#endif

#define PS_ON_PIN          -1
#define KILL_PIN           -1

#define ORIG_HEATER_0_PIN       13 // (extruder)
#define ORIG_HEATER_1_PIN       -1
#define ORIG_HEATER_2_PIN       -1

#ifdef SANGUINOLOLU_V_1_2

 #define ORIG_HEATER_BED_PIN     12 // (bed)
 #define ORIG_X_ENABLE_PIN       14
 #define ORIG_Y_ENABLE_PIN       14
 #define ORIG_Z_ENABLE_PIN       26
 #define ORIG_E0_ENABLE_PIN      14

 #ifdef LCD_I2C_PANELOLU2
   #define ORIG_FAN_PIN          4 // Uses Transistor1 (PWM) on Panelolu2's Sanguino Adapter Board to drive the fan
 #endif

#else

#define ORIG_HEATER_BED_PIN      14  // (bed)
#define ORIG_X_ENABLE_PIN       -1
#define ORIG_Y_ENABLE_PIN       -1
#define ORIG_Z_ENABLE_PIN       -1
#define ORIG_E0_ENABLE_PIN      -1

#endif

#define ORIG_TEMP_0_PIN          7   // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 33 extruder)
#define ORIG_TEMP_1_PIN         -1
#define ORIG_TEMP_2_PIN         -1
#define ORIG_TEMP_BED_PIN        6   // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 34 bed)
#define SDPOWER            -1
#define SDSS               31

/* On some broken versions of the Sanguino libraries the pin definitions are wrong, which then needs SDSS as pin 24. But you better upgrade your Sanguino libraries! See #368. */
//#define SDSS               24

 #ifdef ULTRA_LCD
   #ifdef NEWPANEL
     //we have no buzzer installed
     #define BEEPER -1
     //LCD Pins
     #ifdef DOGLCD
	   #ifdef U8GLIB_ST7920 //SPI GLCD 12864 ST7920 ( like [www.digole.com] ) For Melzi V2.0
	  	 #define LCD_PINS_RS 30 //CS chip select /SS chip slave select
	  	 #define LCD_PINS_ENABLE 29 //SID (MOSI)
	  	 #define LCD_PINS_D4 17 //SCK (CLK) clock
	  	 #define BEEPER 27 // Pin 27 is take by LED_Pin, but Melzi LED do nothing with Marlin and I take this pin for BEEPER.... See here > [github.com] , If you want use this pin with Gcode M42 instead BEEPER
	   #else
	  	 // Pins for DOGM SPI LCD Support
	  	 #define DOGLCD_A0 30
	  	 #define DOGLCD_CS 29
	  	 #define LCD_CONTRAST 1
	   #endif
       // Uncomment screen orientation
       #define LCD_SCREEN_ROT_0
         // #define LCD_SCREEN_ROT_90
         // #define LCD_SCREEN_ROT_180
         // #define LCD_SCREEN_ROT_270
       #else // standard Hitachi LCD controller
       #define LCD_PINS_RS        4
       #define LCD_PINS_ENABLE    17
       #define LCD_PINS_D4        30
       #define LCD_PINS_D5        29
       #define LCD_PINS_D6        28
       #define LCD_PINS_D7        27
     #endif
     //The encoder and click button
     #define BTN_EN1 11
     #define BTN_EN2 10
     #ifdef LCD_I2C_PANELOLU2
       #ifdef MELZI
         #define BTN_ENC 29 //the click switch
         #define LCD_SDSS 30 //to use the SD card reader on the Panelolu2 rather than the melzi board
       #else
         #define BTN_ENC 30 //the click switch
       #endif
     #else
       #define BTN_ENC 16  //the click switch
       #define LCD_SDSS 28 //to use the SD card reader on the smart controller rather than the melzi board
     #endif //Panelolu2
     //not connected to a pin
     #define SDCARDDETECT -1

   #endif //Newpanel
 #endif //Ultipanel

 #ifdef MAKRPANEL
     #define BEEPER 29
     // Pins for DOGM SPI LCD Support
     #define DOGLCD_A0  30
     #define DOGLCD_CS  17
     #define LCD_PIN_BL 28  // backlight LED on PA3
     // GLCD features
     #define LCD_CONTRAST 1
     // Uncomment screen orientation
     #define LCD_SCREEN_ROT_0
       // #define LCD_SCREEN_ROT_90
       // #define LCD_SCREEN_ROT_180
       // #define LCD_SCREEN_ROT_270
     //The encoder and click button
     #define BTN_EN1 11
     #define BTN_EN2 10
     #define BTN_ENC 16  //the click switch
     //not connected to a pin
     #define SDCARDDETECT -1
 #endif //Makrpanel

#endif // SANGUINOLOLU_11
/****************************************************************************************/



/****************************************************************************************
* 67
* AZTEEG X3
****************************************************************************************/

#if MB(AZTEEG_X3)
#define KNOWN_BOARD 1

#if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__)
  #error Oops!  Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
#endif

#define LARGE_FLASH true

#define ORIG_X_STEP_PIN         54
#define ORIG_X_DIR_PIN          55
#define ORIG_X_ENABLE_PIN       38
#define ORIG_X_MIN_PIN           3
#define ORIG_X_MAX_PIN           2

#define ORIG_Y_STEP_PIN         60
#define ORIG_Y_DIR_PIN          61
#define ORIG_Y_ENABLE_PIN       56
#define ORIG_Y_MIN_PIN          14
#define ORIG_Y_MAX_PIN          15

#define ORIG_Z_STEP_PIN         46
#define ORIG_Z_DIR_PIN          48
#define ORIG_Z_ENABLE_PIN       62
#define ORIG_Z_MIN_PIN          18
#define ORIG_Z_MAX_PIN          19

#define Y2_STEP_PIN             36
#define Y2_DIR_PIN              34
#define Y2_ENABLE_PIN           30

#define Z2_STEP_PIN             36
#define Z2_DIR_PIN              34
#define Z2_ENABLE_PIN           30

#define ORIG_E0_STEP_PIN        26
#define ORIG_E0_DIR_PIN         28
#define ORIG_E0_ENABLE_PIN      24

#define ORIG_E1_STEP_PIN        36
#define ORIG_E1_DIR_PIN         34
#define ORIG_E1_ENABLE_PIN      30

#define SDPOWER                 -1
#define SDSS                    53
#define LED_PIN                 13

#define ORIG_FAN_PIN             9
#define PS_ON_PIN               12

#if defined(REPRAP_DISCOUNT_SMART_CONTROLLER) || defined(G3D_PANEL)
  #define KILL_PIN              41
#else
  #define KILL_PIN              -1
#endif

#define ORIG_HEATER_0_PIN       10   // HOTEND 1
#define ORIG_HEATER_1_PIN       -1
#define ORIG_HEATER_2_PIN       -1
#define ORIG_HEATER_3_PIN       -1

#define ORIG_TEMP_0_PIN         13   // ANALOG NUMBERING
#define ORIG_TEMP_1_PIN         15   // ANALOG NUMBERING
#define ORIG_TEMP_2_PIN         -1   // ANALOG NUMBERING

#define ORIG_HEATER_BED_PIN      8   // BED

#define ORIG_TEMP_BED_PIN       14   // ANALOG NUMBERING

#if NUM_SERVOS > 0
  #define SERVO0_PIN              11
#endif

#if NUM_SERVOS > 1
  #define SERVO1_PIN               6
#endif

#if NUM_SERVOS > 2
  #define SERVO2_PIN               5
#endif

#if NUM_SERVOS > 3
  #define SERVO3_PIN               4
#endif
  
#ifdef TEMP_STAT_LEDS
  #define STAT_LED_RED       6
  #define STAT_LED_BLUE     11
#endif

#ifdef ULTRA_LCD

  #ifdef NEWPANEL
    #define LCD_PINS_RS 16
    #define LCD_PINS_ENABLE 17
    #define LCD_PINS_D4 23
    #define LCD_PINS_D5 25
    #define LCD_PINS_D6 27
    #define LCD_PINS_D7 29

    #ifdef REPRAP_DISCOUNT_SMART_CONTROLLER
      #define BEEPER 37

      #define BTN_EN1 31
      #define BTN_EN2 33
      #define BTN_ENC 35

      #define SDCARDDETECT 49
    #elif defined(LCD_I2C_PANELOLU2)
      #define BTN_EN1 47  //reverse if the encoder turns the wrong way.
      #define BTN_EN2 43
      #define BTN_ENC 32
      #define LCD_SDSS 53
      #define SDCARDDETECT -1
      #define KILL_PIN 41
    #elif defined(LCD_I2C_VIKI)
      #define BTN_EN1 22  //reverse if the encoder turns the wrong way.
      #define BTN_EN2 7
      #define BTN_ENC -1
      #define LCD_SDSS 53
      #define SDCARDDETECT 49
    #else
      //arduino pin which triggers an piezzo beeper
      #define BEEPER 33  // Beeper on AUX-4

      //buttons are directly attached using AUX-2
      #ifdef REPRAPWORLD_KEYPAD
        #define BTN_EN1 64 // encoder
        #define BTN_EN2 59 // encoder
        #define BTN_ENC 63 // enter button
        #define SHIFT_OUT 40 // shift register
        #define SHIFT_CLK 44 // shift register
        #define SHIFT_LD 42 // shift register
      #else
        #define BTN_EN1 37
        #define BTN_EN2 35
        #define BTN_ENC 31  //the click
      #endif

      #ifdef G3D_PANEL
        #define SDCARDDETECT 49
      #else
        #define SDCARDDETECT -1  // Ramps does not use this port
      #endif

    #endif

  #else //old style panel with shift register
    //arduino pin witch triggers an piezzo beeper
    #define BEEPER 33   //No Beeper added

    //buttons are attached to a shift register
    // Not wired this yet
    //#define SHIFT_CLK 38
    //#define SHIFT_LD 42
    //#define SHIFT_OUT 40
    //#define SHIFT_EN 17

    #define LCD_PINS_RS 16
    #define LCD_PINS_ENABLE 17
    #define LCD_PINS_D4 23
    #define LCD_PINS_D5 25
    #define LCD_PINS_D6 27
    #define LCD_PINS_D7 29
  #endif

#endif //ULTRA_LCD

// SPI for Max6675 Thermocouple

#ifndef SDSUPPORT
// these pins are defined in the SD library if building with SD support
  #define SCK_PIN          52
  #define MISO_PIN         50
  #define MOSI_PIN         51
  #define MAX6675_SS       66// Do not use pin 53 if there is even the remote possibility of using Display/SD card
#else
  #define MAX6675_SS       66// Do not use pin 49 as this is tied to the switch inside the SD card socket to detect if there is an SD card present
#endif

#endif // AZTEEG X3
/****************************************************************************************/



/****************************************************************************************
* 68 
* AZTEEG X3 PRO
****************************************************************************************/

#if MB(AZTEEG_X3_PRO)
#define KNOWN_BOARD 1

#if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__)
  #error Oops!  Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
#endif

#define LARGE_FLASH true

#define LARGE_FLASH true

#define ORIG_X_STEP_PIN         54
#define ORIG_X_DIR_PIN          55
#define ORIG_X_ENABLE_PIN       38
#define ORIG_X_MIN_PIN           3
#define ORIG_X_MAX_PIN           2

#define ORIG_Y_STEP_PIN         60
#define ORIG_Y_DIR_PIN          61
#define ORIG_Y_ENABLE_PIN       56
#define ORIG_Y_MIN_PIN          14
#define ORIG_Y_MAX_PIN          15

#define ORIG_Z_STEP_PIN         46
#define ORIG_Z_DIR_PIN          48
#define ORIG_Z_ENABLE_PIN       62
#define ORIG_Z_MIN_PIN          18
#define ORIG_Z_MAX_PIN          19

#define Y2_STEP_PIN             36
#define Y2_DIR_PIN              34
#define Y2_ENABLE_PIN           30

#define Z2_STEP_PIN             36
#define Z2_DIR_PIN              34
#define Z2_ENABLE_PIN           30

#define ORIG_E0_STEP_PIN        26
#define ORIG_E0_DIR_PIN         28
#define ORIG_E0_ENABLE_PIN      24

#define ORIG_E1_STEP_PIN        36
#define ORIG_E1_DIR_PIN         34
#define ORIG_E1_ENABLE_PIN      30

#define ORIG_E2_STEP_PIN        23
#define ORIG_E2_DIR_PIN         25
#define ORIG_E2_ENABLE_PIN      40

#define ORIG_E3_STEP_PIN        27
#define ORIG_E3_DIR_PIN         29
#define ORIG_E3_ENABLE_PIN      41

#define SDPOWER                 -1
#define SDSS                    53
#define LED_PIN                 13

#define ORIG_FAN_PIN             9
#define PS_ON_PIN               12

#if defined(REPRAP_DISCOUNT_SMART_CONTROLLER) || defined(G3D_PANEL)
  #define KILL_PIN              41
#else
  #define KILL_PIN              -1
#endif

#define ORIG_HEATER_0_PIN       10   // HOTEND 1
#define ORIG_HEATER_1_PIN        9   // HOTEND 2
#define ORIG_HEATER_2_PIN       16   // HOTEND 3
#define ORIG_HEATER_3_PIN       17   // HOTEND 4

#define ORIG_TEMP_0_PIN         13   // ANALOG NUMBERING
#define ORIG_TEMP_1_PIN         15   // ANALOG NUMBERING
#define ORIG_TEMP_2_PIN         12   // ANALOG NUMBERING
#define ORIG_TEMP_3_PIN         11   // ANALOG NUMBERING

#define TC1                      4   // ANALOG NUMBERING Thermo couple on Azteeg X3Pro
#define TC2                      5   // ANALOG NUMBERING Thermo couple on Azteeg X3Pro

#define ORIG_HEATER_BED_PIN      8   // BED

#define ORIG_TEMP_BED_PIN       14   // ANALOG NUMBERING

#if NUM_SERVOS > 0
  #define SERVO0_PIN              11
#endif

#if NUM_SERVOS > 1
  #define SERVO1_PIN               6
#endif

#if NUM_SERVOS > 2
  #define SERVO2_PIN               5
#endif

#if NUM_SERVOS > 3
  #define SERVO3_PIN               4
#endif
  
#ifdef TEMP_STAT_LEDS
  #define STAT_LED_RED       6
  #define STAT_LED_BLUE     11
#endif

#ifdef ULTRA_LCD

  #ifdef NEWPANEL
    #define LCD_PINS_RS 16
    #define LCD_PINS_ENABLE 17
    #define LCD_PINS_D4 23
    #define LCD_PINS_D5 25
    #define LCD_PINS_D6 27
    #define LCD_PINS_D7 29

    #ifdef REPRAP_DISCOUNT_SMART_CONTROLLER
      #define BEEPER 37

      #define BTN_EN1 31
      #define BTN_EN2 33
      #define BTN_ENC 35

      #define SDCARDDETECT 49
    #elif defined(LCD_I2C_PANELOLU2)
      #define BTN_EN1 47  //reverse if the encoder turns the wrong way.
      #define BTN_EN2 43
      #define BTN_ENC 32
      #define LCD_SDSS 53
      #define SDCARDDETECT -1
      #define KILL_PIN 41
    #elif defined(LCD_I2C_VIKI)
      #define BTN_EN1 22  //reverse if the encoder turns the wrong way.
      #define BTN_EN2 7
      #define BTN_ENC -1
      #define LCD_SDSS 53
      #define SDCARDDETECT 49
    #else
      //arduino pin which triggers an piezzo beeper
      #define BEEPER 33  // Beeper on AUX-4

      //buttons are directly attached using AUX-2
      #ifdef REPRAPWORLD_KEYPAD
        #define BTN_EN1 64 // encoder
        #define BTN_EN2 59 // encoder
        #define BTN_ENC 63 // enter button
        #define SHIFT_OUT 40 // shift register
        #define SHIFT_CLK 44 // shift register
        #define SHIFT_LD 42 // shift register
      #else
        #define BTN_EN1 37
        #define BTN_EN2 35
        #define BTN_ENC 31  //the click
      #endif

      #ifdef G3D_PANEL
        #define SDCARDDETECT 49
      #else
        #define SDCARDDETECT -1  // Ramps does not use this port
      #endif

    #endif

  #else //old style panel with shift register
    //arduino pin witch triggers an piezzo beeper
    #define BEEPER 33   //No Beeper added

    //buttons are attached to a shift register
    // Not wired this yet
    //#define SHIFT_CLK 38
    //#define SHIFT_LD 42
    //#define SHIFT_OUT 40
    //#define SHIFT_EN 17

    #define LCD_PINS_RS 16
    #define LCD_PINS_ENABLE 17
    #define LCD_PINS_D4 23
    #define LCD_PINS_D5 25
    #define LCD_PINS_D6 27
    #define LCD_PINS_D7 29
  #endif

#endif //ULTRA_LCD

// SPI for Max6675 Thermocouple

#ifndef SDSUPPORT
// these pins are defined in the SD library if building with SD support
  #define SCK_PIN          52
  #define MISO_PIN         50
  #define MOSI_PIN         51
  #define MAX6675_SS       66// Do not use pin 53 if there is even the remote possibility of using Display/SD card
#else
  #define MAX6675_SS       66// Do not use pin 49 as this is tied to the switch inside the SD card socket to detect if there is an SD card present
#endif

#endif // AZTEEG X3 PRO
/****************************************************************************************/



/****************************************************************************************
* 7
* Ultimaker pin assignment
****************************************************************************************/

#if MB(ULTIMAKER)
#define KNOWN_BOARD

#ifndef __AVR_ATmega1280__
 #ifndef __AVR_ATmega2560__
 #error Oops!  Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
 #endif
#endif

#define LARGE_FLASH true

#define ORIG_X_STEP_PIN 25
#define ORIG_X_DIR_PIN 23
#define ORIG_X_MIN_PIN 22
#define ORIG_X_MAX_PIN 24
#define ORIG_X_ENABLE_PIN 27

#define ORIG_Y_STEP_PIN 31
#define ORIG_Y_DIR_PIN 33
#define ORIG_Y_MIN_PIN 26
#define ORIG_Y_MAX_PIN 28
#define ORIG_Y_ENABLE_PIN 29

#define ORIG_Z_STEP_PIN 37
#define ORIG_Z_DIR_PIN 39
#define ORIG_Z_MIN_PIN 30
#define ORIG_Z_MAX_PIN 32
#define ORIG_Z_ENABLE_PIN 35

#define ORIG_HEATER_BED_PIN 4
#define ORIG_TEMP_BED_PIN 10

#define ORIG_HEATER_0_PIN  2
#define ORIG_TEMP_0_PIN 8

#define ORIG_HEATER_1_PIN 3
#define ORIG_TEMP_1_PIN 9

#define ORIG_HEATER_2_PIN -1
#define ORIG_TEMP_2_PIN -1

#define ORIG_E0_STEP_PIN         43
#define ORIG_E0_DIR_PIN          45
#define ORIG_E0_ENABLE_PIN       41

#define ORIG_E1_STEP_PIN         49
#define ORIG_E1_DIR_PIN          47
#define ORIG_E1_ENABLE_PIN       48

#define SDPOWER            -1
#define SDSS               53
#define LED_PIN            13
#define ORIG_FAN_PIN            7
#define PS_ON_PIN          12
#define KILL_PIN           -1
#define SUICIDE_PIN        54  //PIN that has to be turned on right after start, to keep power flowing.

#ifdef ULTRA_LCD

  #ifdef NEWPANEL
  //arduino pin witch triggers an piezzo beeper
    #define BEEPER 18

    #define LCD_PINS_RS 20
    #define LCD_PINS_ENABLE 17
    #define LCD_PINS_D4 16
    #define LCD_PINS_D5 21
    #define LCD_PINS_D6 5
    #define LCD_PINS_D7 6

    //buttons are directly attached
    #define BTN_EN1 40
    #define BTN_EN2 42
    #define BTN_ENC 19  //the click

    #define SDCARDDETECT 38

  #else //old style panel with shift register
    //arduino pin witch triggers an piezzo beeper
    #define BEEPER 18

    //buttons are attached to a shift register
    #define SHIFT_CLK 38
    #define SHIFT_LD 42
    #define SHIFT_OUT 40
    #define SHIFT_EN 17

    #define LCD_PINS_RS 16
    #define LCD_PINS_ENABLE 5
    #define LCD_PINS_D4 6
    #define LCD_PINS_D5 21
    #define LCD_PINS_D6 20
    #define LCD_PINS_D7 19

    #define SDCARDDETECT -1
  #endif
#endif //ULTRA_LCD

#endif // ULTIMAKER
/****************************************************************************************/



/****************************************************************************************
* 70
* MegaTronics
****************************************************************************************/

#if MB(MEGATRONICS)
#define KNOWN_BOARD 1

#ifndef __AVR_ATmega2560__
  #error Oops!  Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
#endif

#define LARGE_FLASH        true

#define ORIG_X_STEP_PIN         26
#define ORIG_X_DIR_PIN          28
#define ORIG_X_ENABLE_PIN       24
#define ORIG_X_MIN_PIN          41
#define ORIG_X_MAX_PIN          37

#define ORIG_Y_STEP_PIN         60 // A6
#define ORIG_Y_DIR_PIN          61 // A7
#define ORIG_Y_ENABLE_PIN       22
#define ORIG_Y_MIN_PIN          14
#define ORIG_Y_MAX_PIN          15

#define ORIG_Z_STEP_PIN         54 // A0
#define ORIG_Z_DIR_PIN          55 // A1
#define ORIG_Z_ENABLE_PIN       56 // A2
#define ORIG_Z_MIN_PIN          18
#define ORIG_Z_MAX_PIN          19

#define ORIG_E0_STEP_PIN        31
#define ORIG_E0_DIR_PIN         32
#define ORIG_E0_ENABLE_PIN      38

#define ORIG_E1_STEP_PIN        34
#define ORIG_E1_DIR_PIN         36
#define ORIG_E1_ENABLE_PIN      30

#define SDPOWER            -1
#define SDSS               53
#define LED_PIN            13


#define ORIG_FAN_PIN            7 // IO pin. Buffer needed
#define PS_ON_PIN          12
#define KILL_PIN           -1

#define ORIG_HEATER_0_PIN       9    // EXTRUDER 1
#define ORIG_HEATER_1_PIN       8    // EXTRUDER 2 (FAN On Sprinter)
#define ORIG_HEATER_2_PIN       -1

#if TEMP_SENSOR_0 == -1
#define ORIG_TEMP_0_PIN         8   // ANALOG NUMBERING
#else
#define ORIG_TEMP_0_PIN         13   // ANALOG NUMBERING

#endif

#define ORIG_TEMP_1_PIN         15   // ANALOG NUMBERING
#define ORIG_TEMP_2_PIN         -1   // ANALOG NUMBERING
#define ORIG_HEATER_BED_PIN     10   // BED
#define ORIG_TEMP_BED_PIN       14   // ANALOG NUMBERING

#define BEEPER 33     // Beeper on AUX-4


#ifdef ULTRA_LCD

  #ifdef NEWPANEL
  //arduino pin which triggers an piezzo beeper

    #define LCD_PINS_RS 16
    #define LCD_PINS_ENABLE 17
    #define LCD_PINS_D4 23
    #define LCD_PINS_D5 25
    #define LCD_PINS_D6 27
    #define LCD_PINS_D7 29

    //buttons are directly attached using AUX-2
    #define BTN_EN1 59
    #define BTN_EN2 64
    #define BTN_ENC 43  //the click

    #define BLEN_C 2
    #define BLEN_B 1
    #define BLEN_A 0

    #define SDCARDDETECT -1   // Ramps does not use this port

      //encoder rotation values
    #define encrot0 0
    #define encrot1 2
    #define encrot2 3
    #define encrot3 1
#endif
#endif //ULTRA_LCD

#endif // MEGATRONICS
/****************************************************************************************/



/****************************************************************************************
* 701
* MegaTronics v2.0
****************************************************************************************/

#if MB(MEGATRONICS_2)
#define KNOWN_BOARD 1

#ifndef __AVR_ATmega2560__
  #error Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
#endif

#define LARGE_FLASH        true

#define ORIG_X_STEP_PIN 26
#define ORIG_X_DIR_PIN 27
#define ORIG_X_ENABLE_PIN 25
#define ORIG_X_MIN_PIN 37
#define ORIG_X_MAX_PIN 40 //2 //Max endstops default to disabled "-1", set to commented value to enable.

#define ORIG_Y_STEP_PIN 4 // A6
#define ORIG_Y_DIR_PIN 54 // A0
#define ORIG_Y_ENABLE_PIN 5
#define ORIG_Y_MIN_PIN 41
#define ORIG_Y_MAX_PIN 38 //15

#define ORIG_Z_STEP_PIN 56 // A2
#define ORIG_Z_DIR_PIN 60 // A6
#define ORIG_Z_ENABLE_PIN 55 // A1
#define ORIG_Z_MIN_PIN 18
#define ORIG_Z_MAX_PIN 19

#define ORIG_E0_STEP_PIN 35
#define ORIG_E0_DIR_PIN 36
#define ORIG_E0_ENABLE_PIN 34

#define ORIG_E1_STEP_PIN 29
#define ORIG_E1_DIR_PIN 39
#define ORIG_E1_ENABLE_PIN 28

#define ORIG_E2_STEP_PIN 23
#define ORIG_E2_DIR_PIN 24
#define ORIG_E2_ENABLE_PIN 22

#define SDPOWER -1
#define SDSS 53
#define LED_PIN 13

#define ORIG_FAN_PIN 7
#define FAN2_PIN 6
#define PS_ON_PIN 12
#define KILL_PIN -1

#define ORIG_HEATER_0_PIN 9 // EXTRUDER 1
#define ORIG_HEATER_1_PIN 8 // EXTRUDER 2
#define ORIG_HEATER_2_PIN -1
 
#define SHIFT_CLK 63
#define SHIFT_LD 42
#define SHIFT_OUT 17
#define SHIFT_EN 17
 
#if TEMP_SENSOR_0 == -1
  #define ORIG_TEMP_0_PIN 4 // ANALOG NUMBERING
#else
  #define ORIG_TEMP_0_PIN 13 // ANALOG NUMBERING
#endif


 #if TEMP_SENSOR_1 == -1
   #define ORIG_TEMP_1_PIN 8 // ANALOG NUMBERING
 #else
   #define ORIG_TEMP_1_PIN 15 // ANALOG NUMBERING
 #endif

 #define ORIG_TEMP_2_PIN -1 // ANALOG NUMBERING

 #define ORIG_HEATER_BED_PIN 10 // BED

 #if TEMP_SENSOR_BED == -1
   #define ORIG_TEMP_BED_PIN 8 // ANALOG NUMBERING
 #else
   #define ORIG_TEMP_BED_PIN 14 // ANALOG NUMBERING
 #endif

 #define BEEPER 64


 #define LCD_PINS_RS 14
 #define LCD_PINS_ENABLE 15
 #define LCD_PINS_D4 30
 #define LCD_PINS_D5 31
 #define LCD_PINS_D6 32
 #define LCD_PINS_D7 33


 //buttons are directly attached using keypad
 #define BTN_EN1 61
 #define BTN_EN2 59
 #define BTN_ENC 43 //the click

 #define BLEN_C 2
 #define BLEN_B 1
 #define BLEN_A 0

 #define SDCARDDETECT -1  // Megatronics does not use this port

   //encoder rotation values
 #define encrot0 0
 #define encrot1 2
 #define encrot2 3
 #define encrot3 1

#endif // MEGATRONICS_2
/****************************************************************************************/



/****************************************************************************************
* 702
* Minitronics v1.0
****************************************************************************************/

#if MB(MEGATRONICS_1)
#define KNOWN_BOARD 1


#ifndef __AVR_ATmega1281__
  #error Oops! Make sure you have 'Minitronics ' selected from the 'Tools -> Boards' menu.
#endif

 #define LARGE_FLASH        true

 #define ORIG_X_STEP_PIN 48
 #define ORIG_X_DIR_PIN 47
 #define ORIG_X_ENABLE_PIN 49
 #define ORIG_X_MIN_PIN 5
 #define ORIG_X_MAX_PIN -1 //2 //Max endstops default to disabled "-1", set to commented value to enable.

 #define ORIG_Y_STEP_PIN 39 // A6
 #define ORIG_Y_DIR_PIN 40 // A0
 #define ORIG_Y_ENABLE_PIN 38
 #define ORIG_Y_MIN_PIN 2
 #define ORIG_Y_MAX_PIN -1 //15

 #define ORIG_Z_STEP_PIN 42 // A2
 #define ORIG_Z_DIR_PIN 43 // A6
 #define ORIG_Z_ENABLE_PIN 41 // A1
 #define ORIG_Z_MIN_PIN 6
 #define ORIG_Z_MAX_PIN -1

 #define ORIG_E0_STEP_PIN 45
 #define ORIG_E0_DIR_PIN 44
 #define ORIG_E0_ENABLE_PIN 27

 #define ORIG_E1_STEP_PIN 36
 #define ORIG_E1_DIR_PIN 35
 #define ORIG_E1_ENABLE_PIN 37

 #define ORIG_E2_STEP_PIN -1
 #define ORIG_E2_DIR_PIN -1
 #define ORIG_E2_ENABLE_PIN -1
 
 #define SDPOWER -1
 #define SDSS               53

 #define LED_PIN 46
 
 #define ORIG_FAN_PIN 9
 #define FAN2_PIN -1
 #define PS_ON_PIN -1
 #define KILL_PIN -1
 
 #define ORIG_HEATER_0_PIN 7 // EXTRUDER 1
 #define ORIG_HEATER_1_PIN 8 // EXTRUDER 2
 #define ORIG_HEATER_2_PIN 9 // thermo couple
 
 #if TEMP_SENSOR_0 == -1
 	#define ORIG_TEMP_0_PIN 5 // ANALOG NUMBERING
 #else
 	#define ORIG_TEMP_0_PIN 7 // ANALOG NUMBERING
 #endif
 #define ORIG_TEMP_1_PIN 6 // ANALOG NUMBERING
 #define ORIG_TEMP_2_PIN -1 // ANALOG NUMBERING
 
 #define ORIG_HEATER_BED_PIN 3 // BED
 #define ORIG_TEMP_BED_PIN 6 // ANALOG NUMBERING
 
 #define BEEPER -1	
 
 
 #define LCD_PINS_RS -1
 #define LCD_PINS_ENABLE -1
 #define LCD_PINS_D4 -1
 #define LCD_PINS_D5 -1
 #define LCD_PINS_D6 -1
 #define LCD_PINS_D7 -1


 //buttons are directly attached using keypad
 #define BTN_EN1 -1
 #define BTN_EN2 -1
 #define BTN_ENC -1 //the click

 #define BLEN_C 2
 #define BLEN_B 1
 #define BLEN_A 0

 #define SDCARDDETECT -1  // Megatronics does not use this port

   //encoder rotation values
 #define encrot0 0
 #define encrot1 2
 #define encrot2 3
 #define encrot3 1

#endif // MEGATRONICS_1
/****************************************************************************************/



/****************************************************************************************
* 703
* MegaTronics v3.0
****************************************************************************************/

#if MB(MEGATRONICS_3)
#define KNOWN_BOARD 1
 
 
#ifndef __AVR_ATmega2560__
 #error Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
#endif
 
#define LARGE_FLASH        true
 

#define ORIG_X_STEP_PIN         58
#define ORIG_X_DIR_PIN          57
#define ORIG_X_ENABLE_PIN       59
#define ORIG_X_MIN_PIN          37
#define ORIG_X_MAX_PIN          40   //2 //Max endstops default to disabled "-1", set to commented value to enable.

#define ORIG_Y_STEP_PIN         5 // A6
#define ORIG_Y_DIR_PIN          17 // A0
#define ORIG_Y_ENABLE_PIN       4
#define ORIG_Y_MIN_PIN          41
#define ORIG_Y_MAX_PIN          38   //15

#define ORIG_Z_STEP_PIN         16 // A2
#define ORIG_Z_DIR_PIN          11 // A6
#define ORIG_Z_ENABLE_PIN       3 // A1
#define ORIG_Z_MIN_PIN          18
#define ORIG_Z_MAX_PIN          19
	 
#define ORIG_E0_STEP_PIN         28
#define ORIG_E0_DIR_PIN          27
#define ORIG_E0_ENABLE_PIN       29

#define ORIG_E1_STEP_PIN         25
#define ORIG_E1_DIR_PIN          24
#define ORIG_E1_ENABLE_PIN       26

#define ORIG_E2_STEP_PIN         22
#define ORIG_E2_DIR_PIN          60
#define ORIG_E2_ENABLE_PIN       23
	 
#define SDPOWER -1
#define SDSS 53
#define LED_PIN 13
 
#if NUM_SERVOS > 0
#define SERVO0_PIN 46
#endif

#define PS_ON_PIN 12
#define KILL_PIN -1
 

#define ORIG_HEATER_0_PIN 2 
#define ORIG_HEATER_1_PIN 8 
#define ORIG_HEATER_2_PIN 9 
#define ORIG_HEATER_BED_PIN 10 
#define ORIG_FAN_PIN 6
#define FAN2_PIN 7
 
#if TEMP_SENSOR_0 == -1
#define ORIG_TEMP_0_PIN 11 // ANALOG NUMBERING
#else
#define ORIG_TEMP_0_PIN 15 // ANALOG NUMBERING
#endif
 
#if TEMP_SENSOR_1 == -1
#define ORIG_TEMP_1_PIN 10 // ANALOG NUMBERING
#else
#define ORIG_TEMP_1_PIN 13 // ANALOG NUMBERING
#endif
 
#if TEMP_SENSOR_2 == -1
#define ORIG_TEMP_2_PIN 9 // ANALOG NUMBERING
#else
#define ORIG_TEMP_2_PIN 12 // ANALOG NUMBERING
#endif
 
#if TEMP_SENSOR_BED == -1
#define ORIG_TEMP_BED_PIN 8 // ANALOG NUMBERING
#else 
#define ORIG_TEMP_BED_PIN 14 // ANALOG NUMBERING
#endif

#define BEEPER 61	
 
#define LCD_PINS_RS 32 
#define LCD_PINS_ENABLE 31
#define LCD_PINS_D4 14
#define LCD_PINS_D5 30 
#define LCD_PINS_D6 39
#define LCD_PINS_D7 15
 
#define SHIFT_CLK 43
#define SHIFT_LD 35
#define SHIFT_OUT 34
#define SHIFT_EN 44

//buttons are directly attached using keypad
#define BTN_EN1 44
#define BTN_EN2 45
#define BTN_ENC 33 //the click
 
 #define BLEN_C 2
 #define BLEN_B 1
 #define BLEN_A 0

 #define SDCARDDETECT -1	// Megatronics does not use this port

   //encoder rotation values
 #define encrot0 0
 #define encrot1 2
 #define encrot2 3
 #define encrot3 1

#endif  // MEGATRONICS_3
/****************************************************************************************/



/****************************************************************************************
* 71
* Ultimaker pin assignment (Old electronics)
****************************************************************************************/

#if MB(ULTIMAKER_OLD)
#define KNOWN_BOARD

#ifndef __AVR_ATmega1280__
#ifndef __AVR_ATmega2560__
#error Oops!  Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
#endif
#endif

#define LARGE_FLASH true

#define ORIG_X_STEP_PIN 25
#define ORIG_X_DIR_PIN 23
#define ORIG_X_MIN_PIN 15
#define ORIG_X_MAX_PIN 14
#define ORIG_X_ENABLE_PIN 27

#define ORIG_Y_STEP_PIN 31
#define ORIG_Y_DIR_PIN 33
#define ORIG_Y_MIN_PIN 17
#define ORIG_Y_MAX_PIN 16
#define ORIG_Y_ENABLE_PIN 29

#define ORIG_Z_STEP_PIN 37
#define ORIG_Z_DIR_PIN 39
#define ORIG_Z_MIN_PIN 19
#define ORIG_Z_MAX_PIN 18
#define ORIG_Z_ENABLE_PIN 35

#define ORIG_HEATER_BED_PIN -1
#define ORIG_TEMP_BED_PIN -1

#define ORIG_HEATER_0_PIN  2
#define ORIG_TEMP_0_PIN 8

#define ORIG_HEATER_1_PIN 1
#define ORIG_TEMP_1_PIN 1

#define ORIG_HEATER_2_PIN -1
#define ORIG_TEMP_2_PIN -1

#define ORIG_E0_STEP_PIN         43
#define ORIG_E0_DIR_PIN          45
#define ORIG_E0_ENABLE_PIN       41

#define ORIG_E1_STEP_PIN         -1
#define ORIG_E1_DIR_PIN          -1
#define ORIG_E1_ENABLE_PIN       -1

#define SDPOWER            -1
#define SDSS               -1
#define LED_PIN            -1
#define ORIG_FAN_PIN            -1
#define PS_ON_PIN          -1
#define KILL_PIN           -1
#define SUICIDE_PIN        -1  //PIN that has to be turned on right after start, to keep power flowing.

#define LCD_PINS_RS 24
#define LCD_PINS_ENABLE 22
#define LCD_PINS_D4 36
#define LCD_PINS_D5 34
#define LCD_PINS_D6 32
#define LCD_PINS_D7 30

#endif // ULTIMAKER_OLD
/****************************************************************************************/



/****************************************************************************************
* 72
* Ultiboard v2.0 pin assignment
****************************************************************************************/

#if MB(ULTIMAIN_2)
#define KNOWN_BOARD

#ifndef __AVR_ATmega2560__
 #error Oops!  Make sure you have 'Arduino Mega 2560' selected from the 'Tools -> Boards' menu.
#endif

#define ORIG_X_STEP_PIN 25
#define ORIG_X_DIR_PIN 23
#define X_STOP_PIN 22
#define ORIG_X_ENABLE_PIN 27

#define ORIG_Y_STEP_PIN 32
#define ORIG_Y_DIR_PIN 33
#define Y_STOP_PIN 26
#define ORIG_Y_ENABLE_PIN 31

#define ORIG_Z_STEP_PIN 35
#define ORIG_Z_DIR_PIN 36
#define Z_STOP_PIN 29
#define ORIG_Z_ENABLE_PIN 34

#define ORIG_HEATER_BED_PIN 4
#define ORIG_TEMP_BED_PIN 10

#define ORIG_HEATER_0_PIN  2
#define ORIG_TEMP_0_PIN 8

#define ORIG_HEATER_1_PIN 3
#define ORIG_TEMP_1_PIN 9

#define ORIG_HEATER_2_PIN -1
#define ORIG_TEMP_2_PIN -1

#define ORIG_E0_STEP_PIN         42
#define ORIG_E0_DIR_PIN          43
#define ORIG_E0_ENABLE_PIN       37

#define ORIG_E1_STEP_PIN         49
#define ORIG_E1_DIR_PIN          47
#define ORIG_E1_ENABLE_PIN       48

#define SDPOWER            -1
#define SDSS               53
#define LED_PIN            8
#define ORIG_FAN_PIN            7
#define PS_ON_PIN          -1
#define KILL_PIN           -1
#define SUICIDE_PIN        -1  //PIN that has to be turned on right after start, to keep power flowing.
#define SAFETY_TRIGGERED_PIN     28 //PIN to detect the safety circuit has triggered
#define MAIN_VOLTAGE_MEASURE_PIN 14 //Analogue PIN to measure the main voltage, with a 100k - 4k7 resitor divider.

#define MOTOR_CURRENT_PWM_XY_PIN 44
#define MOTOR_CURRENT_PWM_Z_PIN 45
#define MOTOR_CURRENT_PWM_E_PIN 46
//Motor current PWM conversion, PWM value = MotorCurrentSetting * 255 / range
#define MOTOR_CURRENT_PWM_RANGE 2000
#define DEFAULT_PWM_MOTOR_CURRENT  {1300, 1300, 1250}

//arduino pin witch triggers an piezzo beeper
#define BEEPER 18

#define LCD_PINS_RS 20
#define LCD_PINS_ENABLE 15
#define LCD_PINS_D4 14
#define LCD_PINS_D5 21
#define LCD_PINS_D6 5
#define LCD_PINS_D7 6

//buttons are directly attached
#define BTN_EN1 40
#define BTN_EN2 41
#define BTN_ENC 19  //the click

#define BLEN_C 2
#define BLEN_B 1
#define BLEN_A 0

#define SDCARDDETECT 39

#endif // ULTIMAIN_2
/****************************************************************************************/



/****************************************************************************************
* 77
* 3DRAG
****************************************************************************************/

#if MB(3DRAG)
#define KNOWN_BOARD 1

#if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__)
  #error Oops!  Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
#endif

#define LARGE_FLASH true

#define ORIG_X_STEP_PIN         54
#define ORIG_X_DIR_PIN          55
#define ORIG_X_ENABLE_PIN       38
#define ORIG_X_MIN_PIN           3
#define ORIG_X_MAX_PIN           2

#define ORIG_Y_STEP_PIN         60
#define ORIG_Y_DIR_PIN          61
#define ORIG_Y_ENABLE_PIN       56
#define ORIG_Y_MIN_PIN          14
#define ORIG_Y_MAX_PIN          15

#define ORIG_Z_STEP_PIN         46
#define ORIG_Z_DIR_PIN          48
#define ORIG_Z_ENABLE_PIN       62
#define ORIG_Z_MIN_PIN          18
#define ORIG_Z_MAX_PIN          -1

#define Y2_STEP_PIN             36
#define Y2_DIR_PIN              34
#define Y2_ENABLE_PIN           30

#define Z2_STEP_PIN             36
#define Z2_DIR_PIN              34
#define Z2_ENABLE_PIN           30

#define ORIG_E0_STEP_PIN        26
#define ORIG_E0_DIR_PIN         28
#define ORIG_E0_ENABLE_PIN      24

#define ORIG_E1_STEP_PIN        36
#define ORIG_E1_DIR_PIN         34
#define ORIG_E1_ENABLE_PIN      30

#define SDPOWER                 -1
#define SDSS                    25
#define LED_PIN                 13


#define ORIG_FAN_PIN             8 // IO pin. Buffer needed

#define PS_ON_PIN                12

#if defined(REPRAP_DISCOUNT_SMART_CONTROLLER) || defined(G3D_PANEL)
  #define KILL_PIN               41
#else
  #define KILL_PIN               -1
#endif

#define ORIG_HEATER_0_PIN        10  // HOTEND 1
#define ORIG_HEATER_1_PIN        12  // HOTEND 2
#define ORIG_HEATER_2_PIN         6  // HOTEND 3
#define ORIG_HEATER_3_PIN        -1

#define ORIG_TEMP_0_PIN          13   // ANALOG NUMBERING
#define ORIG_TEMP_1_PIN          15   // ANALOG NUMBERING
#define ORIG_TEMP_2_PIN          -1   // ANALOG NUMBERING

#define ORIG_HEATER_BED_PIN       9   // NO BED

#define ORIG_TEMP_BED_PIN        14   // ANALOG NUMBERING

#if NUM_SERVOS > 0
  #define SERVO0_PIN             11
#endif

#if NUM_SERVOS > 1
  #define SERVO1_PIN              6
#endif

#if NUM_SERVOS > 2
  #define SERVO2_PIN              5
#endif

#if NUM_SERVOS > 3
  #define SERVO3_PIN              4
#endif

#define BEEPER                   33

#if defined(ULTRA_LCD) && defined(NEWPANEL)
  #define BEEPER -1

  #define LCD_PINS_RS 27
  #define LCD_PINS_ENABLE 29
  #define LCD_PINS_D4 37
  #define LCD_PINS_D5 35
  #define LCD_PINS_D6 33
  #define LCD_PINS_D7 31

  // Buttons
  #define BTN_EN1 16
  #define BTN_EN2 17
  #define BTN_ENC 23 //the click
#endif // ULTRA_LCD && NEWPANEL

// SPI for Max6675 Thermocouple
#ifndef SDSUPPORT
// these pins are defined in the SD library if building with SD support
  #define SCK_PIN          52
  #define MISO_PIN         50
  #define MOSI_PIN         51
  #define MAX6675_SS       66 // Do not use pin 53 if there is even the remote possibility of using Display/SD card
#else
  #define MAX6675_SS       66// Do not use pin 49 as this is tied to the switch inside the SD card socket to detect if there is an SD card present
#endif

#endif // 3DRAG
/****************************************************************************************/



/****************************************************************************************
* 78
* K8200
****************************************************************************************/

#if MB(K8200)
#define KNOWN_BOARD 1

#if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__)
  #error Oops!  Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
#endif

#define LARGE_FLASH true

#define ORIG_X_STEP_PIN         54
#define ORIG_X_DIR_PIN          55
#define ORIG_X_ENABLE_PIN       38
#define ORIG_X_MIN_PIN           3
#define ORIG_X_MAX_PIN           2

#define ORIG_Y_STEP_PIN         60
#define ORIG_Y_DIR_PIN          61
#define ORIG_Y_ENABLE_PIN       56
#define ORIG_Y_MIN_PIN          14
#define ORIG_Y_MAX_PIN          15

#define ORIG_Z_STEP_PIN         46
#define ORIG_Z_DIR_PIN          48
#define ORIG_Z_ENABLE_PIN       62
#define ORIG_Z_MIN_PIN          18
#define ORIG_Z_MAX_PIN          -1

#define Y2_STEP_PIN             36
#define Y2_DIR_PIN              34
#define Y2_ENABLE_PIN           30

#define Z2_STEP_PIN             36
#define Z2_DIR_PIN              34
#define Z2_ENABLE_PIN           30

#define ORIG_E0_STEP_PIN        26
#define ORIG_E0_DIR_PIN         28
#define ORIG_E0_ENABLE_PIN      24

#define ORIG_E1_STEP_PIN        36
#define ORIG_E1_DIR_PIN         34
#define ORIG_E1_ENABLE_PIN      30

#define SDPOWER                 -1
#define SDSS                    25
#define LED_PIN                 13


#define ORIG_FAN_PIN             8 // IO pin. Buffer needed

#define PS_ON_PIN                12

#if defined(REPRAP_DISCOUNT_SMART_CONTROLLER) || defined(G3D_PANEL)
  #define KILL_PIN               41
#else
  #define KILL_PIN               -1
#endif

#define ORIG_HEATER_0_PIN        10  // HOTEND 1
#define ORIG_HEATER_1_PIN        12  // HOTEND 2
#define ORIG_HEATER_2_PIN         6  // HOTEND 3
#define ORIG_HEATER_3_PIN        -1

#define ORIG_TEMP_0_PIN          13   // ANALOG NUMBERING
#define ORIG_TEMP_1_PIN          15   // ANALOG NUMBERING
#define ORIG_TEMP_2_PIN          -1   // ANALOG NUMBERING

#define ORIG_HEATER_BED_PIN       9   // NO BED

#define ORIG_TEMP_BED_PIN        14   // ANALOG NUMBERING

#if NUM_SERVOS > 0
  #define SERVO0_PIN             11
#endif

#if NUM_SERVOS > 1
  #define SERVO1_PIN              6
#endif

#if NUM_SERVOS > 2
  #define SERVO2_PIN              5
#endif

#if NUM_SERVOS > 3
  #define SERVO3_PIN              4
#endif

#define BEEPER                   33

#if defined(ULTRA_LCD) && defined(NEWPANEL)
  #define BEEPER -1

  #define LCD_PINS_RS 27
  #define LCD_PINS_ENABLE 29
  #define LCD_PINS_D4 37
  #define LCD_PINS_D5 35
  #define LCD_PINS_D6 33
  #define LCD_PINS_D7 31

  // Buttons
  #define BTN_EN1 16
  #define BTN_EN2 17
  #define BTN_ENC 23 //the click
#endif // ULTRA_LCD && NEWPANEL

// SPI for Max6675 Thermocouple
#ifndef SDSUPPORT
// these pins are defined in the SD library if building with SD support
  #define SCK_PIN          52
  #define MISO_PIN         50
  #define MOSI_PIN         51
  #define MAX6675_SS       66 // Do not use pin 53 if there is even the remote possibility of using Display/SD card
#else
  #define MAX6675_SS       66// Do not use pin 49 as this is tied to the switch inside the SD card socket to detect if there is an SD card present
#endif

#endif // K8200
/****************************************************************************************/



/****************************************************************************************
* 8 - 81
* Teensylu 0.7 / Printrboard pin assignments (AT90USB1286)
* Requires the Teensyduino software with Teensy++ 2.0 selected in Arduino IDE!
  http://www.pjrc.com/teensy/teensyduino.html
* See http://reprap.org/wiki/Printrboard for more info
****************************************************************************************/

#if MB(TEENSYLU) || MB(PRINTRBOARD)
#define KNOWN_BOARD 1
#define AT90USB 1286  // Disable MarlinSerial etc.

#ifndef __AVR_AT90USB1286__
#error Oops!  Make sure you have 'Teensy++ 2.0' selected from the 'Tools -> Boards' menu.
#endif

#ifdef AT90USBxx_TEENSYPP_ASSIGNMENTS  // use Teensyduino Teensy++2.0 pin assignments instead of Marlin traditional.
#error These Teensylu/Printrboard assignments depend on traditional Marlin assignments, not AT90USBxx_TEENSYPP_ASSIGNMENTS in fastio.h
#endif

#define LARGE_FLASH        true

#define ORIG_X_STEP_PIN          0
#define ORIG_X_DIR_PIN           1
#define ORIG_X_ENABLE_PIN       39

#define ORIG_Y_STEP_PIN          2
#define ORIG_Y_DIR_PIN           3
#define ORIG_Y_ENABLE_PIN       38

#define ORIG_Z_STEP_PIN          4
#define ORIG_Z_DIR_PIN           5
#define ORIG_Z_ENABLE_PIN       23

#define ORIG_E0_STEP_PIN         6
#define ORIG_E0_DIR_PIN          7
#define ORIG_E0_ENABLE_PIN      19

#define ORIG_HEATER_0_PIN       21  // Extruder
#define ORIG_HEATER_1_PIN       -1
#define ORIG_HEATER_2_PIN       -1
#define ORIG_HEATER_BED_PIN     20  // Bed
#define ORIG_FAN_PIN            22  // Fan
// You may need to change ORIG_FAN_PIN to 16 because Marlin isn't using fastio.h
// for the fan and Teensyduino uses a different pin mapping.

#if MB(TEENSYLU)  // Teensylu
  #define X_STOP_PIN         13
  #define Y_STOP_PIN         14
  #define Z_STOP_PIN         15
  #define ORIG_TEMP_0_PIN          7  // Extruder / Analog pin numbering
  #define ORIG_TEMP_BED_PIN        6  // Bed / Analog pin numbering
#else  // Printrboard
  #define X_STOP_PIN         35
  #define Y_STOP_PIN          8
  #define Z_STOP_PIN         36
  #define ORIG_TEMP_0_PIN          1  // Extruder / Analog pin numbering
  #define ORIG_TEMP_BED_PIN        0  // Bed / Analog pin numbering
  #ifdef FILAMENT_SENSOR
   #define FILWIDTH_PIN        2
  #endif //FILAMENT_SENSOR
#endif

#define ORIG_TEMP_1_PIN         -1
#define ORIG_TEMP_2_PIN         -1

#define SDPOWER            -1
#define SDSS                8
#define LED_PIN            -1
#define PS_ON_PIN          -1
#define KILL_PIN           -1
#define ALARM_PIN          -1

#ifndef SDSUPPORT
// these pins are defined in the SD library if building with SD support
  #define SCK_PIN           9
  #define MISO_PIN         11
  #define MOSI_PIN         10
#endif

#endif // TEENSYLU || PRINTRBOARD
/****************************************************************************************/




/****************************************************************************************
* 80
* RUMBA
****************************************************************************************/

#if MB(RUMBA)
#define KNOWN_BOARD 1

#ifndef __AVR_ATmega2560__
#error Oops!  Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
#endif

#define ORIG_X_STEP_PIN         17
#define ORIG_X_DIR_PIN          16
#define ORIG_X_ENABLE_PIN       48
#define ORIG_X_MIN_PIN          37
#define ORIG_X_MAX_PIN          36

#define ORIG_Y_STEP_PIN         54
#define ORIG_Y_DIR_PIN          47
#define ORIG_Y_ENABLE_PIN       55
#define ORIG_Y_MIN_PIN          35
#define ORIG_Y_MAX_PIN          34

#define ORIG_Z_STEP_PIN         57
#define ORIG_Z_DIR_PIN          56
#define ORIG_Z_ENABLE_PIN       62
#define ORIG_Z_MIN_PIN          33
#define ORIG_Z_MAX_PIN          32

#define ORIG_E0_STEP_PIN        23
#define ORIG_E0_DIR_PIN         22
#define ORIG_E0_ENABLE_PIN      24

#define ORIG_E1_STEP_PIN        26
#define ORIG_E1_DIR_PIN         25
#define ORIG_E1_ENABLE_PIN      27

#define ORIG_E2_STEP_PIN        29
#define ORIG_E2_DIR_PIN         28
#define ORIG_E2_ENABLE_PIN      39

#define LED_PIN            13

#define ORIG_FAN_PIN            7
//additional FAN1 PIN (e.g. useful for electronics fan or light on/off) on PIN 8

#define PS_ON_PIN          45
#define KILL_PIN           46

#if (TEMP_SENSOR_0==0)
 #define ORIG_TEMP_0_PIN         -1
 #define ORIG_HEATER_0_PIN       -1
#else
 #define ORIG_HEATER_0_PIN        2    // EXTRUDER 1
 #if (TEMP_SENSOR_0==-1)
  #define ORIG_TEMP_0_PIN         6    // ANALOG NUMBERING - connector *K1* on RUMBA thermocouple ADD ON is used
 #else
  #define ORIG_TEMP_0_PIN         15   // ANALOG NUMBERING - default connector for thermistor *T0* on rumba board is used
 #endif
#endif

#if (TEMP_SENSOR_1==0)
 #define ORIG_TEMP_1_PIN         -1
 #define ORIG_HEATER_1_PIN       -1
#else
 #define ORIG_HEATER_1_PIN        3    // EXTRUDER 2
 #if (TEMP_SENSOR_1==-1)
  #define ORIG_TEMP_1_PIN         5    // ANALOG NUMBERING - connector *K2* on RUMBA thermocouple ADD ON is used
 #else
  #define ORIG_TEMP_1_PIN         14   // ANALOG NUMBERING - default connector for thermistor *T1* on rumba board is used
 #endif
#endif

#if (TEMP_SENSOR_2==0)
 #define ORIG_TEMP_2_PIN         -1
 #define ORIG_HEATER_2_PIN       -1
#else
 #define ORIG_HEATER_2_PIN        6    // EXTRUDER 3
 #if (TEMP_SENSOR_2==-1)
  #define ORIG_TEMP_2_PIN         7    // ANALOG NUMBERING - connector *K3* on RUMBA thermocouple ADD ON is used <-- this can not be used when TEMP_SENSOR_BED is defined as thermocouple
 #else
  #define ORIG_TEMP_2_PIN         13   // ANALOG NUMBERING - default connector for thermistor *T2* on rumba board is used
 #endif
#endif

//optional for extruder 4 or chamber: #define TEMP_X_PIN         12   // ANALOG NUMBERING - default connector for thermistor *T3* on rumba board is used
//optional FAN1 can be used as 4th heater output: #define ORIG_HEATER_3_PIN       8    // EXTRUDER 4

#if (TEMP_SENSOR_BED==0)
 #define ORIG_TEMP_BED_PIN       -1
 #define ORIG_HEATER_BED_PIN     -1
#else
 #define ORIG_HEATER_BED_PIN      9    // BED
 #if (TEMP_SENSOR_BED==-1)
  #define ORIG_TEMP_BED_PIN       7    // ANALOG NUMBERING - connector *K3* on RUMBA thermocouple ADD ON is used <-- this can not be used when TEMP_SENSOR_2 is defined as thermocouple
 #else
  #define ORIG_TEMP_BED_PIN       11   // ANALOG NUMBERING - default connector for thermistor *THB* on rumba board is used
 #endif
#endif

#define SDPOWER            -1
#define SDSS               53
#define SDCARDDETECT       49
#define BEEPER             44
#define LCD_PINS_RS        19
#define LCD_PINS_ENABLE    42
#define LCD_PINS_D4        18
#define LCD_PINS_D5        38
#define LCD_PINS_D6        41
#define LCD_PINS_D7        40
#define BTN_EN1            11
#define BTN_EN2            12
#define BTN_ENC            43

#endif // RUMBA
/****************************************************************************************/




/****************************************************************************************
* 82
* Brainwave 1.0 pin assignments (AT90USB646)
* Requires hardware bundle for Arduino:
*  https://github.com/unrepentantgeek/brainwave-arduino
****************************************************************************************/

#if MB(BRAINWAVE)
#define KNOWN_BOARD 1

#define AT90USB 646  // Disable MarlinSerial etc.

#ifndef __AVR_AT90USB646__
#error Oops!  Make sure you have 'Brainwave' selected from the 'Tools -> Boards' menu.
#endif

#define ORIG_X_STEP_PIN         27
#define ORIG_X_DIR_PIN          29
#define ORIG_X_ENABLE_PIN       28
#define X_STOP_PIN          7
#define X_ATT_PIN          26

#define ORIG_Y_STEP_PIN         31
#define ORIG_Y_DIR_PIN          33
#define ORIG_Y_ENABLE_PIN       32
#define Y_STOP_PIN          6
#define Y_ATT_PIN          30

#define ORIG_Z_STEP_PIN         17
#define ORIG_Z_DIR_PIN          19
#define ORIG_Z_ENABLE_PIN       18
#define Z_STOP_PIN          5
#define Z_ATT_PIN          16

#define ORIG_E0_STEP_PIN        21
#define ORIG_E0_DIR_PIN         23
#define ORIG_E0_ENABLE_PIN      22
#define E0_ATT_PIN         20

#define ORIG_HEATER_0_PIN        4  // Extruder
#define ORIG_HEATER_1_PIN       -1
#define ORIG_HEATER_2_PIN       -1
#define ORIG_HEATER_BED_PIN     38  // Bed
#define ORIG_FAN_PIN             3  // Fan

#define ORIG_TEMP_0_PIN          7  // Extruder / Analog pin numbering
#define ORIG_TEMP_1_PIN         -1
#define ORIG_TEMP_2_PIN         -1
#define ORIG_TEMP_BED_PIN        6  // Bed / Analog pin numbering

#define SDPOWER            -1
#define SDSS               -1
#define LED_PIN            39
#define PS_ON_PIN          -1
#define KILL_PIN           -1
#define ALARM_PIN          -1

#ifndef SDSUPPORT
// these pins are defined in the SD library if building with SD support
  #define SCK_PIN           9
  #define MISO_PIN         11
  #define MOSI_PIN         10
#endif

#endif // BRAINWAVE
/****************************************************************************************/



/****************************************************************************************
* 83
* SAV MkI pin assignments (AT90USB1286)
* Requires the Teensyduino software with Teensy++ 2.0 selected in Arduino IDE!
* http://www.pjrc.com/teensy/teensyduino.html
* RepRap Clone Wars project board.
****************************************************************************************/

#if MB(SAV_MKI)  // SAV Mk-I
#define KNOWN_BOARD 1
#define AT90USB 1286  // Disable MarlinSerial etc.

#ifndef __AVR_AT90USB1286__
#error Oops!  Make sure you have 'Teensy++ 2.0' selected from the 'Tools -> Boards' menu.
#endif

#define LARGE_FLASH        true


#define ORIG_X_STEP_PIN         0
#define ORIG_X_DIR_PIN          1
#define ORIG_X_ENABLE_PIN       39

#define ORIG_Y_STEP_PIN         2
#define ORIG_Y_DIR_PIN          3
#define ORIG_Y_ENABLE_PIN       38

#define ORIG_Z_STEP_PIN         4
#define ORIG_Z_DIR_PIN          5
#define ORIG_Z_ENABLE_PIN       23

#define ORIG_E0_STEP_PIN         6
#define ORIG_E0_DIR_PIN          7
#define ORIG_E0_ENABLE_PIN       19

#define ORIG_HEATER_0_PIN       21  // Extruder
#define ORIG_HEATER_1_PIN       -1
#define ORIG_HEATER_2_PIN       -1
#define ORIG_HEATER_BED_PIN     20  // Bed
#define ORIG_FAN_PIN            16  // Fan   -- from Teensyduino environment.
                                    // For the fan and Teensyduino uses a different pin mapping.
#define X_STOP_PIN              13
#define Y_STOP_PIN              14
#define Z_STOP_PIN              15
//#define Z_STOP_PIN            36  // For inductive sensor.

#define ORIG_TEMP_0_PIN          7  // Extruder / Analog pin numbering
#define ORIG_TEMP_BED_PIN        6  // Bed / Analog pin numbering

#define ORIG_TEMP_1_PIN         -1
#define ORIG_TEMP_2_PIN         -1

#define SDPOWER                 -1
#define SDSS                    20  // PB0 - 8 in marlin env.
#define LED_PIN                 -1
#define PS_ON_PIN               -1
#define ALARM_PIN               -1
#define SDCARDDETECT            -1


#ifndef SDSUPPORT
   // these pins are defined in the SD library if building with SD support
  #define SCK_PIN          9
  #define MISO_PIN         11
  #define MOSI_PIN         10
#endif

#define BEEPER             -1
#define LCD_PINS_RS        -1
#define LCD_PINS_ENABLE    -1
#define LCD_PINS_D4        -1
#define LCD_PINS_D5        -1
#define LCD_PINS_D6        -1
#define LCD_PINS_D7        -1

#ifdef SAV_3DLCD
// For LCD SHIFT register LCD
#define SR_DATA_PIN         1
#define SR_CLK_PIN          0

#define BTN_EN1            41
#define BTN_EN2            40
#define BTN_ENC            12

#define KILL_PIN           42 // A2 = 42 - teensy = 40
#define HOME_PIN          -1 // A4 = marlin 44 - teensy = 42

#ifdef NUM_SERVOS
  #define SERVO0_PIN       41 // In teensy's pin definition for pinMode (in Servo.cpp)
#endif

#endif

#endif // SAV_MKI
/****************************************************************************************/




/****************************************************************************************
* 84
* Teensy++ 2.0 Breadboard pin assignments (AT90USB1286)
* Requires the Teensyduino software with Teensy++ 2.0 selected in Arduino IDE!
*  http://www.pjrc.com/teensy/teensyduino.html
* See http://reprap.org/wiki/Printrboard for more info
* CLI build: DEFINES=AT90USBxx_TEENSYPP_ASSIGNMENTS HARDWARE_MOTHERBOARD=84  make
****************************************************************************************/

#if MB(TEENSY2)
#define KNOWN_BOARD 1
#define AT90USB 1286  // Disable MarlinSerial etc.

#ifndef __AVR_AT90USB1286__
#error Oops!  Make sure you have 'Teensy++ 2.0' selected from the 'Tools -> Boards' menu.
#endif

#define LARGE_FLASH        true

/* 
DaveX plan for Teensylu/printrboard-type pinouts (ref teensylu & sprinter) for a TeensyBreadboard:

                               USB
           GND       GND |-----#####-----| +5V              ATX +5SB
     ATX PS_ON    PWM 27 |b7   #####   b6| 26    PWM*       Stepper Enable 
                  PWM  0 |d0           b5| 25    PWM*        
                  PWM  1 |d1           b4| 24    PWM        
         X_MIN         2 |d2           b3| 23               MISO_PIN
         Y_MIN         3 |d3           b2| 22               MOSI_PIN
         Z_MIN         4 |d4  * *      b1| 21               SCK_PIN       
                       5 |d5  e e      b0| 20               SDSS              
                LED    6 |d6  5 4      e7| 19               
                       7 |d7           e6| 18               
       LCD  RS         8 |e0             | GND              
       LCD  EN         9 |e1   a4 a0    R| AREF             
       LCD  D4        10 |c0   a5 a1   f0| 38 A0            ENC_1           
       LCD  D5        11 |c1   a6 a2   f1| 39 A1            ENC_2
       LCD  D6        12 |c2   a7 a3   f2| 40 A2            ENC_CLK
       LCD  D6        13 |c3           f3| 41 A3            
      Bed Heat    PWM 14 |c4   V G R   f4| 42 A4            
 Extruder Heat    PWM 15 |c5   c n S   f5| 43 A5            
           Fan    PWM 16 |c6   c d T   f6| 44 A6            Bed TC
                      17 |c7   * * *   f7| 45 A7            Extruder TC * 4.7k * +5        
                         -----------------                  

      Interior E4: 36, INT4
      Interior E5: 37, INT5
      Interior PA0-7: 28-35  -- Printrboard and Teensylu use these pins for step & direction:
             T++ PA Signal  Marlin
    
       Z STEP  32 a4  a0 28 X STEP
       Z DIR   33 a5  a1 29 X DIR
       E STEP  34 a6  a2 30 Y STEP
       E DIR   35 a7  a3 31 Y DIR

*/

#ifndef AT90USBxx_TEENSYPP_ASSIGNMENTS  // use Teensyduino Teensy++2.0 pin assignments instead of Marlin alphabetical.
  #error  Uncomment #define AT90USBxx_TEENSYPP_ASSIGNMENTS in fastio.h for this config
  // or build from command line with:  DEFINES=AT90USBxx_TEENSYPP_ASSIGNMENTS HARDWARE_MOTHERBOARD=84  make
#endif

#define ORIG_X_STEP_PIN         28 //  0 Marlin
#define ORIG_X_DIR_PIN          29 //  1 Marlin
#define ORIG_X_ENABLE_PIN       26 

#define ORIG_Y_STEP_PIN         30 //  2 Marlin
#define ORIG_Y_DIR_PIN          31 //  3
#define ORIG_Y_ENABLE_PIN       26     // Shared w/x

#define ORIG_Z_STEP_PIN         32 //  4
#define ORIG_Z_DIR_PIN          33 //  5
#define ORIG_Z_ENABLE_PIN       26 // Shared w/x

#define ORIG_E0_STEP_PIN        34 //  6
#define ORIG_E0_DIR_PIN         35 //  7
#define ORIG_E0_ENABLE_PIN      26 // Shared w/x

#define ORIG_HEATER_0_PIN       15 //  21  // Extruder
#define ORIG_HEATER_1_PIN       -1
#define ORIG_HEATER_2_PIN       -1
#define ORIG_HEATER_BED_PIN     14 // 20  // Bed
#define ORIG_FAN_PIN            16 // 22  // Fan

#define X_STOP_PIN          2
#define Y_STOP_PIN          3
#define Z_STOP_PIN          4

#define ORIG_TEMP_0_PIN          7 // Extruder / Analog pin numbering
#define ORIG_TEMP_BED_PIN        6 // Bed / Analog pin numbering
#define ORIG_TEMP_1_PIN         -1
#define ORIG_TEMP_2_PIN         -1

#define SDPOWER            -1
#define SDCARDDETECT       -1		
#define SDSS               20 // 8
#define LED_PIN             6
#define PS_ON_PIN          27
#define KILL_PIN           -1
#define ALARM_PIN          -1

#ifndef SDSUPPORT
// these pins are defined in the SD library if building with SD support
  #define SCK_PIN         21 // 9
  #define MISO_PIN        23 // 11
  #define MOSI_PIN        22 // 10
#endif

#ifdef ULTIPANEL
#define LCD_PINS_RS         8
#define LCD_PINS_ENABLE     9
#define LCD_PINS_D4        10
#define LCD_PINS_D5        11
#define LCD_PINS_D6        12
#define LCD_PINS_D7        13
#define BTN_EN1            38
#define BTN_EN2            39
#define BTN_ENC            40
#endif

#endif // TEENSY2
/****************************************************************************************/




/****************************************************************************************
* 88
* 5DPrint D8 Driver board
* https://bitbucket.org/makible/5dprint-d8-controller-board
****************************************************************************************/

#if MB(5DPRINT)

#define KNOWN_BOARD 1
#define AT90USB 1286  // Disable MarlinSerial etc.

#ifndef __AVR_AT90USB1286__
#error Oops!  Make sure you have 'Teensy++ 2.0' selected from the 'Tools -> Boards' menu.
#endif

#define LARGE_FLASH        true

#define ORIG_X_STEP_PIN          0
#define ORIG_X_DIR_PIN           1
#define ORIG_X_ENABLE_PIN       23
#define X_STOP_PIN              37

#define ORIG_Y_STEP_PIN          2
#define ORIG_Y_DIR_PIN           3
#define ORIG_Y_ENABLE_PIN       19
#define Y_STOP_PIN              36

#define ORIG_Z_STEP_PIN          4
#define ORIG_Z_DIR_PIN           5
#define ORIG_Z_ENABLE_PIN       18
#define Z_STOP_PIN              39

#define ORIG_E0_STEP_PIN         6
#define ORIG_E0_DIR_PIN          7
#define ORIG_E0_ENABLE_PIN      17

#define ORIG_HEATER_0_PIN       21  // Extruder
#define ORIG_HEATER_1_PIN       -1
#define ORIG_HEATER_2_PIN       -1
#define ORIG_HEATER_BED_PIN     20  // Bed
// You may need to change ORIG_FAN_PIN to 16 because Marlin isn't using fastio.h
// for the fan and Teensyduino uses a different pin mapping.
#define ORIG_FAN_PIN            16  // Fan

#define ORIG_TEMP_0_PIN          1  // Extruder / Analog pin numbering
#define ORIG_TEMP_BED_PIN        0  // Bed / Analog pin numbering

#define ORIG_TEMP_1_PIN         -1
#define ORIG_TEMP_2_PIN         -1

#define SDPOWER                 -1
#define LED_PIN                 -1
#define PS_ON_PIN               -1
#define KILL_PIN                -1
#define ALARM_PIN               -1

// The SDSS pin uses a different pin mapping from file Sd2PinMap.h
#define SDSS                    20

#ifndef SDSUPPORT
// these pins are defined in the SD library if building with SD support
  #define SCK_PIN                9
  #define MISO_PIN              11
  #define MOSI_PIN              10
#endif

// Microstepping pins
// Note that the pin mapping is not from fastio.h
// See Sd2PinMap.h for the pin configurations
#define X_MS1_PIN 25
#define X_MS2_PIN 26
#define Y_MS1_PIN 9
#define Y_MS2_PIN 8
#define Z_MS1_PIN 7
#define Z_MS2_PIN 6
#define E0_MS1_PIN 5
#define E0_MS2_PIN 4

#endif // 5DPRINT
/****************************************************************************************/




/****************************************************************************************
* 9
* Gen3+
****************************************************************************************/
#if MB(GEN3_PLUS)
#define MOTHERBOARD BOARD_SANGUINOLOLU_11   /*TODO: Figure out, Why is this done?*/
#define KNOWN_BOARD 1
#ifndef __AVR_ATmega644P__
#ifndef __AVR_ATmega1284P__
#error Oops!  Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu.
#endif
#endif

#define ORIG_X_STEP_PIN         15
#define ORIG_X_DIR_PIN          18
#define X_STOP_PIN         20

#define ORIG_Y_STEP_PIN         23
#define ORIG_Y_DIR_PIN          22
#define Y_STOP_PIN         25

#define ORIG_Z_STEP_PIN         27
#define ORIG_Z_DIR_PIN          28
#define Z_STOP_PIN         30

#define ORIG_E0_STEP_PIN        17
#define ORIG_E0_DIR_PIN         21

#define LED_PIN            -1

#define ORIG_FAN_PIN            -1

#define PS_ON_PIN         14
#define KILL_PIN           -1

#define ORIG_HEATER_0_PIN       12 // (extruder)

#define ORIG_HEATER_BED_PIN     16 // (bed)
#define ORIG_X_ENABLE_PIN       19
#define ORIG_Y_ENABLE_PIN       24
#define ORIG_Z_ENABLE_PIN       29
#define ORIG_E0_ENABLE_PIN      13

#define ORIG_TEMP_0_PIN          0   // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 33 extruder)
#define ORIG_TEMP_1_PIN         -1   
#define ORIG_TEMP_2_PIN         -1
#define ORIG_TEMP_BED_PIN        5   // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 34 bed)  
#define SDPOWER            -1
#define SDSS               4
#define ORIG_HEATER_2_PIN       -1

#endif // GEN3_PLUS
/****************************************************************************************/




/****************************************************************************************
* 90 - 91
* Open Motion controller with enable based extruders
*
*                        ATMega644
*
*                        +---\/---+
*            (D 0) PB0  1|        |40  PA0 (AI 0 / D31)
*            (D 1) PB1  2|        |39  PA1 (AI 1 / D30)
*       INT2 (D 2) PB2  3|        |38  PA2 (AI 2 / D29)
*        PWM (D 3) PB3  4|        |37  PA3 (AI 3 / D28)
*        PWM (D 4) PB4  5|        |36  PA4 (AI 4 / D27)
*       MOSI (D 5) PB5  6|        |35  PA5 (AI 5 / D26)
*       MISO (D 6) PB6  7|        |34  PA6 (AI 6 / D25)
*        SCK (D 7) PB7  8|        |33  PA7 (AI 7 / D24)
*                  RST  9|        |32  AREF
*                  VCC 10|        |31  GND
*                  GND 11|        |30  AVCC
*                XTAL2 12|        |29  PC7 (D 23)
*                XTAL1 13|        |28  PC6 (D 22)
*       RX0 (D 8)  PD0 14|        |27  PC5 (D 21) TDI
*       TX0 (D 9)  PD1 15|        |26  PC4 (D 20) TDO
*  INT0 RX1 (D 10) PD2 16|        |25  PC3 (D 19) TMS
*  INT1 TX1 (D 11) PD3 17|        |24  PC2 (D 18) TCK
*       PWM (D 12) PD4 18|        |23  PC1 (D 17) SDA
*       PWM (D 13) PD5 19|        |22  PC0 (D 16) SCL
*       PWM (D 14) PD6 20|        |21  PD7 (D 15) PWM
*                        +--------+
*
****************************************************************************************/

#if MB(OMCA_A) //Alpha OMCA board
#define KNOWN_BOARD 1

#ifndef __AVR_ATmega644__
#error Oops!  Make sure you have 'SanguinoA' selected from the 'Tools -> Boards' menu.
#endif

#define ORIG_X_STEP_PIN         21
#define ORIG_X_DIR_PIN          20
#define ORIG_X_ENABLE_PIN       24
#define X_STOP_PIN         0

#define ORIG_Y_STEP_PIN         23
#define ORIG_Y_DIR_PIN          22
#define ORIG_Y_ENABLE_PIN       24
#define Y_STOP_PIN         1

#define ORIG_Z_STEP_PIN         26
#define ORIG_Z_DIR_PIN          25
#define ORIG_Z_ENABLE_PIN       24
#define Z_STOP_PIN         2

#define ORIG_E0_STEP_PIN         28
#define ORIG_E0_DIR_PIN          27
#define ORIG_E0_ENABLE_PIN       24

#define ORIG_E1_STEP_PIN         -1 // 19
#define ORIG_E1_DIR_PIN          -1 // 18
#define ORIG_E1_ENABLE_PIN       24

#define ORIG_E2_STEP_PIN         -1 // 17
#define ORIG_E2_DIR_PIN          -1 // 16
#define ORIG_E2_ENABLE_PIN       24

#define SDPOWER            -1
#define SDSS               11
#define SDCARDDETECT       -1 // 10 optional also used as mode pin
#define LED_PIN            -1
#define ORIG_FAN_PIN            3
#define PS_ON_PIN          -1
#define KILL_PIN           -1

#define ORIG_HEATER_0_PIN       4
#define ORIG_HEATER_1_PIN       -1 // 12
#define ORIG_HEATER_2_PIN       -1 // 13
#define ORIG_TEMP_0_PIN          0 //D27   // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
#define ORIG_TEMP_1_PIN         -1 // 1
#define ORIG_TEMP_2_PIN         -1 // 2
#define ORIG_HEATER_BED_PIN     -1 // 14/15
#define ORIG_TEMP_BED_PIN       -1 // 1,2 or I2C
/*  Unused (1) (2) (3) 4 5 6 7 8 9 10 11 12 13 (14) (15) (16) 17 (18) (19) (20) (21) (22) (23) 24 (25) (26) (27) 28 (29) (30) (31)  */

#endif // OMCA_A

#if MB(OMCA)  // Final OMCA board -- REF http://sanguino.cc/hardware
#define KNOWN_BOARD 1

#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__)
#error Oops!  Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu. (Final OMCA board)
#endif

#define ORIG_X_STEP_PIN         26
#define ORIG_X_DIR_PIN          25
#define ORIG_X_ENABLE_PIN       10
#define X_STOP_PIN         0

#define ORIG_Y_STEP_PIN         28
#define ORIG_Y_DIR_PIN          27
#define ORIG_Y_ENABLE_PIN       10
#define Y_STOP_PIN         1

#define ORIG_Z_STEP_PIN         23
#define ORIG_Z_DIR_PIN          22
#define ORIG_Z_ENABLE_PIN       10
#define Z_STOP_PIN         2

#define ORIG_E0_STEP_PIN         24
#define ORIG_E0_DIR_PIN          21
#define ORIG_E0_ENABLE_PIN       10

/* future proofing */
#define __FS  20
#define __FD  19
#define __GS  18
#define __GD  13

#define UNUSED_PWM           14 /* PWM on LEFT connector */

#define ORIG_E1_STEP_PIN         -1 // 21
#define ORIG_E1_DIR_PIN          -1 // 20
#define ORIG_E1_ENABLE_PIN       -1 // 19

#define ORIG_E2_STEP_PIN         -1 // 21
#define ORIG_E2_DIR_PIN          -1 // 20
#define ORIG_E2_ENABLE_PIN       -1 // 18

#define SDPOWER            -1
#define SDSS               11
#define SDCARDDETECT       -1 // 10 optional also used as mode pin
#define LED_PIN            -1
#define ORIG_FAN_PIN            14 /* PWM on MIDDLE connector */
#define PS_ON_PIN          -1
#define KILL_PIN           -1

#define ORIG_HEATER_0_PIN        3 /*DONE PWM on RIGHT connector */
#define ORIG_HEATER_1_PIN       -1
#define ORIG_HEATER_2_PIN       -1
#define ORIG_HEATER_1_PIN       -1
#define ORIG_HEATER_2_PIN       -1
#define ORIG_TEMP_0_PIN          0 // ANALOG INPUT NUMBERING
#define ORIG_TEMP_1_PIN          1 // ANALOG
#define ORIG_TEMP_2_PIN         -1 // 2
#define ORIG_HEATER_BED_PIN      4
#define ORIG_TEMP_BED_PIN        2 // 1,2 or I2C

#define I2C_SCL       16
#define I2C_SDA       17

#endif // OMCA
/****************************************************************************************/



/****************************************************************************************
* 999
* Leapfrog Driver board
****************************************************************************************/
#if MB(LEAPFROG)  // Leapfrog board
#define KNOWN_BOARD 1

#ifndef __AVR_ATmega1280__
 #ifndef __AVR_ATmega2560__
 #error Oops!  Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
 #endif
#endif

#define ORIG_X_STEP_PIN         28
#define ORIG_X_DIR_PIN          63
#define ORIG_X_ENABLE_PIN       29
#define ORIG_X_MIN_PIN          47
#define ORIG_X_MAX_PIN          -1   //2 //Max endstops default to disabled "-1", set to commented value to enable.

#define ORIG_Y_STEP_PIN         14 // A6
#define ORIG_Y_DIR_PIN          15 // A0
#define ORIG_Y_ENABLE_PIN       39
#define ORIG_Y_MIN_PIN          48
#define ORIG_Y_MAX_PIN          -1   //15

#define ORIG_Z_STEP_PIN         31 // A2
#define ORIG_Z_DIR_PIN          32 // A6
#define ORIG_Z_ENABLE_PIN       30 // A1
#define ORIG_Z_MIN_PIN          49
#define ORIG_Z_MAX_PIN          -1

#define ORIG_E0_STEP_PIN        34  //34
#define ORIG_E0_DIR_PIN         35 //35
#define ORIG_E0_ENABLE_PIN      33 //33

#define ORIG_E1_STEP_PIN        37 //37
#define ORIG_E1_DIR_PIN         40 //40
#define ORIG_E1_ENABLE_PIN      36 //36

#define Y2_STEP_PIN             37
#define Y2_DIR_PIN              40
#define Y2_ENABLE_PIN           36

#define Z2_STEP_PIN             37
#define Z2_DIR_PIN              40
#define Z2_ENABLE_PIN           36

#define SDPOWER                 -1
#define SDSS                    11
#define SDCARDDETECT            -1 // 10 optional also used as mode pin
#define LED_PIN                 13
#define ORIG_FAN_PIN             7
#define PS_ON_PIN               -1
#define KILL_PIN                -1
#define SOL1_PIN                16
#define SOL2_PIN                17

#define ORIG_HEATER_0_PIN        9
#define ORIG_HEATER_1_PIN        8 // 12
#define ORIG_HEATER_2_PIN       11 //-1 // 13
#define ORIG_TEMP_0_PIN         13 //D27   // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
#define ORIG_TEMP_1_PIN         15 // 1
#define ORIG_TEMP_2_PIN         -1 // 2
#define ORIG_HEATER_BED_PIN     10 // 14/15
#define ORIG_TEMP_BED_PIN       14 // 1,2 or I2C
/*  Unused (1) (2) (3) 4 5 6 7 8 9 10 11 12 13 (14) (15) (16) 17 (18) (19) (20) (21) (22) (23) 24 (25) (26) (27) 28 (29) (30) (31)  */

#endif // LEAPFROG
/****************************************************************************************/



/****************************************************************************************
* 99
* Custom board
****************************************************************************************/

#if MB(99)
#define KNOWN_BOARD 1

#define ORIG_X_STEP_PIN          2
#define ORIG_X_DIR_PIN           3
#define ORIG_X_ENABLE_PIN       -1
#define X_STOP_PIN              16

#define ORIG_Y_STEP_PIN          5
#define ORIG_Y_DIR_PIN           6
#define ORIG_Y_ENABLE_PIN       -1
#define Y_STOP_PIN              67

#define ORIG_Z_STEP_PIN         62
#define ORIG_Z_DIR_PIN          63
#define ORIG_Z_ENABLE_PIN       -1
#define Z_STOP_PIN              59

#define ORIG_E0_STEP_PIN        65
#define ORIG_E0_DIR_PIN         66
#define ORIG_E0_ENABLE_PIN      -1

#define SDPOWER                 -1
#define SDSS                    53
#define LED_PIN                 -1
#define ORIG_FAN_PIN            -1
#define PS_ON_PIN                9
#define KILL_PIN                -1

#define ORIG_HEATER_0_PIN       13
#define ORIG_HEATER_1_PIN       -1
#define ORIG_HEATER_2_PIN       -1
#define ORIG_TEMP_0_PIN          6   // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
#define ORIG_TEMP_1_PIN         -1   // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
#define ORIG_TEMP_2_PIN         -1   // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
#define ORIG_HEATER_BED_PIN      4
#define ORIG_TEMP_BED_PIN       10

#endif // 99
/****************************************************************************************/

/****************************************************************************************
********************************* END MOTHERBOARD ***************************************
/****************************************************************************************/

#ifndef KNOWN_BOARD
  #error Unknown MOTHERBOARD value in configuration.h
#endif


/****************************************************************************************
************************************* FEATURE *******************************************
/****************************************************************************************/

#ifdef MKR4
#if (EXTRUDERS == 2) && (DRIVER_EXTRUDERS==1)     // Use this for one driver and two extruder
#define E0E1_CHOICE_PIN    5
#elif (EXTRUDERS == 3) && (DRIVER_EXTRUDERS==2)   // Use this for two driver and 3 extruder
#define E0E2_CHOICE_PIN    5
#elif (EXTRUDERS == 4) && (DRIVER_EXTRUDERS==2)   // Use this for two driver and 4 extruder
#define E0E2_CHOICE_PIN    5
#define E1E3_CHOICE_PIN    6
#endif // END EXTRUDERS
#endif // END MKR4

#ifdef NPR2
#ifdef DELTA
#define E_MIN_PIN          3  // Use pin ORIG_X_MIN_PIN
#else  // NO DELTA
#define ORIG_Z_MAX_PIN          -1 // Use pin ORIG_Z_MAX_PIN
#define E_MIN_PIN          19
#endif // END DELTA
#endif // END NPR2

#ifdef LASERBEAM
#define LASER_PWR_PIN	42
#define LASER_TTL_PIN	44
#endif

#ifdef FILAMENT_END_SWITCH
#define PAUSE_PIN          5
#endif
/****************************************************************************************/


#ifndef ORIG_HEATER_3_PIN
  #define ORIG_HEATER_3_PIN -1
#endif
#ifndef ORIG_TEMP_3_PIN
  #define ORIG_TEMP_3_PIN -1
#endif

//List of pins which to ignore when asked to change by gcode, 0 and 1 are RX and TX, do not mess with those!
#define _E0_PINS ORIG_E0_STEP_PIN, ORIG_E0_DIR_PIN, ORIG_E0_ENABLE_PIN, ORIG_HEATER_0_PIN,
#if DRIVER_EXTRUDERS > 1
  #define _E1_PINS ORIG_E1_STEP_PIN, ORIG_E1_DIR_PIN, ORIG_E1_ENABLE_PIN, ORIG_HEATER_1_PIN,
#else
  #define _E1_PINS
#endif
#if DRIVER_EXTRUDERS  > 2
  #define _E2_PINS ORIG_E2_STEP_PIN, ORIG_E2_DIR_PIN, ORIG_E2_ENABLE_PIN, ORIG_HEATER_2_PIN,
#else
  #define _E2_PINS
#endif
#if DRIVER_EXTRUDERS > 3
  #define _E3_PINS ORIG_E3_STEP_PIN, ORIG_E3_DIR_PIN, ORIG_E3_ENABLE_PIN, ORIG_HEATER_3_PIN,
#else
  #define _E3_PINS
#endif

#ifdef X_STOP_PIN
  #if X_HOME_DIR < 0
    #define ORIG_X_MIN_PIN X_STOP_PIN
    #define ORIG_X_MAX_PIN -1
  #else
    #define ORIG_X_MIN_PIN -1
    #define ORIG_X_MAX_PIN X_STOP_PIN
  #endif
#endif

#ifdef Y_STOP_PIN
  #if Y_HOME_DIR < 0
    #define ORIG_Y_MIN_PIN Y_STOP_PIN
    #define ORIG_Y_MAX_PIN -1
  #else
    #define ORIG_Y_MIN_PIN -1
    #define ORIG_Y_MAX_PIN Y_STOP_PIN
  #endif
#endif

#ifdef Z_STOP_PIN
  #if Z_HOME_DIR < 0
    #define ORIG_Z_MIN_PIN Z_STOP_PIN
    #define ORIG_Z_MAX_PIN -1
  #else
    #define ORIG_Z_MIN_PIN -1
    #define ORIG_Z_MAX_PIN Z_STOP_PIN
  #endif
#endif

#ifdef DISABLE_MAX_ENDSTOPS
#define ORIG_X_MAX_PIN          -1
#define ORIG_Y_MAX_PIN          -1
#define ORIG_Z_MAX_PIN          -1
#endif

#ifdef DISABLE_MIN_ENDSTOPS
#define ORIG_X_MIN_PIN          -1
#define ORIG_Y_MIN_PIN          -1
#define ORIG_Z_MIN_PIN          -1
#endif

#ifdef DELTA
#define ORIG_X_MIN_PIN          -1
#define ORIG_Y_MIN_PIN          -1
#endif



// Original pin assignmats to be used in configuration tool
#define X_STEP_PIN ORIG_X_STEP_PIN
#define X_DIR_PIN ORIG_X_DIR_PIN
#define X_ENABLE_PIN ORIG_X_ENABLE_PIN
#define X_MIN_PIN ORIG_X_MIN_PIN
#define X_MAX_PIN ORIG_X_MAX_PIN

#define Y_STEP_PIN ORIG_Y_STEP_PIN
#define Y_DIR_PIN ORIG_Y_DIR_PIN
#define Y_ENABLE_PIN ORIG_Y_ENABLE_PIN
#define Y_MIN_PIN ORIG_Y_MIN_PIN
#define Y_MAX_PIN ORIG_Y_MAX_PIN

#define Z_STEP_PIN ORIG_Z_STEP_PIN
#define Z_DIR_PIN ORIG_Z_DIR_PIN
#define Z_ENABLE_PIN ORIG_Z_ENABLE_PIN
#define Z_MIN_PIN ORIG_Z_MIN_PIN
#define Z_MAX_PIN ORIG_Z_MAX_PIN

#define E0_STEP_PIN ORIG_E0_STEP_PIN
#define E0_DIR_PIN ORIG_E0_DIR_PIN
#define E0_ENABLE_PIN ORIG_E0_ENABLE_PIN

#if DRIVER_EXTRUDERS > 1
#define E1_STEP_PIN ORIG_E1_STEP_PIN
#define E1_DIR_PIN ORIG_E1_DIR_PIN
#define E1_ENABLE_PIN ORIG_E1_ENABLE_PIN
#elif DRIVER_EXTRUDERS > 2
#define E2_STEP_PIN ORIG_E2_STEP_PIN
#define E2_DIR_PIN ORIG_E2_DIR_PIN
#define E2_ENABLE_PIN ORIG_E2_ENABLE_PIN
#elif DRIVER_EXTRUDERS > 3
#define E3_STEP_PIN ORIG_E3_STEP_PIN
#define E3_DIR_PIN ORIG_E3_DIR_PIN
#define E3_ENABLE_PIN ORIG_E3_ENABLE_PIN
#endif

#define FAN_PIN ORIG_FAN_PIN
#define HEATER_0_PIN ORIG_HEATER_0_PIN
#define HEATER_1_PIN ORIG_HEATER_1_PIN
#define HEATER_2_PIN ORIG_HEATER_2_PIN
#define HEATER_3_PIN ORIG_HEATER_3_PIN
#define HEATER_BED_PIN ORIG_HEATER_BED_PIN
#define TEMP_0_PIN ORIG_TEMP_0_PIN
#define TEMP_1_PIN ORIG_TEMP_1_PIN
#define TEMP_2_PIN ORIG_TEMP_2_PIN
#define TEMP_3_PIN ORIG_TEMP_3_PIN
#define TEMP_BED_PIN ORIG_TEMP_BED_PIN

#include "pins2tool.h"

#define SENSITIVE_PINS {0, 1, X_STEP_PIN, X_DIR_PIN, X_ENABLE_PIN, X_MIN_PIN, X_MAX_PIN, Y_STEP_PIN, Y_DIR_PIN, Y_ENABLE_PIN, Y_MIN_PIN, Y_MAX_PIN, Z_STEP_PIN, Z_DIR_PIN, Z_ENABLE_PIN, Z_MIN_PIN, Z_MAX_PIN, PS_ON_PIN, \
                        HEATER_BED_PIN, FAN_PIN,                  \
                        _E0_PINS _E1_PINS _E2_PINS _E3_PINS           \
                        analogInputToDigitalPin(TEMP_0_PIN), analogInputToDigitalPin(TEMP_1_PIN), analogInputToDigitalPin(TEMP_2_PIN), analogInputToDigitalPin(TEMP_3_PIN), analogInputToDigitalPin(TEMP_BED_PIN) }
#endif //__PINS_H
